Experimental study on latent heat storage characteristics of W/O emulsion -Supercooling rate of dispersed water drops by direct contact heat exchange-

Recently, much attention has been paid to investigate the latent heat storage system. Using of ice heat storage system brings an equalization of electric power demand, because it will solved the electric -power-demand-concentration on day-time of summer by the air conditioning. The flowable latent heat storage material, Oil/Water type emulsion, microencapsulated latent heat material-water mixture or ice slurry, etc., is enable to transport the latent heat in a pipe. The flowable latent heat storage material can realize the pipe size reduction and system efficiency improvement. Supercooling phenomenon of the dispersed latent heat storage material in continuous phase brings the obstruction of latent heat storage. The latent heat storage rates of dispersed water drops in W/O (Water/Oil) emulsion are investigated experimentally in this study. The water drops in emulsion has the diameter within 3 ～ 25μm, the averaged water drop diameter is 7.3μm and the standard deviation is 2.9μm. The direct contact heat exchange method is chosen as the phase change rate evaluation of water drops in W/O emulsion. The supercooled temperature and the cooling rate are set as parameters of this study. The evaluation is performed by comparison between the results of this study and the past research. The obtained experimental result is shown that the 35K or more degree from melting point brings 100% latent heat storage rate of W/O emulsion. It was clarified that the supercooling rate of dispersed water particles in emulsion shows the larger value than that of the bulk water.     

Surface‐discharge electrode design methods for ACPDPs

Abstract— In order to lower development costs and to shorten development time, small panels, under 10‐in on the diagonal, are used for the experiments to improve the luminous efficiency of plasma‐display panels. However, it is difficult to show the same results as those of large panels, over 40 in. on the diagonal. In this paper, first, we show that the luminous efficiency and the voltage margin of mini‐panels are not obtained with large panels by using an actual 46‐in. PDP. The reason is that the resistance in the large panels is larger than that in the mini panels and the voltage drop in the large panels are larger than in mini‐panels. Therefore, we conclude that the bus electrode width and the transparent electrode width are important factors in the design of large PDPs. Next, we show the technique of designing large panels by using a database obtained from mini‐panels. The estimated cell‐design results show good agreement with an actual 46‐in. PDP in luminous efficiency and minimum sustain voltage. We show that a desired large PDP can be obtained by using the cell design proposed in the present paper.     

Formalization and Analysis of Class Loading in Java

Since Java security relies on the type-safety of the JVM, many formal approaches have been taken in order to prove the soundness of the JVM. This paper presents a new formalization of the JVM and proves its soundness. It is the first model to employ dynamic linking and bytecode verification to analyze the loading constraint scheme of Java2. The key concept required for proving the soundness of the new model is augmented value typing, which is defined from ordinary value typing combined with the loading constraint scheme. In proving the soundness of the model, it is shown that there are some problems inside the current reference implementation of the JVM with respect to our model. We also analyze the findClass scheme, newly introduced in Java2. The same analysis also shows why applets cannot exploit the type-spoofing vulnerability reported by Saraswat, which led to the introduction of the loading constraint scheme.     

The effects of a convex rear-view mirror on ocular accommodative responses

Convex mirrors are universally used as rear-view mirrors in automobiles. However, the ocular accommodative responses during the use of these mirrors have not yet been examined. This study investigated the effects of a convex mirror on the ocular accommodative systems. Seven young adults with normal visual functions were ordered to binocularly watch an object in a convex or plane mirror. The accommodative responses were measured with an infrared optometer. The average of the accommodation of all subjects while viewing the object in the convex mirror were significantly nearer than in the plane mirror, although all subjects perceived the position of the object in the convex mirror as being farther away. Moreover, the fluctuations of accommodation were significantly larger for the convex mirror. The convex mirror caused the 'false recognition of distance', which induced the large accommodative fluctuations and blurred vision. Manufactures should consider the ocular accommodative responses as a new indicator for increasing automotive safety.     

