Electrical impedance spectroscopy of the human prostate

Tissue electrical impedance is a function of its architecture and has been used to differentiate normal and cancer tissues in a variety of organs including breast, cervix, skin, and bladder. This paper investigates the possibility of differentiating normal and malignant prostate tissue using bioimpedance spectra. A probe was designed to measure impedance spectra over the range of 10 kHz to 1 MHz. The probe was fully characterized using discrete loads and saline solutions of different concentrations. Impedance spectra of five ex vivo prostates were measured in the operating room immediately following radical prostatectomy. Wilcoxon signed-rank tests were used to compare the normal and malignant findings. The impedance probe had a signal-to-noise ratio (SNR) > 84 dB across the entire spectrum and measured a tissue volume of approximately 46 mm(3). At 10 kHz, prostate conductivity (or) ranged from 0.232 S/m to 0.310 S/m for tumor and from 0.238 S/m to 0.901 S/m for normal tissue. At 1 MHz the ranges were 0.301 S/m to 0.488 S/m for tumor and 0.337 S/m to 1.149 S/m for normal. Prostate permittivity (epsilonr) ranged from 6.64 x10(4) to 1.25 x 10(5) for tumor and from 9.08 x 10(4) to 4.49 x 10(5) for normal tissues at 10 kHz. And, at 1 MHz the er ranges were 9.23 x 10(2) to 1.88 x 10(3) for tumor and 1.16 x 10(3) to 2.18 x 10(3) for normal tissue. Both sigma and epsilonr of tumor tissue were found to be significantly lower than that of normal tissue (P < 0.0001). Conductivity and permittivity are both higher in normal prostate tissues than they are in malignant tissue making them suitable parameters for tissue differentiation. This is in agreement with trends observed in other tissues reported in much of the literature. Expanded studies are needed to further validate this finding and to explore the biological mechanism responsible for generating the results.     

Statistical Tolerance Analysis for Assured Analog Test Coverage

Increasing numbers of analog components in today's systems necessitate system level test composition methods that utilize on-chip capabilities rather than solely relying on costly DFT approaches. We outline a tolerance analysis methodology for test signal propagation to be utilized in hierarchical test generation for analog circuits. A detailed justification of this proposed novel tolerance analysis methodology is undertaken by comparing our results with detailed SPICE Monte-Carlo simulation data on several combinations of analog modules. The results of our experiments confirm the high accuracy and efficiency of the proposed tolerance analysis methodology.     

Self‐Compensation in Transparent Conducting F‐Doped SnO2

The factors limiting the conductivity of fluorine‐doped tin dioxide (FTO) produced via atmospheric pressure chemical vapor deposition are investigated. Modeling of the transport properties indicates that the measured Hall effect mobilities are far below the theoretical ionized impurity scattering limit. Significant compensation of donors by acceptors is present with a compensation ratio of 0.5, indicating that for every two donors there is approximately one acceptor. Hybrid density functional theory calculations of defect and impurity formation energies indicate the most probable acceptor‐type defects. The fluorine interstitial defect has the lowest formation energy in the degenerate regime of FTO. Fluorine interstitials act as singly charged acceptors at the high Fermi levels corresponding to degenerately n‐type films. X‐ray photoemission spectroscopy of the fluorine impurities is consistent with the presence of substitutional F_O donors and interstitial F_i in a roughly 2:1 ratio in agreement with the compensation ratio indicated by the transport modeling. Quantitative analysis through Hall effect, X‐ray photoemission spectroscopy, and calibrated secondary ion mass spectrometry further supports the presence of compensating fluorine‐related defects.     

Doping efficiency and energy-level scheme in C60F48-doped zinc–tetraphenylporphyrin films

High resolution synchrotron-based core level spectroscopy was used to examine the energy level alignment at the interface of zinc–tetraphenylporphyrin films doped by the surface acceptor C₆₀F₄₈. Two distinct fluorofullerene charge states were identified, corresponding to ionized and neutral molecules, and their relative concentration as a function of coverage was used to evaluate the probability of occupation of the acceptor lowest unoccupied molecular orbital (LUMO). From an initial acceptor energy of ?0.25 eV, the C₆₀F₄₈ LUMO shifts upwards with coverage due to a doping-induced interfacial dipole potential, and stabilization of the LUMO at an energy 0.45 eV above the Fermi energy was obtained. While the energy difference upon saturation is consistent with the results obtained for other donor–acceptor systems that have been interpreted as Fermi level pinning, the present work shows that the energy offset is a direct consequence of the interplay between Fermi–Dirac statistics in combination with the interfacial dipole potential.     

