A numerical study on determination of volume averaged thermal transport properties of metal foam structures using X-ray microtomography technique

Abstract

Volume averaged thermal transport properties of two metal foams with 10 and 20 PPI are obtained by using microtomography technique. The digital 3D structures of samples are generated in computer environment. The governing equations are solved for the entire domain and the volume averaged technique is used to determine interfacial heat transfer coefficient, longitudinal and transverse thermal dispersion conductivity. The study is performed for the pore scale Reynolds number from 100 to 600. The obtained results are within the ranges of the suggested correlations in literature. The present study supports the correlations suggested by Calmidi and Mahajan (2000) and Zhang et al. (2016).     

Design of a photocatalyst for bromate decomposition: surface modification of TiO2 by pseudo-boehmite

The rate of BrO3- reduction by a commercial TiO2 photocatalyst under UV illumination in an aqueous solution was increased by lowering the pH from 7 to 5. The effect is attributable to an enhancement of the electrical interaction between BrO3- and the positively charged surfaces of the TiO2 photocatalyst. The surface charge can be controlled by a surface modification of the TiO2 photocatalyst without controlling the pH of the water. In fact, the isoelectric point of surface-modified TiO2 was higher than that of the unloaded TiO2 photocatalyst, resulting in an increase in the rate of the photocatalytic reduction of BrO3- at a neutral pH. This increase is explained by an increase in the amount of adsorbed BrO3- on the photocatalyst surface.     

Thermal Feasibility Analyses for the 1356MWe High Conversion-Type Innovative Water Reactor for Flexible Fuel Cycle

A new reactor concept of innovative water reactor for flexible fuel cycle (FLWR) is under development at Japan Atomic Energy Agency in cooperation with Japanese reactor suppliers. A design of 1,356 MWe high conversion boiling water reactor-type FLWR core, which has an instantaneous conversion ratio of 1.04, negative void coefficient, high burnup of 65 GWd/t, and 15-month operational cycle length, has been constructed. So far, studies on thermal-hydraulic characteristics have been performed for tight lattice core. Evaluation methods for the critical power and the pressure drop under both the steady and the transient states have been established, and a modified TRAC-BF1 code has been developed for the thermal-hydraulic design of the FLWR. In this paper, the thermal feasibility of the designed 1356MWe FLWR core is analyzed by using the modified TRAC-BF1 code. The analysis is first carried out for the current core design. It is confirmed that no boiling transition (BT) occurs under the steady state. However, the minimum critical power ratio (MCPR) is only about 1.08, and the BT is confirmed occurring under the postulated abnormal transient processes. Therefore, concretizations of the conditions that ensure the thermal feasibility of a natural circulation-type FLWR and a forced circulation-type FLWR are performed. As for the results, for a forced circulation-type FLWR, the operation-limited MCPR (OLMCPR) is 1.32, and the necessary minimum core coolant flow rate is 640 kg/(m²s). For a natural circulation-type FLWR, the OLMCPR is 1.19, and the necessary minimum core coolant flow rate is 560 kg/(m²s).     

Measurement of Liquid Film Thickness by a Fringe Method

A technique was developed and tested to measure the local thickness of a droplet or a liquid film on a surface of an opaque or thick single transparent plate by an interference fringe pattern that was easily formed by reflecting laser lights. Monochromatic epi-illumination through an objective lens of a conventional microscope was provided by a 5 mW or 300 mW laser and a filter to remove the noise caused by laser speckle. The incremental height difference of the liquid layer between neighboring maxima or minima of fringes was evaluated from the wavelength of the laser light and the refractive index of the liquid. Estimation error of a local inclination angle was discussed using ray tracing under parallel illumination approximation. Droplet profiles evaluated from the interferogram that were obtained by the present fringe method agreed well with those by Laser Focus Displacement Meter. Measurement was made to ensure the usefulness of the present technique. It was made clear that the contact angle of a liquid droplet could be obtained precisely and swiftly, even in small size or small contact angle, and that instantaneous three-dimensional profile of a liquid film on a bubble moving in a microchannel could be measured. The fringe method had sufficient potential to obtain more detailed information about three-dimensional characteristics of liquid film in flows such as the generation, breakdown, and growth of waves and the liquid film on a bubble at the beginning of movement.     

Subcooled Flow Boiling in a Minichannel

It has been considered that dry-out occurs easily in boiling heat transfer for a small channel, a mini- or microchannel, because the channel was easily filled with coalescing vapor bubbles. In the present study, the experiments of subcooled flow boiling of water were performed under atmospheric conditions for a horizontal rectangular channel for which the size is 1 mm height and 1 mm width, with a flat heating surface of 10 mm length and 1 mm width placed on the bottom of the channel. The heating surface has a top of copper heating block and is heated by ceramic heaters. In the high heat flux region of nucleate boiling, about 70–80% of the heating surface was covered with a large coalescing bubble and the boiling reached critical heat flux as observed by high-speed video. In the beginning of transition boiling, coalescing bubbles were collapsed to many fine bubbles and microbubble emission boiling was observed at liquid subcooling higher than 30 K. The maximum heat flux obtained was 8 MW/m² (800 W/cm²) at liquid subcooling of higher than 40 K and a liquid velocity of 0.5 m/s. However, the surface temperature was very much higher than that of a centimeter-scale channel. The high-speed video photographs indicated that microbubble emission boiling occurs in the deep transition boiling region.     

