Role of sand on curing of partex surface by UV radiation

A partex surface was modified by a UV‐curing system with epoxy acrylate (EB‐600). A set of formulations was prepared with oligomer and the trifunctional monomer trimethylol propane triacrylate in different combinations of percentages (1–5%) of sand to study the role of sand in various physical properties of UV‐cured thin films, as well as partex surfaces. Increased pendulum hardness (PH), gloss, adhesion, and abrasion values were obtained by the addition of sand into the partex surfaces. The best results were obtained with the formulation containing 3% sand. An enhanced PH and a decreased percentage of gel content of the UV‐cured film was observed with an increase of the sand concentration. A simulated weathering test was performed with partex surfaces cured by a formulation containing 3% sand in the base coat. The losses of the physical properties were found to be lower over the surface treated with the formulation containing sand. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 2385–2392, 2002     

Carbon fiber from natural biopolymer Bombyx mori silk fibroin with iodine treatment

Carbon fibers were prepared from silk fibers after an iodine treatment and the carbon yield, fiber morphology, structure and mechanical properties were investigated. A single or multi-step carbonization process was used for the preparation. In the single step process, silk fibroin (SF) fibers were heated from 25 to 800 °C with a heating rate of 5 °C min⁻¹ under Ar atmosphere. However, the carbon fiber obtained was partially melted and was too fragile to handle. For better performance, SF fibers were treated with iodine vapor at 100 °C for 12 h and untreated and iodinated SF fibers were heated from 25 to 800 °C by a multi-step carbonization process, which was defined based on the optimum thermal degradation rate of silk. In this multi-step process, the carbon fibers obtained from iodinated SF were structurally intact and stable in appearance, and the carbon yield achieved was ca. 36 wt.%, much higher than the value for untreated SF. X-ray diffraction, Raman spectroscopy and transmission electron microscopic observation revealed that the obtained carbon fibers from both untreated and iodinated SFs had a basically amorphous structure. The strength of carbon fibers prepared from iodinated SF using the multi-step carbonization was considerably increased compared to that of untreated SF. According to viscoelastic measurement, by heating above 280 °C the iodine introduced intermolecular cross-linking of the SF, and its melt flow was inhibited which produced a higher yield and better performance of the carbon fiber.     

Effect of alkali and ultraviolet (UV) radiation pretreatment on physical and mechanical properties of 1,6‐hexanediol diacrylate–grafted jute yarn by UV radiation

To improve the physicomechanical properties of jute yarn, grafting with 1,6‐hexanediol diacrylate (HDDA) monomer was performed by a UV radiation technique. A series of HDDA solutions of various concentrations in methanol were prepared. A small quantity of photoinitiator (Darocur‐1664) was also added to HDDA solutions. To optimize the conditions for grafting, the effects of monomer concentration, soaking time, and radiation doses were studied by varying the number of soaking times along with variation of monomer concentrations and UV radiation intensities. The extent of polymer loading and the mechanical properties like tensile strength (TS), elongation at break (Eb), and tensile modulus of both treated and untreated jute were investigated. The highest tensile strength, polymer loading, and modulus were achieved with 5% HDDA concentration, 5 min soaking time, and the 4th pass of UV radiation. This set of conditions was selected as optimum and produced enhanced tensile strength (67%), modulus (108%), and polymer loading (11%) over those of virgin fiber. To further improve the mechanical properties the jute yarns were pretreated with alkali (5% NaOH) solution and after that the alkali‐treated yarn were treated under UV radiation of various intensities. The pretreated samples were grafted with optimized monomer concentration (5% HDDA). Increased properties of alkali + UV‐pretreated and grafted samples such as polymer loading (12%), tensile strength (103%), elongation at break (46%), and modulus (114%) were achieved over those of virgin jute yarn. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 18–24, 2004     

Investigations on the Three Commercial Species of Rosaceae

Physico-chemical properties of the seed oils of three species of Rosaceae family, namely Prunus armeniaca (apricot), Prunus cerasifera (prune), and Prunus persica (peach) have been determined. Fatty acid composition of the oils and amino acids composition of seed cake proteins have also been determined and their utility in every day life has been discussed.     

Wear of graphite anodes during electrolysis of add sulphate solutions

Graphite electrodes were prepared by mixing calcined coke and coal tar pitch. They were pressed under 250 kg cm^–2 and heat treated up to 2800° C. Rectangles measuring 70 mm x 40 mm x 8 mm were anodically polarized under galvanostatic and potentiostatic conditions. Electrolyses were conducted at 10–50 mA cm^–2 for periods ranging from 10–120 hours in Na₂SO₄ solutions acidified with sulphuric acid to various pH values. The wear of graphite anodes increased with decreasing bath temperature, increasing acid concentration, decreasing pH of the electrolyte and increasing current density. A model is suggested which assumes that corrosion takes place via the formation of a lamellar crystal compound with the formula (C ₈ ⁰ O)(OH)₃HSO ₄ ^– ·2H₂SO₄.The compound is unstable at higher temperatures when corrosion is effected by oxidation of graphite by atomic oxygen. The formation of the carbon ions was found to be a necessary precondition for the formation of the complex.     

