Rock salt dilatancy boundary from combined acoustic emission and triaxial compression tests

This paper presents an experimental investigation of rock salt dilatancy boundary based on combined acoustic emission and triaxial compression tests carried out on the rock salt samples from the Asse Salt Mine, Germany. The experimental results were evaluated to determine the dilatancy boundary under specified stress, stress loading rate and pore pressure. Pore volume changes caused by deviatoric stresses were measured during triaxial compression tests. The dilatancy boundary was then determined from the maximum compression on a stress–strain curve which separates the compression and dilatancy regions. Variations in acoustic emissions that occur during microcrack development under triaxial compression were recorded with ten sensors mounted on the outer surface of the cylindrical samples. A spontaneous increase observed in the cumulative number of acoustic events is consistent with the dilatancy boundary determined from the minimum pore volume. It is confirmed that the dilatancy boundary depends on both stress loading rate and pore pressure. The dilatancy boundary slightly decreases with increasing the loading rate, but increases with increasing the minor normal stress. High pore pressures accelerate the dilatancy. A Biot coefficient of 0.25 for Asse rock salt was determined from the dilatancy boundary. An analysis of two-dimensional (2D) fractal dimensions determined for several samples shows that the samples with smaller dimensions have slightly higher dilatancy boundaries. The dilatancy boundary values of Asse rock salt are lower than those reported for crystalline rocks, although both rock types show similar dilatancy behaviour.     

Mechanical properties and morphology of nylon‐6 hybrid composites

In this investigation, the influence of filler type and filler content on the mechanical properties of nylon‐6 is investigated. The mineral fillers were selected on the basis of their shape and size: flake‐like kaolin and talc, spherical glass beads or fibrous wollastonite. These fillers were added to nylon‐6 individually or in mixed combinations. They were added at different percentages varying between 10 and 30% w/w. Samples of the composites were prepared by the injection moulding process. Uniaxial tensile, Izod impact and flexural tests were carried out. Tensile strength, elongation at break, modulus of elasticity and impact energy were obtained and compared. In case of single fillers the results showed that the tensile strength, modulus of elasticity and their flexural values for nylon‐6 composite improve with the increase in filler content while mixed compounds showed no significant changes above 15% + 15% w/w filler. However, for single and mixed filler up to 10% w/w, the impact strength and maximum elongation at break showed significant decrease. In general, the maximum improvement in mechanical the addition of 10–15% w/w filler. Copyright © 2003 Society of Chemical Industry     

A comparative study on the diagnosis of maedi-visna infection in serum and colostrum samples using agar gel immunodiffusion (AGID) technique

Serum/colostrum pairs were collected from 245 ewes in 6 sheep herds which had been determined previously to be infected with MV virus and were tested against maedi-visna infection using AGID test. Positive rates were detected as 3.8-41.2% in tested flocks. Serum and colostrum samples obtained from 53 sheep were positive for MV virus specific antibodies by AGID test. 16 colostrum samples were negative although serum samples obtained from the same animals were found to be positive for MV antibodies. Of the 245 sera and colostrum pairs tested, there was total agreement of results (+ or -) in 229 and disagreement in the results with the other 16 serum/colostrum pairs. Of the latter, all serum samples were positive and all colostrum samples were negative for MV antibodies. This study compared colostrum and serum samples for the determination of MV antibodies using AGID test under field conditions on naturally infected animals and on healthy animals. The results show that colostrum antibodies can be detected using AGID test and that colostrum is a reliable material to determine anti-MV virus antibodies. The procedure can be used for herd diagnosis.     

Mice lacking the IFN-gamma receptor have impaired ability to resolve a lung eosinophilic inflammatory response associated with a prolonged capacity of T cells to exhibit a Th2 cytokine profile

To investigate the modulatory role of IFN-gamma on the induction and maintenance of Th2 mucosal immunity in vivo, experiments were performed in mice lacking the IFN-gamma R. Aerosol OVA challenge of immunized wild-type mice resulted in an infiltration of eosinophils into the lung, associated with the ex vivo production of Th2 cytokines (IL-4 and IL-5) from purified lung Thy1.2+ cells stimulated via the CD3/TCR complex. However, while immunized IFN-gamma R-deficient mice exhibited elevated levels of IgE, IgG1, and reduced levels of IgG2a compared with wild-type mice, there was no difference in the recruitment of eosinophils into the lung or the production of IL-4 and IL-5 from lung T cells on day 3. In contrast, up to 2 mo after a single Ag challenge, eosinophils were still present in the lungs of IFN-gamma R-deficient, but not wild-type, mice. Likewise, lung-derived T cells from IFN-gamma R-deficient mice produced higher levels of IL-4 and IL-5, both at 1 and 2 mo after OVA challenge compared with T cells from wild-type mice. We conclude that endogenous IFN-gamma regulates the humoral isotype Ab pattern, but does not modulate the commitment of T cells to a Th2 phenotype in vivo or the acute infiltration of eosinophils to the lung. However, in the absence of IFN-gamma-mediated signaling, there is a transition from a spontaneously resolving to a persisting eosinophilic inflammation of the lungs, associated with a sustained capacity of lung T cells to secrete a Th2 cytokine profile.     

