Effect of a Small Amount of Synthetic Fiber on Performance of Biocarbon-Filled Nylon-Based Hybrid Biocomposites

Advanced hybrid biocomposites are engineered from nylon 6, waste wood biosourced carbon (biocarbon) with a low content of synthetic fiber for lightweight auto-parts uses. The novel engineering process through direct injection molding of only 2 wt% synthetic fibers in the form of masterbatch with 20 wt% biocarbon, results outstanding performance of the resulting nylon biocomposites. Such uniquely developed biocomposites show tensile strength of 105 MPa and tensile modulus of 5.14 GPa with a remarkable heat deflection temperature (HDT) of 206 °C. The direct injection molding of synthetic fiber retains the length ≈3 times higher as compared to traditional extrusion and injection molding; resulting greater degree of entanglement and composite reinforcement effectiveness in the hybrid biocomposites. Highly dimensionally stable nylon 6 biocomposites with a very low coefficient of linear thermal expansion results through reinforcing ability of the sustainable biocarbon and small amount of synthetic fiber.     

High temperature bending creep behavior of a multi-cation doped α/β-SiAlON composite

SiAlON ceramics with high hardness and high toughness can be made through designing α/β-SiAlON composites. An important advantage of α-SiAlON phase is that the amount of intergranular phase is reduced by the transient liquid phase being absorbed into the matrix of α-SiAlON phase during sintering. But, the thermal stability of the α-SiAlON phase is an important concern for α/β-SiAlON composites especially at high temperatures. The use of different types of single or multiple cations during fabrication directly affects resultant microstructures and mechanical behavior of α/β-SiAlON composites. In this study, the creep behavior of a multi-cation (Y, Sm and Ca) doped α/β-SiAlON composite, in which aluminum-containing nitrogen melilite solid solution phase was designed as intergranular phase, was investigated by four-point bending creep tests under stresses from 50 to 150 MPa and at temperatures from 1300 °C to 1400 °C in air. The stress exponent was determined to be 1.6 ± 0.13 at 1400 °C and the creep activation energy was calculated to be 692 ± 37 kJ/mol⁻¹. Grain boundary sliding coupled with diffusion was identified as the rate-controlling creep mechanism for the α/β-SiAlON composite.     

Measurement invariance of the Gifted Rating Scales—School Form across five cultural groups.

This study examined measurement invariance of the Gifted Rating Scales—School Form (GRS–S) across the United States, Puerto Rico, China, South Korea, and Turkey, using multigroup confirmatory factor analysis. A total of 1,817 students were rated by 287 teachers using either translated versions of GRS–S or the original English GRS–S. Results indicate a similar factor structure for the GRS–S across the five locations; six factors with each of the 72 items equivalently loaded to the same latent variable across groups. The metric invariance test and the factor variance and covariance invariance tests reveal that the patterns of factor loadings and the factor variances and covariances are invariant across the five groups. Moreover, the scalar invariance test indicates that item means are equivalent across the groups. These results suggest that the GRS–S has intercultural utility and can be similarly interpreted. Implications and limitations of the present research for gifted identification are discussed. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Tribological Behavior of TiAlN,AlTiN, and AlCrN Coatings at Boundary Lubricating Condition

In this study, ~?3.5 µm thick multilayer titanium alumina nitride (TiAlN), alumina titanium nitride (AlTiN), and alumina chromium nitride (AlCrN) coatings were deposited on the H13 steel surface by cathodic arc physical vapor deposition (CAPVD) method. The tribological performance of the coatings was evaluated by a tribometer at boundary lubrication condition. Then, coating surfaces were observed by optical microscope, optical profilometer, and atomic force microscope to evaluate the morphological changes, wear volumes, and tribofilm thickness. Also, scanning electron microscopy (energy dispersive X-ray) and X-ray photoelectron spectrometry analyses were applied to coating surfaces for the tribochemical evolution of the tribofilm. Results showed that AlCrN coating performed the best tribological behavior at boundary lubricated condition, when compared to TiAlN and AlTiN coatings and it can be used as a wear resistant cam tappet coating in internal combustion engines.     

Polyamide 6–Cellulose Composites: Effect of Cellulose Composition on Melt Rheology and Crystallization Behavior

Melt rheology and crystallization behavior of polyamide 6 (PA 6) and microcrystalline cellulose (MCC) composites were systematically studied in this research. The incorporation of MCC into the PA 6 matrix resulted in higher complex viscosities (|η*|), storage modulus (G′), and shear viscosities than those of neat PA 6, especially at low frequencies. The orientation of rigid molecular chains in the composites introduced by the addition of MCC induced a strong shear thinning behavior with an increase in MCC loading. The non‐isothermal crystallization kinetics of PA 6 and MCC composites were investigated by differential scanning calorimetry. The Avrami and Tobin model were applied to describe the process of non‐isothermal crystallization and to determine the crystallization parameters of the composites. Analysis of the crystallization kinetics indicated that the Avrami (n_a) and Tobin exponent (n_t) was altered by the MCC. It was also found that the Avrami and Tobin equations fit the empirical data well. POLYM. ENG. SCI., 54:739–746, 2014. © 2013 Society of Plastics Engineers     

Effect of various additives to marinating baths on some properties of cattle meat

Longissimus dorsi (LD) muscles obtained from young bull carcasses (Holstein Friesian) were marinated, using solutions containing 0.5% sodium tripolyphosphate (STP), 0.5% dicalciumhydrogen phosphate (CHP) and 0.5% citric acid (CA). All solutions, including a blank, contained 2% NaCl. Expressible moisture, cooking loss, marinade uptake, area gain (increase in slice size), colour coordinate values (L*, a*, b*), marinade and meat pH, and the textural properties of samples were evaluated. Marinating with STP and CHP solutions resulted lower cooking losses. Marinade uptake and area gain were lower for control steaks and steaks marinated with the CA solution. The highest lightness was found in steaks marinated with the CA solution. Steaks marinated with STP and CHP solutions were darker. The CA solution resulted in yellowness of steaks. All treatments significantly affected hardness, chewiness and resilience values of steaks. The lowest hardness value was found in steaks marinated with CA. STP and CHP treatments also improved tenderness.     

Poly(ε‐caprolactone) composites containing gentamicin‐loaded β‐tricalcium phosphate/gelatin microspheres as bone tissue supports

In this work, novel antibacterial composites were prepared by using poly(ε‐caprolactone) (PCL) as the main matrix material, and gentamicin‐loaded microspheres composed of β‐tricalcium phosphate (β‐TCP) and gelatin. The purpose is to use this biodegradable material as a support for bone tissue. This composite system is expected to enhance bone regeneration by the presence of β‐TCP and prevent a possible infection that might occur around the defected bone region by the release of gentamicin. The effects of the ratio of the β‐TCP/gelatin microspheres on the morphological, mechanical, and degradation properties of composite films as well as in vitro antibiotic release and antibacterial activities against Escherichia coli and Staphylococcus aureus were investigated. The results showed that the composites of PCL and β‐TCP/gelatin microspheres had antibacterial activities for both bacteria. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Utilization of a series resonant DC link for a DC motor drive

A high-frequency series resonant DC link converter is utilized as a DC motor drive. This system generates a resonant current in a series link, and switching is done at zero current instants, reducing switching losses to a minimum value. A pulse density modulation (PDM) strategy, utilizing a current rectangular loop and an external motor speed feedback loop, controls the resonant converter. A sinusoidal input fundamental current and nearly unity input power factor can be observed in different load conditions. The overall characteristics of the system, including such variables as maximum power, input current, start up, and transient responses, are presented by digital simulation and were verified on an actual prototype system