Correction to: EDVWDD: Event‑Driven Virtual Wheel‑based Data Dissemination for Mobile Sink‑Enabled Wireless Sensor Networks

The Journal of Supercomputing - A correction to this paper has been published: https://doi.org/10.1007/s11227-021-03790-9     

High power and low cross‐polarization microstrip patch array antenna at S‐band

This article reports the design and development of high power, low cross‐polarization, and high efficiency circularly polarized microstrip patch array antenna at S‐band, proposed for Indian Regional Navigation Satellite System payload. A novel feeding mechanism for truncated corner square patch based on square coaxial line for broadband impedance matching is discussed. Sequential rotation scheme for axial ratio improvement in an array is implemented. High power handling margins in critical regions of square coaxial line for multipaction breakdown is brought out. Measured 19 dB return loss bandwidth of array antenna is 15.6%. Axial ratio of 0.78 dB over global coverage is achieved in the desired frequency band of operation. © 2011 Wiley Periodicals, Inc. Int J RF and Microwave CAE, 2012.     

DDFSGEN

This paper presents a functional compiler for the automatic design of Direct Digital Frequency Synthesizer (DDFS) integrated circuits (ICs) using a ROM based table look-up architecture. The compiler allows the user to specify high-level specifications such as the acceptable spurious response and it generates the IC architecture, floorplan, and layout. To construct the layout for different specifications, a library of parameterized macrocells has been developed in 1.2 m CMOS technology.A test chip with a quadrature DDFS module has been generated, using the compiler, and fabricated. The chip has two input signals: one is for frequency control while the other is for phase initialization. Input and output word lengths are 16 bits and 6 bits respectively. The chip complexity is approximately 12,000 transistors (DDFS core) and the die size is 4.8×2.9mm ². A maximum sample rate of 80 MHz has been attained implying a maximum sine (cosine) output frequency of 40 MHz and a frequency resolution of 1.22 kHz. The maximum spurious level measured is –46 dB.     

Finding trajectories of feature points in a monocular image sequence

Identifying the same physical point in more than one image, the correspondence problem, is vital in motion analysis. Most research for establishing correspondence uses only two frames of a sequence to solve this problem. By using a sequence of frames, it is possible to exploit the fact that due to inertia the motion of an object cannot change instantaneously. By using smoothness of motion, it is possible to solve the correspondence problem for arbitrary motion of several nonrigid objects in a scene. We formulate the correspondence problem as an optimization problem and propose an iterative algorithm to find trajectories of points in a monocular image sequence. A modified form of this algorithm is useful in case of occlusion also. We demonstrate the efficacy of this approach considering synthetic, laboratory, and real scenes.     

Sparse decompositions for exploratory pattern analysis

We define and verify the utility of a pattern analysis procedure called sparse decomposition. This technique involves sequentially ``peeling' sparse subsets of patterns from a pattern set, where sparse subsets are sets of patterns which possess a certain degree of regularity or compactness as measured by a compactness measure c. If this is repeated until all patterns are deleted, then the sequence of decomposition ``layers' derived by this procedure provides a wealth of information from which inferences about the original pattern set may be made. A statistic P is derived from this information and is shown to be powerful in detecting clustering tendency for data in reasonably compact sampling windows. The test is applied to both synthetic and real data.     

Breakdown Trade-Off Relation of Mechanical Properties via Micro-alloying in Mg–Mn Alloys

