An investigation of the ordered DO19 phase formation in the Ti-Al system

For the Ti-rich, Ti-AI system, the- and- ₂ phase boundaries have been obtained through differential thermal analysis for alloy compositions ranging from 10.2 to 25.2 at% Al (6 to 16 wt% Al). It has been shown that in the above mentioned composition range, a metastable disordered-phase can be quenched in. This metastable then transforms to the ordered ₂(DO)₁₉ phase upon heating and/or isothermal ageing. It has also been observed that the kinetics of this ordering phenomenon is composition dependent.     

Structure and properties of some vegetable fibres

The stress-strain curves for pineapple leaf fibre have been analysed. Ultimate tensile strength (UTS), initial modulus (YM), average modulus (AM) and elongation of fibres have been calculated as functions of fibre diameter test length and test speed. UTS, YM, and elongation lie in the range of 362 to 748 MN m^–2, 25 to 36 GN m^–2, and 2.0 to 2.8%, respectively for fibres of diameters ranging from 45 to 205m. UTS Was found to decrease with increasing test lengths in the range 15 to 65 mm. Various mechanical parameters show marginal changes with change in speed of testing in the range of 1 to 50 mm min^–1. The above results are explained on the basis of structural variables of the fibre. Scanning electron microscope studies of the fibres reveal that the failure of the fibres is mainly due to large defect content of the fibre bo1h along the fibre and through the cross-section, The crack is always initiated by the defective cells and further aggravated by the weak bonding material between the cells.     

The design,analysis, and cost estimation of a generic adder and subtractor using the layered T (LT) logic reduction methodology with a quantum-dot cellular-automata-based approach

The quantum-dot cellular automata (QCA) is considered to be one of the ground-breaking nanotechnologies developed over the last two decades. A layered T (LT) logic cell library is constructed herein, and the methodology is extended to generic adder and subtractor module designs. The two proposed algorithms lead to more efficient QCA layout designs for an n-bit ripple carry adder (RCA) and subtractor based on an effective clock zone assignment approach. The suggested one-, four-, and eight-bit RCAs and subtractors surpass most of their existing counterparts by offering lower effective area and cell complexity. A comparative analysis is presented regarding the complexity, irreversible power dissipation, and Cost_α of the proposed n-bit layouts from a cost estimation purview.

     

Growth of part-through thickness fatigue cracks in sheet polymethylmethacrylate

Fatigue growth data has been obtained for part-through thickness cracks in sheet specimens of polymethylmethacrylate subjected to cyclic tension. Statistical techniques are used to examine the usefulness of linear elastic fracture mechanics for correlating this part-through thickness crack growth data with throughthickness data published previously.     

Preparation and characterization of low-halogen and nonhalgoen fire-resistant low-smoke (FRLS) cable sheathing compound from blends of functionalized polyolefins and PVC

An attempt is made to develop a novel series of cable sheathing compounds with variation in chlorine content and sufficient fire retardance and unique low-smoke characteristics. These are prepared by blending PVC and functionalized polyolefins in different compositions. PE and EPDM have been functionalized by grafting dibutyl maleate (DBM) using DCP as initiator. FRLS compounds made from PVC-functionalized polyolefin blends possess the special characteristics of low-smoke, low-acid-gas generation, increased fire retardance, and improved volume resistivity, which are much better in comparison with a typical PVC sheathing compound. Thermoplastic elastomer (TPE) based nonhalogen FRLS compounds are also reported. The mechanisms for grafting, polymer-polymer and polymer-filler interactions have been presented.     

Anisotropy of X-ray structural parameters of the three phase model in cellulose I

Anisotropy of X-ray structural parameters of the three phase model proposed by Mitra and Mukherjee (ref.2), has been investigated in the case of cellulose fibres of ramie, hemp and jute. The structural parameters have been determined separately from each of the observable equatorial reflections. It has been found that the parameter degree of crystallinity as defined in the model is in fact anisotropic at least in the samples studied. The parameter degree of paracrystallinity introduced by Mitra and Mukherjee was also found to be anisotropic. Several important correlations between the structural parameters have been drawn. It has been observed, in agreement with the recent findings of Hosemann and Balta Calleja (ref.10) that the greater the paracrystalline distortion, the smaller the ‘paracrystallite size’.     

Tool path generation framework for accurate manufacture of complex 3D sheet metal parts using single point incremental forming

The prototyping of complex sheet metal parts using single point incremental forming (SPIF) requires the generation of optimal tool paths and/or tool path sequences that ensure that the formed part is within geometric design specifications. The presence of a multitude of features on complex parts leads to multiple inaccuracy inducing phenomena occurring simultaneously due to interactions between the features. This paper proposes a network analysis methodology using topological conceptual graphs to capture the effects of different phenomena on the final accuracy of a sheet metal part manufactured by SPIF. Using this framework optimized tool paths can be generated that compensate for the inaccuracy inducing behavior. Tool path generation algorithms to create partial tool paths that account for the accuracy of specific features in the part based on the proposed framework are also presented. Finally, the creation of integrated tool paths maintaining complementarity between tool paths and desired continuity behavior using non-uniform cubic B-splines is illustrated. A number of case studies demonstrating the applicability of the integrated framework are discussed, where the maximum deviations in the part are significantly reduced and the average absolute deviations for the complete part are brought down to less than 0.5 mm.     

Pixel rearrangement based statistical restoration scheme reducing embedding noise

In this paper, a block based steganographic algorithm has been proposed where a sequence of secret bits are embedded into a set of pixels by rearranging the pixel locations. This algorithm has been devised as an improvement over existing statistical restoration based algorithms in order to reduce the additive noise which occurs due to embedding. It is shown that the proposed scheme substantially reduces the additive noise compared to existing statistical restoration based schemes.     

Processing and physical properties of native grass-reinforced biocomposites

Big blue stem grass fiber-reinforced high density polyethylene powder biocomposites were fabricated using two separate processing schemes: (1) by compounding biofiber with the thermoplastic powder in an extruder and subsequently injection molding the extrusion pellets and (2) by combining biofiber and the powder thermoplastic powder using a modified sheet molding compounding (SMC) line and subsequently compression molding the sheet material. The physical properties including storage modulus, heat deflection temperature (HDT), notched Izod impact strength, and morphology were evaluated with dynamic mechanical analysis, Izod impact strength measurement, and microscopy observation. It was found that compression-molded specimens achieved similar modulus values to injection molded specimens for grass-reinforced high density polyethylene (HDPE) composites. The stiffness of the compression-molded specimens is related to the consolidation state of the samples, which depends on compression molding conditions such as temperature, pressure, and mold type. Compression-molded specimens exhibited a higher HDT and notched Izod impact strength compared to injection-molded samples. Grass fiber-reinforced cellulose acetate butyrate (CAB) biocomposites made with SMC processing had similar physical properties with grass fiber-reinforced HDPE composites, which indicates that natural fiber-reinforced CAB biocomposites have the potential to replace polyolefin-based composites for automotive applications. POLYM. ENG. SCI. 47:969–976, 2007. © 2007 Society of Plastics Engineers.