Quasi‐One Dimensional in‐Plane Conductivity in Filamentary Films of PEDOT:PSS

The mechanism and magnitude of the in‐plane conductivity of poly(3,4‐ethy‐lenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) thin films is determined using temperature dependent conductivity measurements for various PEDOT:PSS weight ratios with and without a high boiling solvent (HBS). Without the HBS the in‐plane conductivity of PEDOT:PSS is lower and for all studied weight ratios well described by the relation $ \sigma = \sigma _0 {\rm exp}[- \left({{{{T_0}}\over{T}}} \right)^{0.5}] $ with T₀ a characteristic temperature. The exponent 0.5 indicates quasi‐one dimensional (quasi‐1D) variable range hopping (VRH). The conductivity prefactor σ₀ varies over three orders of magnitudes and follows a power law σ₀∝c^3.5_PEDOT with c_PEDOT the weight fraction of PEDOT in PEDOT:PSS. The field dependent conductivity is consistent with quasi‐1D VRH. Combined, these observations suggest that conductance takes place via a percolating network of quasi‐1D filaments. Using transmission electron microscopy (TEM) filamentary structures are observed in vitrified dispersions and dried films. For PEDOT:PSS films with HBS, the conductivity also exhibits quasi‐1D VRH behavior when the temperature is less than 200 K. The low characteristic temperature T₀ indicates that HBS‐treated films are close to the critical regime between a metal and an insulator. In this case, the conductivity prefactor scales linearly with c_PEDOT, indicating the conduction is no longer limited by a percolation of filaments. The lack of observable changes in TEM upon processing with the HBS suggests that the changes in conductivity are due to a smaller spread in the conductivities of individual filaments, or a higher probability for neighboring filaments to be connected rather than being caused by major morphological modification of the material.     

Full CMOS continuous time filters for GSM applications

This paper describes full cmoscontinuous time filter design techniques which can meet the specifications commonly set for gsmapplications. First several cmosfilter design techniques are overviewed. The ota-ctechnique is discussed to some more detail. To overcome the main drawback of the lower total harmonic distortion in ota-ctechniques very linear operational transconductance amplifiers (ota)are required. Such an ota,together with the applied linearisation techniques is discussed. To fulfil high accuracy in cut- off frequencies of the filter an active tuning system is necessary. A new on- chip tuning system is presented. The paper concludes with a practical design example for the gsmsystem. Therein the different ota-ctechniques discussed are illustrated.     

Equivalent network representation of boundary conditions involving generalized trial quantities

Virtual adjustable sources are introduced in equivalent network representation of boundary conditions. For this purpose, integral equations are to be solved simple application of analog Kirchoff’s and Ohm’s laws. These adjustable sources represent generalized trial quantities. In order to illustrate this proposed approach, equivalent network representation of lossy planar transmission lines with arbitrary metallization thickness is presented.     

A Complete Separation of Hexane Isomers by a Functionalized Flexible Metal Organic Framework

The separation ability of branched alkane isomers (nHEX, 3MP, 22DMB) of the flexible and functionalized microporous iron(III) dicarboxylate MIL‐53(Fe)‐(CF₃)₂ solid is evaluated through a combination of breakthrough experiments (binary or ternary mixtures), adsorption isotherms, X‐ray diffraction temperature analysis, quasi‐elastic neutron scattering measurements and molecular dynamics simulations. A kinetically controlled molecular sieve separation between the di‐branched isomer of hexane 22DMB from a mixture of paraffins is achieved. The reported total separation between mono‐ and di‐branched alkanes which was neither predicted nor observed so far in any class of porous solids is spectacular and paves the way towards a potential unprecedented upgrading of the RON of gasoline.     

Microwave active resonator band-pass filters in various mmic technologies

In this article, two topologies of L-C parallel active resonators are presented. These circuits are realized in MMIC technology, using three transistors which could be MESFET, hemt or HBT. The survey of these resonators shows the possibility, by controling the values of a resistor and/or a capacitor, on the one hand, to tune the resonance frequency of these circuits, and on the other hand, to cancel out their losses so as to obtain negative conductance. Compact, lossless and narrow-band filters are then implemented using previous active resonators. To date, the use of mesfet technology has reduced the synthesis of such active filters in S-band and at X-band low frequencies. Now, however, hemt and HBT technologies allow the extension of their implementation to the whole X-band. This survey is illustrated by the simulated response of a 10 GHz filter with a 500 MHz 3 dB bandwidth. The mmic technology is a 0.2 μm hemt one. The simulated performances of this filter achieve a mean transmission gain of 0. 5 dB, with a reflection loss higher than 10 dB at 10 GHz,     

Spreading Codes Generator for Wireless CDMA Networks

The prime characteristic of spread spectrum modulated signals is that their bandwidth is greater than the information rate. In this way a redundancy is introduced that allows the severe levels of inteference inherent in the transmission of digital information over radio and satellite links to be overcome. Current spread spectrum applications are primarily in military communications; nevertheless, there is growing interest in this technique for third generation mobile radio networks (UMTS, FPLTS, etc.) with open discussion regarding the practicality of using a multiple access system based on spread spectrum techniques (CDMA). However, in order to support as many users in the same bandwidth as other multiple access techniques such as TDMA or FDMA, it is important how to generate large families of sequences that present low cross-correlation. The aim of this paper is to describe a spreading codes generator that can produce a large number of PN sequences with good properties of auto- and cross-correlation. Moreover, the codes generated shows high unpredictability and good statistical behaviour. This also allows the implementation of some features that are common on military networks such as message privacy (increasingly important in commercial networks) without additional cost. The structure presented shows itself to be advantageous for high speed generation of codes at a low cost, low power consumption (allowing longer life for batteries), small size and simplicity of implementation, essential ingredients for commercial equipment. Another attractive feature is its structural parallelism, useful in VLSI implementations. All of these features render it potentially suitable for the implementation of channel bandwidth sharing systems in future wireless personal communications networks.     

A High Voltage Line Driver for Subscriber Loop Interfaces in a Low Voltage Submicron BiCMOS Technology

This paper presents a 30 V line driver for short loop subscriber line interface circuit applications. The high voltage line drivers was implemented in a low-voltage 0.8 m BiCMOS process using 30 V extended-drain MOS transistors, fully compatible with the low voltage technology. Using a Quasi-Current Mirror architecture for the output stage, the line driver is capable of delivering more than 30 mA current into the lines with an idle current as low as 1 mA, satisfying the short loop requirements. With less than 0.24 mm² area, the circuit can be easily integrated with low-voltage circuitry on a single chip.     

Study of the glucide fraction in ropy wines

Gas chromatography was used to study the polysaccharides present in samples that exhibited significant microbially induced viscosity values. Alterations in the media considered were related to the percentage glucose content and the total polysaccharide content.