The impact of micro-alloying on tensile behavior at strain rates in various ranges is examined using five types of extruded Mg-0.3 at. pct Mn–0.1 at. pct X ternary alloys, where X is selected as a common element, Al, Li, Sn, Y or Zn. Microstructural observations reveal that the average grain size of these extruded alloys is between 1 and 3 μm, and these micro-alloying elements segregate at grain boundaries. In room temperature tensile and compression tests, these results show that the mechanical properties and deformation behavior are influenced by the micro-alloying element, even as a small addition of 0.1 at. pct. Mg–Mn–Y and Mg–Mn-Zn alloys show higher strength and smaller strain rate sensitivity (m-value) among the present alloys, owing to the rate-controlling mechanism as dislocation slip. On the other hand, the Mg–Mn–Li alloy exhibits the largest elongation to failure in tension and the highest strain rate sensitivity, associated with high contribution of grain boundary sliding to deformation. These differences are due to the grain boundary segregation of the micro-alloying elements. Compared to the common Mg alloys, the present ternary alloys also show a trade-off relationship between strength and ductility, which is similar to that of the well-known Mg alloys; however, these properties of the Mg–Mn system ternary alloys could be controlled via the type of micro-alloying elements with a chemical content of 0.1 at. pct.

     

Catalytic oxidation of methanol over molybdenum oxide–tungsten oxide

The vapour phase oxidation of methanol to formaldehyde over molybdenum oxide, tungsten oxide and their mixtures has been investigated in an integral flow reactor at atmospheric pressure. The effect of several process variables on the conversion and yield were determined. A high conversion of 95.6% methanol with nearly 95% selectivity was obtained at 430°C. A rate expression has been derived from the kinetics of the reaction.     

Geomorphic diversity as a river management tool and its application to the Ganga River,India

Understanding of geomorphic processes and the determination of geomorphic diversity in catchments are prerequisites for the sustainable rehabilitation of river systems and for reach‐scale assessment of river health. The Ganga River system in India is a large, complex system consisting of several long tributaries, some >1,000 km, originating from 2 distinct hinterlands—the Himalaya to the north and the cratons to the south. Traversing through a diverse climatic regime across the Plain and through precipitation zones ranging from 600 mm/year near Delhi to 1,200 mm/year in the eastern plains, the Ganga River system has formed very diverse landform assemblages in 3 major geomorphic domains. We have recognized 10 different river classes for the trunk river from Gangotri (source) to Farakka (upstream of its confluence with the Brahmaputra) based on (a) landscape setting, (b) channel and active floodplain properties, and (c) channel planform parameters. The mountainous stretch is characterized by steep valleys and bedrock channels and is dominated by large‐scale sediment production and transport through hill slope processes. The alluvial part of the river is characterized by 8 different river classes of varying reach lengths (60–300 km) many of which show sharp transitions in landscape setting. We have highlighted the application of this approach for the assessment of habitat suitability, environmental flows, and flood risk all of which have been significantly modified during the last few decades due to large‐scale anthropogenic disturbances. We suggest that the diversity embedded in this geomorphic framework can be useful for developing a sustainable river management programme to “work with” the contemporary character and behaviour of rivers.     

2-DOF vibratory gyroscope fabricated by SU-8 based UV-LIGA process

This paper reports fabrication of 2-DOF vibratory gyroscope using SU-8 based UV-LIGA process. The device structure is designed to be symmetrical in order to match the resonance frequencies of drive and sense mode oscillators and also to minimize their relative temperature dependent drift. The overall arrangement is such that the two vibration modes do not affect each other and therefore, mechanical decoupling is achieved which helps in minimizing bias drift. The design is optimized to be compatible with the UV-LIGA process having 10 μm thick electroformed nickel as structural layer. Photolithography to create 11 μm thick SU-8 molds for electroforming sacrificial copper and structural nickel layer is optimized using multiple exposure technique that ensures near vertical side walls. Since the highly cross-linked SU-8 remaining after development is difficult to remove reliably from high aspect ratio structures without damage or alteration to the electroformed metals, a 2.45 GHz MW plasma etching process is developed with CF₄/O₂ mixes. The fabricated device is checked for off-plane misalignment between the stationary and movable comb fingers using white light interferometry and it is found to be almost negligible. Also, the prototype device is characterized for amplitude and phase spectral responses using Polytec MSA-500 Micro System Analyzer. The drive and sense mode resonance frequencies are observed at 7.3 and 7.1 kHz respectively against the mode matched designed frequency of 7.5 kHz.