Bioinspired pressure actuated adhesive system

We developed a dry synthetic adhesive system inspired by gecko feet adhesion that can switch reversibly from adhesion to non-adhesion with applied pressure as external stimulus. Micropatterned polydimethylsiloxane (PDMS) surfaces with pillars of 30 μm length and 10 μm diameter were fabricated using photolithography and moulding. Adhesion properties were determined with a flat probe as a function of preload. For low and moderate applied compressive preloads, measured adhesion was 7.5 times greater than on flat controls whereas for high applied preloads adhesion dropped to very low values. In situ imaging shows that the increased preload caused the pillars to deform by bending and/or buckling and to lose their adhesive contact. The elasticity of PDMS aids the pillar recovery to the upright position upon removal of preload enabling repeatability of the switch.     

Study of bulk and grain-boundary conductivity of Ln<Subscript>2+x</Subscript>Hf<Subscript>2−x</Subscript>O<Subscript>7−δ</Subscript> (Ln = Sm-Gd; x = 0, 0.096) pyrochlores

The electrical conductivity of new solid electrolytes Eu_2.096Hf_1.904O_6.952 and Gd₂Hf₂O₇ have been compared with those for different pyrochlores including titanates and zirconates Ln_2+xМ_2−xO_7−δ (Ln = Sm-Lu; M = Ti, Zr; x = 0−0.81). Impedance spectroscopy data demonstrate that Eu_2.096Hf_1.904O_6.952 and Gd₂Hf₂O₇ synthesized from mechanically activated oxides have high ionic conductivity, comparable to that of their zirconate analogues. The bulk and grain-boundary components of conductivity in Sm_2.096Hf_1.904O_6.952 (Т_synth = 1600oС), Eu_2.096Hf_1.904O_6.952 and Gd₂Hf₂O₇ (Т_synth = 1670oС) have been determined. The highest bulk conductivity is offered by the disordered pyrochlores prepared at 1600oC and 1670oC: ~1.5 × 10⁻⁴ S/cm for Sm_2.096Hf_1.904O_6.952, 5 × 10⁻³ S/cm for Eu_2.096Hf_1.904O_6.952 and 3 × 10⁻³ S/cm for Gd₂Hf₂O₇ at 780oС, respectively. The conductivity of the fluorite-like phases at the phase boundaries of the Ln_2+xМ_2−xO_7−δ (Ln = Eu, Gd; M = Zr, Hf; x ~ 0.286) solid solutions, as well as that of the high-temperature fluorite-like phases Ln_2+xМ_2−xO_7−δ (Ln = Eu, Gd; M = Zr, Hf; x = 0−0.286), is lower than the conductivity of the disordered pyrochlores Ln_2+xМ_2−xO_7−δ (Ln = Eu, Gd; M = Zr, Hf; x = 0−0.096).     

Electrochemical characteristics of semi conductive silicon anode for lithium polymer batteries

In this paper, the electrochemical characteristics of semi conductive silicon thin films (n-type and p-type silicon) anodes integrated with the solid polymer electrolyte for lithium polymer batteries were investigated. The charge/discharge cycling tests revealed that the phosphorus-doped n-type silicon electrode shows the most stable cyclic performance after the 40^th cycle and still maintains a reversible specific capacity of about 2,500 mAh/g. The enhanced electrochemical performance of the doped silicon anode was attributed to the enhancement of its electrical conductivity, which was further confirmed by impedance spectroscopy and surface analysis by XPS.     

Optimized in-phase and opposed-phase MR imaging for accurate detection of small fat or water fractions: theoretical considerations and experimental application in emulsions

Object  

To optimize strategies and measurement parameters for quantification of small fat and water fractions (<10%) in mixtures of both components by 4-point in-phase and opposed-phase gradient-echo imaging and to compare theoretical results with in-vitro experiments using emulsions.     

The Dynamic Emission Zone in Sandwich Polymer Light‐Emitting Electrochemical Cells

In light‐emitting electrochemical cells (LECs), the position of the emission zone (EZ) is not predefined via a multilayer architecture design, but governed by a complex motion of electrical and ionic charges. As a result of the evolution of doped charge transport layers that enclose a dynamic intrinsic region until steady state is reached, the EZ is often dynamic during turn‐on. For thick sandwich polymer LECs, a continuous change of the emission color provides a direct visual indication of a moving EZ. Results from an optical and electrical analysis indicate that the intrinsic zone is narrow at early times, but starts to widen during operation, notably well before the electrical device optimum is reached. Results from numerical simulations demonstrate that the only precondition for this event to occur is that the mobilities of anions (μ_a) and cations (μ_c) are not equal, and the direction of the EZ shift dictates μ_c > μ_a. Quantitative ion profiles reveal that the displacement of ions stops when the intrinsic zone stabilizes, confirming the relation between ion movement and EZ shift. Finally, simulations indicate that the experimental current peak for constant‐voltage operation is intrinsic and the subsequent decay does not result from degradation, as commonly stated.     

IP QoS across multiple management domains: practical experiences from pan-European experiments

GEANT is the pan-European 10 Gbs network interconnecting European national research and educational networks (NRENs). A Premium IP service based on the DiffServ EF PHB has been specified and implemented for this environment to provide quality of service to selected user groups on a Europe-wide scale. Basic features of Premium IP are described, and results from early experiments in the production networks of GEANT and the NRENs are presented. Next steps are proposed for achieving a fast and wide availability of Premium IP in the European research networks.     

Functionalized Graphene as Extracellular Matrix Mimics: Toward Well‐Defined 2D Nanomaterials for Multivalent Virus Interactions

Polysulfated nanomaterials that mimic the extracellular cell matrix are of great interest for their potential to modulate cellular responses and to bind and neutralize pathogens. However, control over the density of active functional groups on such biomimetics is essential for efficient interactions, and this remains a challenge. In this regard, producing polysulfated graphene derivatives with control over their functionality is an intriguing accomplishment in order to obtain highly effective 2D platforms for pathogen interactions. Here, a facile and efficient method for the controlled attachment of a heparin sulfate mimic on the surface of graphene is reported. Dichlorotriazine groups are conjugated to the surface of graphene by a one‐pot [2+1] nitrene cycloaddition reaction at ambient conditions, providing derivatives with defined functionality. Consecutive step by step conjugation of hyperbranched polyglycerol to the dichlorotriazine groups and eventual conversion to the polyglycerol sulfate result in the graphene based heparin biomimetics. Scanning force microscopy, cryo‐transmission electron microscopy, and in vitro bioassays reveal strong interactions between the functionalized graphene (thoroughly covered by a sulfated polymer) and vesicular stomatitis virus. Infection experiments with highly sulfated versions of graphene drastically promote the infection process, leading to higher viral titers compared to nonsulfated analogues.