Closed‐Loop Transmit Diversity Techniques for Small Wireless Terminals and Their Performance Assessment in a Flat Fading Channel

Closed‐loop transmit diversity is considered an important technique for improving the link budget in the third generation and future wireless communication standards. This paper proposes several transmit diversity algorithms suitable for small wireless terminals and presents performance assessment in terms of average signal‐to‐noise ratio (SNR) and outage improvement, convergence, and complexity of operations. The algorithms presented herein are verified using data from measured indoor channels with variable antenna spacing and the results explained using measured radiation patterns for a two‐element array. It is shown that for a two‐element array, the best among the proposed techniques provides SNR improvement of about 3 dB in a tightly spaced array (inter‐element spacing of 0.1 wavelength at 2 GHz) typical of small wireless devices. Additionally, these techniques are shown to perform significantly better than a single antenna device in an indoor channel considering realistic values of latency and propagation errors.     

Measurement of Bulk Mechanical Properties and Modeling the Load-Response of Rootzone Sands. Part 1: Round and Angular Monosize and Binary Mixtures

The bulk mechanical properties of two different types of rootzone sands (round and angular) were measured using a cubical triaxial tester. Two monosize sands (d 50 = 0.375 mm and 0.675 mm) and their 50:50 binary mixtures (d 50 = 0.500 mm) were studied. The compression, shear, and failure responses of the above-mentioned six compositions were analyzed, compared, and modeled. Two elastic parameters (bulk and shear moduli) and two elastoplastic parameters (swelling and consolidation indices) of the six sand compositions were also calculated and compared. The angular sand was more compressible than round sand during isotropic compression. In addition, the angular sands tended to have lower initial bulk density and high porosity values. Among the three different size fractions, the 0.375 mm mixture was least compressible for both sand shapes. The failure strength and shear modulus of the angular sand were higher than the round sands. In addition, due to their simplicity, phenomenological models were developed to predict the compression and shear behavior of the sands. The prediction models were validated using subangular and subround sands. Average relative difference values were calculated to determine the effectiveness of the prediction models. The mean average relative difference values for compression profiles, i.e., volumetric stress vs. volumetric strain, were from 16 % to 39 %, except for the initial load-response portion (< 1 % volumetric strain). The predictive models were effective in reproducing the failure responses: at 17.2 kPa confining pressure, the mean of average relative difference was 23 %; at 34.5 kPa , the mean difference was 24 %.     

1, 5-Bis (2-hydroxyacetophenone)thiocarbohydrazone: A novel colorimetric and fluorescent dual-mode chemosensor for the recognition of fluoride

1,5-Bis (2-hydroxyacetophenone)thiocarbohydrazone (H₄L) has been synthesized and characterized by means of spectroscopic and single crystal X-ray diffraction methods. Interactions of the H₄L with a variety of anions were investigated using a combination of UV–visible and fluorescence spectroscopic methods in a biological competing solvent DMSO. The H₄L has a high degree of selectivity for fluoride over other anions. ¹H NMR titration experiments indicate that a deprotonation process is involved in the chemo sensing process.     

TSTL: the template scripting testing language

International Journal on Software Tools for Technology Transfer - A test harness, in automated test generation, defines the set of valid tests for a system, as well as their correctness properties....     

Effect of amphiphilic compatibilizers on the filler dispersion and properties of polyethylene—thermally reduced graphene nanocomposites

Compatibilizers of different chemical structures and specifications were used to enhance the filler exfoliation in nanocomposites of polyethylene and thermally reduced graphene prepared by melt mixing route. The mechanical performance of the compatibilized nanocomposites was observed to be better than PE/G nanocomposites due to enhanced extent of filler exfoliation and distribution. Highest increase of 45% in tensile modulus and 13% in peak stress was observed in the composites. Overall, from the mechanical, rheological, thermal, and calorimetric properties, the compatibilizers with best performance were ethylene acrylic acid (EAA) copolymer and chlorinated polyethylene (CPE25). Furthermore, the extent of filler exfoliation was observed to increase with increasing EAA content thus confirming positive interactions between EAA and thermally reduced graphene, though no specific chemical interactions could be detected. The composite properties were observed to reach maximum around 7.5 wt % EAA content, followed by reduced performance due to extensive matrix plasticization. The observed behaviors were a result of interplay of opposing factors like filler exfoliation due to compatibilizer addition and matrix plasticization due to its lower molecular weight, thus the observed optimum comaptibilizer amount was specific to the compatibilizer. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42484.     