Glycosidic linkages of legume,grass and cereal straw cell walls before and after extensive degradation by rumen microorganisms

The technique of methylation analysis for the location of glycosidic linkages in cell wall polysaccharides was applied directly (after dry milling in liquid nitrogen) to whole wheat and barley straws, cell wall preparations from early- and late-cut perennial ryegrass and white clover, and their extensively degraded residues recovered from the rumen. The addition of an internal standard, methyl-β-D-allo-pyranose, to milled samples enabled the recovery of partially-methylated sugars to be quantified, and the recovery of parent sugars from methylated material to be compared with values obtained by direct estimation of monosaccharides by the alditol acetate method. Recovery of sugars from methylated samples was generally higher than that predicted by the alditol acetate method, particularly from digested residues. All four samples of Gramineae showed similar proportions of glycosidic linkages in which (1 →4)-linked xylose and glucose units accounted for more than 80% of total identified partially-methylated sugars. The proportions of glycosidic linkages found in digested residues of straws were essentially the same as those found in the parent material. In residues of the more digestible ryegrass there was a two- to three-fold increase in (1→4)-linked xylose units without branch points at the O-2/O-3 positions, the proportions of these branch points being substantially reduced. A corresponding reduction in the proportion of (1→2)-, (1→3)-and terminally-linked arabinose units was also found. The proportion of both (1→4)- and (1→3)-linked glucose units were also reduced in digested residues. These changes were greater in the early-cut than in the late-cut sample. White clover differed from the Gramineae in a number of respects. Galactose units predominantly in the form of (1→4)-, (1→6)- and terminally-linked units, were the major non-cellulosic sugars present. The proportion of all forms of galactose was reduced in digested residues, but (1→6)-linked units appeared more resistant to degradation than (1→4)-linked units. Like ryegrass, the proportion of xylose units increased in digested residues from clover, while the proportion of glucose decreased. The proportion of (1→4)-linked mannose units, initially present at levels ten times as great as in the Gramineae, was also substantially reduced.     

A thyristor- and thermistor-based inrush current limiter for DC-link start-up

Large inrush currents can be harmful to equipment subjected to it and can also disturb other devices through voltage dips. Traditional ways of dealing with large inrush currents include the usage of parasitic elements in the supply, negative temperature coefficient (NTC) resistances and start-up relays. These solutions have several disadvantages among which are a non-negligible standby consumption, using a relay or a compromise between inrush current and load losses using an NTC. This paper proposes a solution which solves these disadvantages. The proposed circuit uses a semi-controlled bridge rectifier requiring a very low standby power consumption and is capable of withstanding grid interruptions. Moreover, it is designed to power on only when the load is not too heavy. This is accomplished by the use of positive temperature coefficient thermistors. The presented solution can be used for DC-link start-up circuits in applications with a power range from several watts up to a few kilowatts and it is particularly suitable for on-board battery chargers designed for electrical vehicles.     

Design of Engineered Elastomeric Substrate for Stretchable Active Devices and Sensors

In the field of flexible electronics, emerging applications require biocompatible and unobtrusive devices, which can withstand different modes of mechanical deformation and achieve low complexity in the fabrication process. Here, the fabrication of a mesa‐shaped elastomeric substrate, supporting thin‐film transistors (TFTs) and logic circuits (inverters), is reported. High‐relief structures are designed to minimize the strain experienced by the electronics, which are fabricated directly on the pillars' surface. In this design configuration, devices based on amorphous indium‐gallium‐zinc‐oxide can withstand different modes of deformation. Bending, stretching, and twisting experiments up to 6 mm radius, 20% uniaxial strain, and 180° global twisting, respectively, are performed to show stable electrical performance of the TFTs. Similarly, a fully integrated digital inverter is tested while stretched up to 20% elongation. As a proof of the versatility of mesa‐shaped geometry, a biocompatible and stretchable sensor for temperature mapping is also realized. Using pectin, which is a temperature‐sensitive material present in plant cells, the response of the sensor shows current modulation from 13 to 28 °C and functionality up to 15% strain. These results demonstrate the performance of highly flexible electronics for a broad variety of applications, including smart skin and health monitoring.     

Direction finding using data-supported optimization

A novel data-supported optimization technique for maximum likelihood (ML) direction-of-arrival estimation is proposed. The essence of our approach is to optimize the likelihood function at certaindata-supported points obtained by a resampled root-MUSIC procedure. These points are shown to comprise a small but representative subset of all possible searching points and contain enough information for solving the ML problem.This work was supported in part by grants from the National Sciences and Engineering Research Council of Canada (NSERC), Ministry of Energy, Science and Technology (MEST) of Ontario, Communications and Information Technology Ontario (CITO), and by the Senior Individual Grant Program of the Swedish Foundation for Strategic Research.     

Side‐Chain Engineering on Dopant‐Free Hole‐Transporting Polymers toward Highly Efficient Perovskite Solar Cells (20.19%)

A variety of dopant‐free hole‐transporting materials (HTMs) is developed to serve as alternatives to the typical dopant‐treated ones; however, their photovoltaic performance still falls far behind. In this work, the side chain of a polymeric HTM is engineered by partially introducing diethylene glycol (DEG) groups in order to simultaneously optimize the properties of both the bulk of the HTM layer and the HTM/perovskite interface. The intermolecular π–π stacking interaction in the HTM layer is unexpectedly weakened after the incorporation of DEG groups, whereas the lamellar packing interaction is strengthened. A doubled hole mobility is obtained when 3% of the DEG groups replace the original alkyl side chains, and a champion power conversion efficiency (PCE) of 20.19% (certified: 20.10%) is then achieved, which is the first report of values over 20% for dopant‐free organic HTMs. The device maintains 92.25% of its initial PCE after storing at ambient atmosphere for 30 d, which should be due to the enhanced hydrophobicity of the HTM film.