Simultaneous determination of pesticides in agricultural products by LC/MS/MS using clean-up with ultrafiltration

A method for simultaneous determination of multiple pesticide residues in agricultural products was developed by using a pretreatment with ultrafiltration, followed by liquid chromatography-tandem mass spectrometry (LC/MS/MS). The pretreatment process (extraction of pesticides from agricultural products with methanol, dilution of the extract with water, and ultrafiltration) gave recoveries in the range of 50-150% for 63 of 83 pesticides spiked at 0.25 microg/ g into 6 agricultural products. The detection limits of pesticides by LC/MS/MS were below 0.0005-0.05 micro/g. This method is useful for screening purposes and for multiresidue analysis of pesticides in agricultural products. Pesticide residues in 50 domestic crops were investigated by this method, and residues of 14 pesticides were detected in 30 crops.     

Slow interfacial charge recombination in solid-state dye-sensitized solar cell using Al2O3-coated nanoporous TiO2 films

Al₂O₃-coated TiO₂ porous films were used to fabricate solid-state dye-sensitized solar cells using CuI as hole conductor. Investigation with transient photovoltage measurements showed that the Al₂O₃ interlayer slowed down the interfacial recombination of electrons in TiO₂ with holes in CuI by forming a potential barrier at the TiO₂/CuI interface. As a consequence, the cell made from Al₂O₃-coated TiO₂ film showed superior cell performance than the cell made from TiO₂ film only, especially under relative high intensity of simulated sunlight.     

Thermal diffusivity and porosity of solid materials by the electromagnetic ultrasonic technique. Part 3—simultaneous measurement of ultrasonic velocity and thermal diffusivity

The objective of this study is to evaluate simultaneously the time dependence of the thermal diffusivity of carbon-carbon composites (C/C composites) and their porosity during heat treatment using the electromagnetic ultrasonic technique. This paper describes two kinds of experiments conducted to confirm the principle for simultaneous measurement of both the ultrasonic velocity (used to evaluate the porosity) and the thermal diffusivity at room temperature. For each material, the samples used in both experiments were identical. The ultrasonic velocity of type 304 stainless steel and its thermal diffusivity were 5.85 km/s and 3.8 mm²/s with precisions of ±1.6 and ±8 percent, respectively. The ultrasonic velocity of a two-dimensional woven C/C composite and its thermal diffusivity were 2.86 km/s and 4.8 mm²/s with precisions of ±5.0 and ±8 percent, respectively. The results appear to indicate that the electromagnetic ultrasonic technique can measure the ultrasonic velocity and the thermal diffusivity simultaneously and that it is also applicable to C/C composites. © 1997 Scripta Technica, Inc. Heat Trans Jpn Res, 25(5): 308–322, 1996     

A novel spherical carbon

We developed a novel spherical carbon material. The spherical carbon is composed of a high density of carbon nanotubes or nanofilaments, and includes an oxidized diamond particle as a core. Syntheses of this carbon in high volume with high selectivity may be possible. It is expected that this carbon will be useful as a catalyst material for fuel cells, electric double-layer capacitors, etc.     

Simplified method for determining cadmium concentrations in rice foliage and soil by using a biosensor kit with immunochromatography

BACKGROUND: The behavior of cadmium in ecosystems needs to be monitored because of the human toxicity of this heavy metal. The need recently arose for a simple and quick on‐site test for trace levels of Cd in food and environmental samples. In response, an immunochromatographic assay kit for detecting Cd was manufactured by Kansai Electric Power Co. of Japan. This kit uses the antigen–antibody complex reaction between the Cd–EDTA complex and an anti‐Cd–EDTA antibody and shows the results in terms of the degree of color developed on a test paper. We previously reported the successful use of this kit to determine Cd concentrations in brown rice. Here, we applied the kit to the determination of Cd concentrations in rice foliage and soil. RESULTS: Cadmium in rice foliage was not extracted successfully by the method used for brown rice. However, it was successfully extracted by 0.1 mol L^?1 HCl solution at a rice foliage:HCl ratio of 1:20, and coexisting metals were removed sufficiently by the column treatment. The Cd concentrations determined by immunochromatographic assay were well correlated with the values obtained by acid decomposition and inductively coupled plasma mass spectrometry. The 0.1 mol L^?1 HCl‐extractable Cd concentration in soil was also determined successfully with the kit. CONCLUSION: Approximate Cd concentrations in rice plants and 0.1 mol L^?1 HCl‐extractable Cd concentrations in soil can be monitored easily and quickly by this method at locations where facilities for acid digestion and precision analysis are not available. Copyright © 2009 Society of Chemical Industry