A new technology for the production of aluminum matrix composites by the plasma synthesis method

Aluminum matrix composites were produced via the plasma injection of reinforcing particulates into aluminum melts stirred electromagnetically. In this process, a metallic wire supplied to the active zone of plasma torch disintegrated into fine metallic particles. In the plasma arc, the particles are heated above the melting point and accelerated to close to sonic speed, which helps with the incorporation of the particles into the melt. In this study, the possibility of producing aluminum matrix composites reinforced by intermetallic compound particles via plasma synthesis is demonstrated.     

Crystallization behaviours around the glass transition temperature in an amorphous Fe–Nb–B alloy

Crystallization behaviours around the glass transition temperature in an amorphous Fe₇₀Nb₁₀B₂₀ alloy were investigated by means of transmission electron microscopy. Dense bcc-Fe nanocrystals initially appeared as the primary phase, followed by the dense formation of the (Fe,Nb)₂₃B₆ nanocrystalline phase. The bcc-Fe nanocrystals were formed even by annealing at a temperature that is 38 K lower than the glass transition temperature. A difference of the low temperature behaviours between the present conventional amorphous alloy and a bulk metallic glass was discussed.     

Numerical Modeling of an Earthquake-Induced Landslide Considering the Strain-Softening Characteristics at the Bedding Plane

The damage caused by an earthquake-induced landslide can generally be classified as either a limited deformation or a catastrophic failure. From an engineering point of view, the latter can be much more dangerous because the sliding mass may continue moving until it collides with another object. If a catastrophic failure occurs near a river, the debris may block the river, causing serious damage to the adjacent area. Therefore, examination of the mechanism of such catastrophic slope failures is important with respect to the mitigation of earthquake disasters in mountainous districts, although numerical modeling of such phenomena is rather difficult. In the present study, a new numerical model is developed to simulate an earthquake-induced catastrophic landslide that occured at a typical dip slope, namely, the Yokowatashi Landslide in Japan. In this case, the upper part of the bedrock on the planer tectonic dip surface slid more than 70 m. Only shear-strength degradation at the bedding plane could cause such a long-distance traveling failure. To investigate the strain-softening characteristics of the materials that filled the bedding plane, a series of laboratory tests involving undisturbed block samples was performed. The measured stress-displacement relationships under cyclic loading were numerically modeled as a newly proposed elasto-plastic constitutive model to be used in numerical simulations of landslide, based on the dynamic finite element method. The observed phenomena were appropriately simulated by the proposed method. The mechanism of catastrophic failure is discussed in detail in this paper in order to clarify the relationships between the strain-softening characteristics and the global slope stability. Our newly proposed method to evaluate the possibility of a catastrophic failure was applied to the landslide, and the moment when the slope becomes unstable was able to be predicted. The results confirm that the proposed method can predict the catastrophic failure of a slope.     

Nitritation performance in membrane-aerated biofilm reactors differs from conventional biofilm systems

Nitrogen removal via nitrite has gained increasing attention in recent years due to its potential cost savings. Membrane-aerated biofilm reactors (MABRs) are one potential technology suitable to achieve nitritation. In this study we compared lab scale MABRs with conventional biofilm reactors to evaluate the influence of environmental conditions and operational parameters on nitritation performance. The oxygen mass transfer rate is postulated as a crucial parameter to control nitritation in the MABR: Clean water measurements showed significant underestimation of the total oxygen mass transfer, however, accurate determination of the oxygen mass transfer coefficient (k_m) of the system could be achieved by adjusting the liquid-phase mass transfer resistance in the constructed model. Batch experiments at different initial ammonium concentrations revealed that the conventional biofilm geometry was superior for nitritation compared to MABRs. These differences were reflected well in estimates of the oxygen affinity constants of the key microbial players, AOB and NOB (K_O,AOB < K_O,NOB (in both systems) and K_O,NOB values smaller in the MABR vs. the conventional biofilm system). It also appeared that – in addition to oxygen limitation – the absolute and relative substrate concentrations in the biofilm (esp. of oxygen) are very important for successful nitritation. Initial biomass composition, furthermore, impacted reactor performance in the MABR systems indicating the need for appropriate inoculum choice.