Immunohistochemical analysis of mycosis fungoides on paraffin-embedded tissue sections

Mycosis fungoides (MF) is typically characterized by dermal and epidermal infiltration of T lymphocytes with a helper/inducer phenotype. Immunophenotypic analysis of such cases was traditionally performed by flow cytometry or immunohistochemistry on cryostat sections. With the advent of new monoclonal antibodies developed against T-cell antigens, including CD3, CD4, CD5, and CD8, it is now possible to immunophenotype T-cell subpopulations in paraffin-embedded tissues. To investigate the potential use of these antibodies for the evaluation of cutaneous lesions, 35 specimens (34 skin and 1 lymph node) from 29 patients with MF were retrospectively reviewed and immunophenotyped in paraffin sections with antibodies to CD3 (T-cell CD3), CD4 (NCL-CD4-1F6), CD5 (NCL-CD5-4C7), CD8 (CD8/144B), and CD20 (L26). Epidermal and dermal distribution of T and B cells were analyzed, and we assessed the ratios of CD4+ to CD8+ T cells. All of our 35 cases demonstrated a predominant CD3+ T-cell population. In 32 cases, the neoplastic cells expressed CD3, CD4, and CD5 consistent with a T-helper/inducer phenotype. In three cutaneous cases, the neoplastic CD4+ T cells showed minimal or absent expression of CD5, indicating an aberrant phenotype. In the majority of cases, minimal CD8+ T cells were present in the background, but in four cases, the CD4:CD8 ratios were 2:1 or less. Thirty-two cutaneous cases demonstrated epidermotropism exclusively by CD4+ T cells; one case showed both CD4+ and CD8+ T cells. In 17 cutaneous cases, scattered dermal CD20+ B cells were found individually or in small clusters within the background surrounding the neoplastic infiltrates. We concluded, therefore, that the immunophenotypic analysis of T-cell subpopulations using monoclonal antibodies of CD3, CD4, CD5, and CD8 was useful for histologic evaluation and confirmation of MF lesions in paraffin-embedded tissue. These antibodies might also provide an effective method of immunophenotyping other neoplastic and non-neoplastic T-cell populations in paraffin-embedded tissues.     

Solubility of chlorine in aqueous hydrochloric acid solutions

The solubility of chlorine in aqueous hydrochloric acid solutions was studied. The effects of HCl concentration and temperature on the solubility were evaluated, and the thermodynamic parameters of the dissolution were calculated. It was found that the solubility isotherms had a minimum at about 0.5M HCl concentration at all the temperatures studied and that solubility decreased with the increase of temperature at all the HCl concentration range investigated.     

Leaching kinetics of colemanite by aqueous EDTA solutions

The dissolution kinetics of colemanite, a boron-containing mineral, in aqueous disodium EDTA solutions were studied. The effects of concentration and pH of the solution, particle size, and temperature were examined. A decrease in pH and particle size increased the dissolution rate, while an increase in the concentration of the solution and temperature increased the rate. The activation energy and pre-exponential factor were calculated as 50.6 kJ mol^-1 and 5.14 x 10⁷ m s^-1, respectively. Mahir Alkan, Assistant Professor, formerly with Atatürk University, Kazim Karabekir Faculty of Education     

Influence of Radiation‐Induced Grafting Process on Mechanical Properties of ETFE‐Based Membranes for Fuel Cells

The mechanical stability is, in addition to thermal and chemical stability, a primary requirement of polymer electrolyte membranes in fuel cells. In this study, the impact of grafting parameters and preparation steps on stress–strain properties of ETFE‐based proton conducting membranes, prepared by radiation‐induced grafting and subsequent sulphonation, was studied. No significant change in the mechanical properties of the ETFE base film was observed below an irradiation dose of 50 kGy. It was shown that the elongation at break decreases with increasing both the crosslinker concentration and graft level (GL). However, the tensile strength was positively affected by the crosslinker concentration. Yield strength and modulus of elasticity are almost unaffected by the introduction of crosslinker. Interestingly, yield strength and modulus of elasticity increase gradually with GL without noticeable change of the inherent crystallinity of grafted films. The most brittle membranes are obtained via the combination of high GL and crosslinker concentration. The optimised ETFE‐based membrane (GL of ∼25%, 5% DVB v/v), shows mechanical properties superior to those of Nafion® 112 membrane. The obtained results were correlated qualitatively to the other ex situ properties, including crystallinity, thermal properties and water uptake of the grafted membranes.     

新的分析仪器在中国纺织厂的应用经验

<正>1介绍质量的许多定义之一是产品的某些属性满足客户或是用户的需要,对纺织工艺来说,质量常常通过纤维、纱线或是织物的不同属性来定义,这些属性必须得到系统的控制。     

Adsorption of cationic polyacrylamide onto sepiolite

The adsorption of PAM onto sepiolite from aqueous solutions has been investigated systematically as a function of some parameters such as calcination temperature of sepiolite, pH, ionic strength and temperature. The adsorption of cationic polyacrylamide (PAM) increases with pH from 5.50 to 11.00, temperature from 25 to 55 degrees C and ionic strength from 0 to 0.1molL(-1). The sepiolite sample calcined at 200 degrees C has a higher adsorption capacity than the other calcined samples. Adsorption isotherms of PAM onto sepiolite have been determined and correlated with common isotherm equations such as Langmuir and Freundlich isotherm models. The Langmuir isotherm model appeared to fit the isotherm data better than the Freundlich isotherm model. The physical properties of this adsorbent are consistent with the parameters obtained from the isotherm equations. The zeta potentials of sepiolite suspensions have been measured in aqueous solutions of NaCl and different PAM concentrations and pH. From the experimental results: (i) pH strongly alters the zeta potential of sepiolite, (ii) sepiolite has an isoelectric point at about pH 6.6 in water and about pH 8 in 250mgL(-1) PAM concentration, (iii) PAM changes the interface charge from negative to positive for sepiolite. Effect of temperature on adsorption has been quantified by calculating various thermodynamic parameters such as Gibbs free energy, enthalpy and entropy. The dimensionless separation factor (R(L)) has shown that sepiolite can be used for adsorption of PAM from aqueous solutions.