Adhesion studies of CVD copper metallization

The adhesion of chemical vapor deposition (CVD) Cu thin films to various barriers was observed to improve with a post-deposition anneal or a physical vapor deposition (PVD) Cu flash layer on the barrier before depositing CVD Cu. The ambient exposure of the barrier before the deposition of CVD Cu has been observed to lead to degradation of adhesion in both CVD Cu seed and CVD/PVD Cu high vacuum integrated metallization schemes. The integrated CVD and PVD Cu deposition scheme exhibits better adhesion due to the inherent annealing provided during the PVD deposition which is carried out at temperatures between 300 and 400°C. We have evaluated both qualitative and quantitative tests — tape test, Stud pull test and 4-point bend test — in understanding adhesion and observed that each of these tests give different details of interface breakdown.     

Extraction and analysis of T waves in electrocardiograms during atrial flutter

Analysis of T waves in the ECG is an essential clinical tool for diagnosis, monitoring, and follow-up of patients with heart dysfunction. During atrial flutter, this analysis has been so far limited by the perturbation of flutter waves superimposed over the T wave. This paper presents a method based on missing data interpolation for eliminating flutter waves from the ECG during atrial flutter. To cope with the correlation between atrial and ventricular electrical activations, the CLEAN deconvolution algorithm was applied to reconstruct the spectrum of the atrial component of the ECG from signal segments corresponding to TQ intervals. The locations of these TQ intervals, where the atrial contribution is presumably dominant, were identified iteratively. The algorithm yields the extracted atrial and ventricular contributions to the ECG. Standard T-wave morphology parameters (T-wave amplitude, T peak-T end duration, QT interval) were measured. This technique was validated using synthetic signals, compared to average beat subtraction in a patient with a pacemaker, and tested on pseudo-orthogonal ECGs from patients in atrial flutter. Results demonstrated improvements in accuracy and robustness of T-wave analysis as compared to current clinical practice.     

Ultrasound elastography based on multiscale estimations of regularized displacement fields

Elasticity imaging is based on the measurements of local tissue deformation. The approach to ultrasound elasticity imaging presented in this paper relies on the estimation of dense displacement fields by a coarse-to-fine minimization of an energy function that combines constraints of conservation of echo amplitude and displacement field continuity. The multiscale optimization scheme presents several characteristics aimed at improving and accelerating the convergence of the minimization process. This includes the nonregularized initialization at the coarsest resolution and the use of adaptive configuration spaces. Parameters of the energy model and optimization were adjusted using data obtained from a tissue-like phantom material. Elasticity images from normal in vivo breast tissue were subsequently obtained with these parameters. Introducing a smoothness constraint into motion field estimation helped solve ambiguities due to incoherent motion, leading to elastograms less degraded by decorrelation noise than the ones obtained from correlation-based techniques.     

Residual stress in hydroxyapatite coating: nonlinear analysis and high-energy synchrotron measurements

The thermal deposition of hydroxyapatite (HA) on titanium alloy substrate (Ti-6A1-4V) leads to a structure that has very good osseointegration properties. However, clinical failures have been occasionally reported at the interface between substrate and coating. Lifetime is the main parameter in such prostheses; therefore, in order to improve their quality, it is necessary to evaluate the level of stresses near the interface. The high-energy synchrotron radiation combines the advantages of a bulk analysis and reduced volume of the gauge. The objective of our study was to calculate the residual stress using a nonlinear finite-element model and to measure residual stress level near the interface, in the hydroxyapatite coating and in titanium alloy substrate with a nondestructive and high-resolution experiment. The high-energy synchrotron radiation of the BM16 beam-line at ESRF (Grenoble-France) was used with a resolution of down to 10 micrometers. The experimental measurements validate the results found by means of nonlinear finite-element analysis of the plasma spraying induced stress.     

Upper bounds for blocking probabilities in large multi‐rate loss networks

In this paper, we consider large loss networks with fixed routing and multirate traffic. We use singlelink formulae and standard results on multidimensional Gaussian distributions to obtain upper bounds for blocking probabilities of new calls under light up to critical loading conditions. This is the loading regime of interest for many practical applications such as admission control in ATM networks. The main advantage of our approach is that the complexity does not scale with the size of the system, making it numerically attractive. Comparison with simulation results show that we get good upper bounds. We conclude by discussing the correlation between links in a network.     

