Cellulose nanocrystal-mediated assembly of graphene oxide in natural rubber nanocomposites with high electrical conductivity

This study reports a green and powerful strategy for preparing cellulose nanocrystal (CNC)/graphene oxide (GO)/natural rubber (NR) nanocomposites hosting a 3D hierarchical conductive network. Due to good dispersibility and amphiphilic nature of CNC, well dispersed CNC/GO nanohybrids were prepared. Hydrogen bonding interactions between CNC and GO greatly enhanced the stability of the CNC/GO nanohybrids. CNC/GO nanohybrids were introduced into NR latex under sonication and the mixture was cast. Self-assembled CNC/GO nanohybrids preferentially dispersed in the interstice between latex microspheres allowing the construction of a 3D hierarchical conductive network. By combining strong hydrogen bonds and 3D conductive network, both electrical conductivity and mechanical properties (tensile strength and modulus) have been significantly improved. The electrical conductivity of the nanocomposite with 4 wt% GO and 5 wt% CNC exhibited an increase of nine orders of magnitude compared to the nanocomposite with only 4 wt% GO; meanwhile, the electrical percolation threshold was 3-fold lower than for NR/GO composites.     

钛基复合材料的高周疲劳性能研究

研究了TiC粒子增强的钛基复合材料的室温轴向高周疲劳性能。测试Kt=1的试样时采用的试验频率为76Hz，R＝0．06和R＝－1时，复合材料的室温疲劳强度分别为594MPa和494MPa。试验结果表明TiC粒子增强的钛基复合材料的室温高周疲劳性能与细晶组织的Ti-6Al-4V和IMI834的相当。复合材料内含有较细小的薄片状组织，这种组织为α β相互相交错构成，这种细小的α β相间的层状组织对于阻止疲劳裂纹的扩展和提高疲劳裂纹的扩展寿命有重要作用。退火后的复合材料疲劳裂纹扩展区规则且较宽广，从而也使复合材料具有较高的疲劳强度，疲劳裂纹扩展寿命延长。     

Methanol Selective Oxidation to Formaldehyde over Iron-Molybdate Catalysts

This review deals with the important industrial reaction of formaldehyde manufacture by methanol oxidation over iron molybdate catalysts. Detailed reference is made to the used catalyst, preparation techniques (coprecipitation, sol-gel like, mechanical mixing, etc.) including unsupported and supported catalysts, promoters and characterization methods. The controversial active phase assignment (stoichiometric versus Mo rich iron molybdate) is discussed. The proposed reaction mechanisms and kinetic laws for the main and side reactions are examined. The catalyst deactivation processes are reviewed and the role of Mo excess on these processes is underlined. Finally conclusions and perspectives are presented.     

Influence of Substrate Properties on the Formation of Suspension Plasma Sprayed Coatings

In this study, YSZ coatings were deposited on different substrate materials (stainless steel and aluminum) using suspension plasma spray technique. The effects of substrate properties (material, surface topology, temperature, and thickness) on the formation of coatings were investigated. The results showed that, with the identical spray parameters, the porosity is higher for the coatings deposited on aluminum than that on stainless steel due to the high thermal transfer ability of the former substrate material. The SEM results revealed that the microstructure of as-prepared coatings could be tailored from the vertical cracked structure to the columnar structure by increasing the substrate surface roughness and their formation mechanisms were discussed. The substrate preheating temperature has an influence on the microstructure of the coatings, especially in the interfacial region. Increasing the substrate temperature is an effective means for reducing the interface defects and for improving the adhesion of the coatings. With the increase in the substrate thickness, the quantity of the vertical cracks in the coatings is reduced and their width becomes narrower.     

Spark plasma sintering of double-walled carbon nanotubes

Bulk samples of double-walled carbon nanotubes are prepared for the first time. The best spark plasma sintering conditions are (1100 °C, 100 MPa). Raman spectroscopy and scanning electron microscopy show that the nanotubes are undamaged. The density is equal to 1.29 g cm⁻³ and the pores are all below 6 nm in diameter. The electrical conductivity is equal to 1650 S cm⁻¹. The transverse fracture strength is equal to 47 MPa.     

Numerical Modeling of Inclusion Behavior in Liquid Metal Processing

Thermomechanical performance of metallic alloys is directly related to the metal cleanliness that has always been a challenge for metallurgists. During liquid metal processing, particles can grow or decrease in size either by mass transfer with the liquid phase or by agglomeration/fragmentation mechanisms. As a function of numerical density of inclusions and of the hydrodynamics of the reactor, different numerical modeling approaches are proposed; in the case of an isolated particle, the Lagrangian technique coupled with a dissolution model is applied, whereas in the opposite case of large inclusion phase concentration, the population balance equation must be solved. Three examples of numerical modeling studies achieved at Institut Jean Lamour are discussed. They illustrate the application of the Lagrangian technique (for isolated exogenous inclusion in titanium bath) and the Eulerian technique without or with the aggregation process: for precipitation and growing of inclusions at the solidification front of a Maraging steel, and for endogenous inclusions in the molten steel bath of a gas-stirred ladle, respectively.     

