On the physics of power,energy and economics of renewable electric energy sources - Part II

Renewable Energy Technologies (RETs) are often recognized as less competitive than traditional electric energy conversion systems. Obstacles with renewable electric energy conversion systems are often referred to the intermittency of the energy sources [1] and the relatively high maintenance cost. However, due to an intensified discourse on climate change and its effects, it has from a societal point of view, become more desirable to adopt and install CO₂ neutral power plants. Even if this has increased the competitiveness of RETs in a political sense, the new goals for RET installations must also be met with economical viability. We propose that the direction of technical development, as well as the chosen technology in new installations, should not primarily be determined by policies, but by the basic physical properties of the energy source and the associated potential for inexpensive energy production. This potential is the basic entity that drives the payback of the investment of a specific RET power plant. With regard to this, we argue that the total electric energy conversion system must be considered if effective power production is to be achieved, with focus on the possible number of full loading hours and the Degree of Utilization [2]. This will increase the cost efficiency and economical competitiveness of RET investments, and could enhance faster diffusion of new innovations and installations without over-optimistic subsidies. This paper elaborates on the overall problem of the economy of renewable electric energy conversion systems by studying the interface between physics, engineering and economy reported for RET power plants in different scientific publications. The core objective is to show the practical use of the Degree of Utilization and how the concept is crucial for the design and economical optimization disregarding subsidies. The results clearly indicate that the future political regulative frameworks should consider the choice of renewable energy source since this strongly affects the economical output from the RET power plants.     

High-throughput data analysis for detecting and identifying differences between samples in GC/MS-based metabolomic analyses

In metabolomics, the objective is to identify differences in metabolite profiles between samples. A widely used tool in metabolomics investigations is gas chromatography-mass spectrometry (GC/MS). More than 400 compounds can be detected in a single analysis, if overlapping GC/MS peaks are deconvoluted. However, the deconvolution process is time-consuming and difficult to automate, and additional processing is needed in order to compare samples. Therefore, there is a need to improve and automate the data processing strategy for data generated in GC/MS-based metabolomics; if not, the processing step will be a major bottleneck for high-throughput analyses. Here we describe a new semiautomated strategy using a hierarchical multivariate curve resolution approach that processes all samples simultaneously. The presented strategy generates (after appropriate treatment, e.g., multivariate analysis) tables of all the detected metabolites that differ in relative concentrations between samples. The processing of 70 samples took similar time to that of the GC/TOFMS analyses of the samples. The strategy has been validated using two different sets of samples: a complex mixture of standard compounds and Arabidopsis samples.     

Trams-a risk factor for pedestrians

In Gothenburg tram injuries were identified to be an important cause of traffic injuries and fatalities (48%) among pedestrians. During the summer middle-aged men, often under the influence of alcohol, were often severely injured and the injury rate was also high during the autumn. A majority (60%) of those fatally injured were under the influence of alcohol. Most injury events happened at or near a tram stop. The most serious injuries arose when the victim landed under a tram. In 1992, a runaway tram caused a major disaster, killing 10 pedestrians and injuring 30. The injury reducing measures the tram company has now started to introduce include safety railings at tram stops, side barriers on the tramcars to prevent people from falling under the tram and lower speeds near tram stops.     

Alkoxide route to La0.5Sr0.5CoO3 epitaxial thin films on SrTiO3

An all alkoxide based sol–gel route was investigated for preparation of epitaxial La_0.5Sr_0.5CoO₃ (LSCO) films on 100 SrTiO₃ (STO) substrates. Films with 20–30 to 80–100 nm thickness were prepared by spin-coating 0.2–0.6 M (metal) solutions on the STO substrates and heat treatment to 800 °C at 2 °C min^− 1, 30 min, in air. The films were epitaxial with a cube-on-cube alignment and the LSCO cell was strained to match the STO substrate of 3.905 Å closely; a and b = 3.894 Å and 3.897 Å for the 20–30 and 80–100 nm films, respectively. The c-axis was compressed to 3.789 Å and 3.782 Å for the 20–30 and 80–100 nm films, respectively, which resulted in an almost unchanged cell volume as compared to polycrystalline film and nano-phase powders prepared in the same way. The SEM study showed mainly very smooth, featureless surfaces, but also some defects. A film prepared in the same way on an -Al₂O₃ substrate was dense and polycrystalline with crystallite sizes in the range 10–50 nm and gave cubic cell dimensions of a_c = 3.825 Å. The conductivity of the ca 30–40 nm thick polycrystalline film was 1.7 mΩcm, while the epitaxial 80–100 nm film had a conductivity of around 1.9 mΩcm.     

Nanoporous aluminum oxide membranes for filtration and biofunctionalization

Nanoporous aluminum oxide membranes with high open porosity are prepared by anodic oxidation. Conventional self-supporting as well as mechanically stabilized nanoporous membranes are produced from aluminum plates and microimprinted aluminum foils, respectively. The mechanically stabilized membranes are characterized by very thin membrane parts stabilized by surrounding thick bridges. The minimal thickness of these thin membranes with open pores on both sides is 1 microm, with a mean pore size of the parallel open pores of 185 nm. With these two kinds of membrane the flow rates for cross filtration can be tuned over a wide range. With the mechanically stabilized membranes, substantially higher flow rates are achieved and experiments that cannot be performed with thicker membranes become possible. The biofunctionalization of the pore walls with archaebacterial tetraether lipids is realized and proved using aminated semiconductor nanocrystals. The lipid layer deposited on the pore walls also changes the filtration properties.     

High‐Sensitivity Real‐Time Analysis of Nanoparticle Toxicity in Green Fluorescent Protein‐Expressing Zebrafish

Gold nanoparticles (AuNP) show great potential for diagnostic and therapeutic application in humans. A great number of studies have tested the cytotoxicity of AuNP using cell culture. There is, however, an urgent need to test AuNP in vertebrate animal models that interrogate biodistribution and complex biological traits like organ development, whole body metabolism, and cognitive function. The sheer number of different compounds precludes the use of small rodent model for initial screening. The extended fish embryo test (FET) is used here to bridge the gap between cell culture and small animal models. A study on the toxicity of ultrasmall AuNP in wild type and transgenic zebrafish is presented. FET faithfully reproduce all important findings of a previous study in HeLa cells and add new important information on teratogenicity and hepatotoxicity that could not be gained from studying cultured cells.