Pre‐necking and post‐necking relaxation and creep behavior of polycarbonate: A phenomenological study

Experiments have been performed to investigate the mechanical response of unfilled polycarbonate vis‐à‐vis the influence of prior deformation on stress relaxation and creep. Piecewise linear deformation histories, which involve strain‐controlled tensile loading of a specimen to a maximum load and partial unloading to a target strain/stress point as prologue to a relaxation test, have been shown to qualitatively influence the recorded stress‐time behavior. In particular, the stress magnitude during relaxation first increases and is then followed by a decrease. Analogously, in creep tests during unloading, the strain might decrease and then increase. Time characteristics for this U‐turn in the deformation response are influenced by the placement of the test. The influence of prior specimen conditioning on this phenomenon is investigated by comparing test data from virgin samples to that of specimens having high (～85%) inelastic strain from prior tensile elongation. Findings suggest that the observed persistence in the occurrence of this reversal effect for both types of specimens is evidence of the need to incorporate this behavior into the fold of material modeling. Additionally, this novel relaxation and creep behavior has been observed in other amorphous (poly(phenylene oxide)) and crystalline (high‐density polyethylene) polymers. Polym. Eng. Sci. 44:1783–1791, 2004. © 2004 Society of Plastics Engineers.     

Mathematical modeling of reverse osmosis systems

The present investigation pertains to modeling of seawater desalination system. A simulation model was developed and verified for a small-scale reverse osmosis system. The proposed model combines material balances on the feed tank, membrane module andproduct tank with membrane mass transfer models. Finally a comprehensive simulation model has been developed incorporating the effect of mass transfer inhibition The model is non-linear differential equation representing the feed concentration as a function of operating time and space. The solution of the simultaneous differential equations was obtained using the fourth order Runge-Kutta method, due to self starting and stability. The model was verified using the experimental data from the literature [17,24]. Parameter sensitivity was carried out to select the proper step size. The simulation was run for over 1000 11 enabling a prediction of operational performance at high overall system recoveries.     

Oxidation of Branched Chain Fatty Acids by Chromic Acid

The kinetics of oxidation of isobutyric and isovaleric acids by chromic acid in sulphuric acid medium have been studied. The end product acetic acid is supposed to be derived from the ketones which are the initial oxidation products of the corresponding branched chain fatty acids. The influence of acetic acid on the oxidation velocity has been examined and a marked effect on the rate constants with increasing acetic acid concentration has been observed. A mechanism involving the electrophilic attack of the oxidant on the tertiary carbon atom of the fatty acid to yield a carbonium ion has been postulated.     

A portable wireless body sensor data logger and its application in video capsule endoscopy

Due to the advancement of low power miniature electronic devices, there is growing interest of physiological data sensing and recording using wireless body sensor networks. The paper presents the design of a portable physiological data logger that includes rechargeable battery, wireless radio frequency and Bluetooth connectivity, and graphical display with touch screen capability. The target application is video capsule endoscopy. Image data are logged in micro SD cards which can be easily transferred to PC or Smartphone using SD card reader, USB interface or Bluetooth wireless link. The hardware design is general and can be used in various medical or industrial applications by changing only the firmware of the microcontroller. The design is prototyped in 109 × 107 × 20 mm printed circuit board (PCB). Tests with animal tissues have been conducted to demonstrate the performance advantages of the data logger. A demonstration of wireless heart pulse monitoring and data logging is also presented.     

UV‐radiation–induced preirradiation grafting of methyl methacrylate onto lignocellulose fiber in an aqueous medium and characterization

The preirradiation method of grafting has been established by ultraviolet radiation. Methyl methacrylate (MMA) was grafted onto jute fiber in an aqueous medium. The variation of graft weight with UV‐radiation time, monomer concentration, and reaction time was investigated. The conversion of monomer into homopolymer and graft copolymer was evaluated. The graft weight passes through a maximum value (～ 122%) with UV‐radiation time. The optimum value of the monomer concentration was evaluated for maximum degree of grafting. Graft copolymerization of MMA onto lignocellulose fiber significantly increases the elongation at break (～ 65%) compared to that of the “as‐received” sample. However, a linear decrease on breaking load was observed with the increase of graft weight. The estimation of degree of grafting was achieved using an IR technique by correlating band intensities with the degree of grafting. Considering the water‐absorption property, the grafted sample showed a maximum up to 61% decrease in hydrophilicity compared to that of the as‐received sample. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1667–1675, 2004