Ceramic Powder Bed Laser Sintering (CPBLS) on copper-doped hydroxyapatite: Creation of thin (5–50 μm thick) consolidated ceramic patterns

Implants made of ceramics, and more particularly of calcium phosphates (hydroxyapatite: HA, mainly), promoting intimate contact with natural bone are nowadays merging. Addition of copper ions in bio-ceramics is expected to increase the biological compatibilities of bone graft substitutes. Previous works have shown that copper-doped hydroxyapatite (Cu-doped HA) ceramics can be prepared by solid-state sintering between HA and CuO powder mixtures at about 1100 °C; but, copper-substituted HA was found to be metastable leading to apatitic grains and Cu-rich grain boundaries during the sintering process. Ultra-rapid sintering is so needed. Selective laser sintering (SLS) is an additive manufacturing process that possesses the advantage to be based on ultra-fast sintering process under laser irradiation. SLS being used in literature for the application of laser on polymer-ceramic or poymer-metal composites the proper term all along the paper is Ceramic Powder Bed Laser Sintering (CPBLS). To achieve densification of Cu-doped HA ceramics from CPBLS process, one should control the composition/morphology/structure of the powder bed as well as three other important CPBLS parameters: (i) the applied energy from the laser beam, (ii) the laser power and the laser scanning speed, (iii) the distance between two successive lased lines. In this paper, the impact of all the main CPBLS parameters controlling the sintering of dip-coated Cu-doped HA layers on glass substrates is carefully investigated. Possibility of the creation of thin consolidated Cu-doped HA ceramic patterns, using the ultra-fast CPBLS process, is finally shown.     

Hot corrosion behaviour of 7YSZ + Gd2O3 nano-composites in molten salts prepared by spark plasma sintering

This study compares the hot corrosion performance of yttria-stabilised zirconia (7YSZ), and 7YSZ?+?Gd₂O₃ composite samples in the presence of molten mixture of Na₂SO₄?+?V₂O₅ at 1150°C. For 7YSZ, the reaction between NaVO₃ and Y₂O₃ produces YVO₄ and leads the transformation of tetragonal ZrO₂ to monoclinic ZrO₂. A high-density in sintered 7YSZ?+?Gd₂O₃ samples, led minor amounts of monoclinic ZrO₂ and tetragonal GdVO₄ as the hot corrosion products with only traceable amounts of YVO₄, and a stable corroded layer was formed. Due to the synergic effect of doping of zirconia with Gd₂O₃, the 7YSZ?+?Gd₂O₃ sample has a much better hot corrosion crack resistance than 7YSZ.     

Aerobic hydrocarbon oxidation catalyzed by the vanadomolybdophosphate polyoxometalate, H5PV2Mo10O40, supported on mesoporous MCM‐41

The impregnation of H₅PV₂Mo₁₀O₄₀ polyoxometalate onto MCM‐41 and amino‐modified MCM‐41 materials provided mesoporous active catalysts with large surface areas for aerobic hydrocarbon oxidation using isobutyraldehyde as a reducing agent. The results of the oxidation of alkenes and alkanes gave product selectivities similar to those observed in the corresponding homogeneous reaction although catalytic activity was somewhat reduced. Under appropriate experimental conditions there was no leaching and the solid catalyst could be recovered and reused without loss in activity. This revised version was published online in July 2006 with corrections to the Cover Date.     

Cross-influence of membrane polyunsaturated fatty acids and hypoxia-reoxygenation on α- and β-adrenergic function of rat cardiomyocytes

The purpose of the present investigation was to determine whether the beneficial effects of polyunsaturated fatty acids (PUFA) may influence ischemia-reperfusion-induced alterations of myocardial α- and β-adrenoceptor (α-AR, β-AR) responsiveness. This study was carried out using monolayer cultures of neonatal rat ventricular myocytes in a substrate-free, hypoxia-reoxygenation model of ischemia. The cardiomyocytes (CM) were incubated during 4 days in media enriched either with n−6 PUFA (arachidonic acid, AA) or with n−3 PUFA (eicosapentaenoic acid, EPA, and docosahexaenoic acid, DHA). The n−6/n−3 ratio in n−3 CM was close to 1.2, compared to 20.1 in n−6 CM. The contractile parameters of n−6 CM and n−3 CM were similar in basal conditions as well as during hypoxia and reoxygenation. In basal conditions, the phospholipid (PL) enrichment with long chain n−3 PUFA resulted in an increased chronotropic response to isoproterenol (ISO) and to phenylephrine (PHE). After posthypoxic reoxygenation, the chronotropic response to β-AR activation in n−6 CM was significantly enhanced as compared with the control response in normoxia. In opposition, the ISO-induced rise in frequency in n−3 CM in control normoxia and after reoxygenation was similar. In these n−3 CM, the changes in contractile parameters, which accompanied the chronotropic response, were also similar in reoxygenation and in normoxic periods, although the rise in shortening velocity was slightly increased after reoxygenation. In response to PHE addition, only the chronotropic effect of n−6 CM appeared significantly enhanced after hypoxic treatment. These results suggested that increasing n−3 PUFA in PL reduced the increase in α- and β-AR functional responses observed after hypoxia-reoxygenation. This effect may partly account for the assumed cardiac protective effect of n−3 PUFA, through the attenuation of the functional response to catecholamines in the ischemic myocardium.