Radiation dose from dissolved radon in potable waters of the Bangalore environment,South India

Potable waters from various locations of the Bangalore environment were investigated for their ²²²Rn concentrations by the emanometry method. About 94 groundwater (borewell) samples were analysed for ²²²Rn concentrations and found to vary in the range 5.3–283.4 Bq L^?1 with a mean value of 87 Bq L^?1. Frequency distribution showed the ²²²Rn concentration in a large number of samples in the range of 0–50 Bq L^?1. From the measured concentrations, the effective doses (lung and stomach) for the population of the region were estimated. The effective dose was found to vary from 42.6 to 2280.2 µSv y^?1 with a mean value 702.5 µSv y^?1. The effect of boiling of water showed a drastic reduction in the ²²²Rn concentration. The results of the present investigation are systematically analysed, compared with the literature values and discussed.     

Noncovalent assembly of carbon nanofiber–layered double hydroxide as a reinforcing hybrid filler in thermoplastic polyurethane–nitrile butadiene rubber blends

A new synthetic route was applied to develop carbon nanofiber (CNF)–layered double hydroxide (LDH) hybrid through a noncovalent assembly using sodium dodecyl sulfate as bridging linker between magnesium–aluminum LDH and CNF and then characterized. Furthermore, this hybrid was used as nanofiller in thermoplastic polyurethane–acrylonitrile butadiene rubber (TN; 1:1 w/w) blend. Mechanical measurements showed that the 0.50 wt % hybrid loaded TN blend exhibited the maximum improvements in the elongation at break, tensile strength, and storage modulus of 1.51 times and 167 and 261% (25 °C), respectively. Differential scanning calorimetric analysis and thermogravimetric analysis showed maximum improvements in the melting temperature (5 °C), crystallization temperature (17 °C), and thermal stability (14 °C) in the 0.50 wt % surfactant modified carbon nanofiber–LDH loaded blend compared to the neat blend. Such enhancement in the properties of the TN nanocomposites could be attributed to the homogeneous dispersion, strong filler–blend interfacial interaction, and synergistic effect. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43470.     

Experimental analysis and development of correlations for gas holdup in high pressure slurry co-current bubble columns

The effect of liquid and gas velocities, solid concentrations, and operating pressure has been studied experimentally in a 15 cm diameter air-water-glass beads bubble column. The superficial gas and liquid velocities varied from 1.0 to 40.00 cm/s and 0 to 16.04 cm/s, respectively, while the solid loading varied from 1 to 9%. The gas holdup in the column was reduced sharply as we switched from batch to co-current mode of operation. At low gas velocity, the effect of liquid velocity was insignificant; while at high gas velocity, increasing liquid velocity decreased the gas holdup. Drift flux approach was applied to quantify the combined effect of liquid and gas velocities over gas holdup. For co-current three phase flows, the gas holdup decreased with increase in solid loading for all pressures. But for batch operations, when solid loading was 5% or more, settling started leading to higher gas holdup. Increasing pressure from atmospheric conditions increased the gas holdup significantly, flattening asymptotically.     

Changes in Pigments and Volatiles of Saffron ( Crocus sativusL) During Processing and Storage

Significant variations were observed in the concentration of pigments (10·0–17·0%, moisture-free basis) and flavour components during different post-harvest processing conditions of saffron (stigmas ex Crocus sativus L). The crocin pigments concentration was highest (15–17%) in the saffron samples dried between 35°C and 50°C either in a solar dryer or in an oven dryer and this also resulted in considerable reduction of normal drying time. Under these conditions the main flavouring component, safranal, was at its peak value of 60% in the oil in almost all the samples except the vacuum oven dried samples which interestingly contained 4-β-hydroxysafranal in major amounts. Studies indicated that 4-β-hydroxysafranal may be an intermediate in the formation of safranal. It was observed that prolonged storage affected the pigments and flavour concentration to a great extent, but proper packaging and storage with 5% moisture in the saffron reduced the deterioration, thereby increasing the shelflife of the product.     

Production of Starch Saccharifying Enzyme (Glucoamylase) in Solid Cultures

A laboratory process was established for the production of glucoamylase (amyloglucosidase) enzyme by Aspergillus niger (RRL isolate), using wheat bran of mixed particle size as main carbon source in solid cultures. The experimental studies were carried out in 500 ml conical flasks and subsequently in tray fermenters in static conditions. Experiments were conducted to monitor the impact of initial moisture content of the substrate as well as the steam cooking of the substrate on different atmospheric pressure on the productivity of the enzyme. An initial moisture level of 50–55% was found optimum for glucoamylase production when fermentation was carried out for 96h. Cooking of substrate at 1056 kg/cm² under steam for 30 min gave most desirable qualities in substrate.