Microwave active resonator band-pass filters in various mmic technologies

In this article, two topologies of L-C parallel active resonators are presented. These circuits are realized in MMIC technology, using three transistors which could be MESFET, hemt or HBT. The survey of these resonators shows the possibility, by controling the values of a resistor and/or a capacitor, on the one hand, to tune the resonance frequency of these circuits, and on the other hand, to cancel out their losses so as to obtain negative conductance. Compact, lossless and narrow-band filters are then implemented using previous active resonators. To date, the use of mesfet technology has reduced the synthesis of such active filters in S-band and at X-band low frequencies. Now, however, hemt and HBT technologies allow the extension of their implementation to the whole X-band. This survey is illustrated by the simulated response of a 10 GHz filter with a 500 MHz 3 dB bandwidth. The mmic technology is a 0.2 μm hemt one. The simulated performances of this filter achieve a mean transmission gain of 0. 5 dB, with a reflection loss higher than 10 dB at 10 GHz,     

Cassava retting: Optimisation of a traditional fermentation by an experimental research methodology

Retting, a spontaneous and traditional fermentation of cassava roots in Central Africa, was optimised in terms of time and the quality of the end-product. Optimal conditions were achieved by using an experimental research methodology. Temperature is the most influential factor, with an optimum of 34°C for quicker retting. The roots should be peeled and soaked in water immediately after harvesting to increase the quality of cassava foods. Inoculation of water with juice from a prior retting helps in cassava detoxification but has no influence on the time or the quality of foo-foo. Foo-foo samples had the most favourable organoleptic quality when an incubation temperature of between 28 and 37°C was used. Using optimal conditions, retting time was reduced 3-fold, and foo-foo of high and constant quality could be processed.     

Poly(3-hexylthiophene)/C60 heterojunction solar cells: Implication of morphology on performance and ambipolar charge collection

The performance of heterojunction organic solar cells is critically dependent on the morphology of the donor and acceptor components in the active film. We report results of photovoltaic devices consisting of bilayers and bulk heterojunctions using poly(3-hexylthiophene) (P3HT) and Buckminsterfullerene C₆₀. White light power efficiencies of η2.2% (bulk heterojunction) and 2.6% (bilayer) were measured after a thermal annealing step on completed devices. Optical and structural investigations on non-annealed bilayer thin films indicated a distinct porosity of the spin-coated polymer, which allows C₆₀ to penetrate the P3HT layer and to touch the anode. This resulted for these bilayer solar cells in the experimental observation that electrons were collected predominantly at the cathode after photo-excitation of P3HT, but predominantly at the anode after C₆₀ excitation. A morphological model to explain the ambipolar charge collection phenomenon is proposed.     

Computer-aided method for quantification of cartilage thickness and volume changes using MRI: validation study using a synthetic model

The primary objective of this study was to develop a computer-aided method for the quantification of three-dimensional (3-D) cartilage changes over time in knees with osteoarthritis (OA). We introduced a local coordinate system (LCS) for the femoral and tibial cartilage boundaries that provides a standardized representation of cartilage geometry, thickness, and volume. The LCS can be registered in different data sets from the same patient so that results can be directly compared. Cartilage boundaries are segmented from 3-D magnetic resonance (MR) slices with a semi-automated method and transformed into offset-maps, defined by the LCS. Volumes and thickness are computed from these offset-maps. Further anatomical labeling allows focal volumes to be evaluated in predefined subregions. The accuracy of the automated behavior of the method was assessed, without any human intervention, using realistic, synthetic 3-D MR images of a human knee. The error in thickness evaluation is lower than 0.12 mm for the tibia and femur. Cartilage volumes in anatomical subregions show a coefficient of variation ranging from 0.11% to 0.32%. This method improves noninvasive 3-D analysis of cartilage thickness and volume and is well suited for in vivo follow-up clinical studies of OA knees.     

Plasmonic‐Induced Photon Recycling in Metal Halide Perovskite Solar Cells

Organic–inorganic metal halide perovskite solar cells have emerged in the past few years to promise highly efficient photovoltaic devices at low costs. Here, temperature‐sensitive core–shell Ag@TiO₂ nanoparticles are successfully incorporated into perovskite solar cells through a low‐temperature processing route, boosting the measured device efficiencies up to 16.3%. Experimental evidence is shown and a theoretical model is developed which predicts that the presence of highly polarizable nanoparticles enhances the radiative decay of excitons and increases the reabsorption of emitted radiation, representing a novel photon recycling scheme. The work elucidates the complicated subtle interactions between light and matter in plasmonic photovoltaic composites. Photonic and plasmonic schemes such as this may help to move highly efficient perovskite solar cells closer to the theoretical limiting efficiencies.