The distribution of grain boundary planes in polycrystals

During the last ten years, techniques have been developed to measure the distribution of grain boundaries in polycrystals as a function of both lattice misorientation and grain boundary plane orientation. This paper presents a brief overview of the techniques used for these measurements and the principle findings of studies implementing these techniques. The most significant findings are that grain boundary plane distributions are anisotropic, that they are scale invariant during normal grain growth, that the most common grain boundary planes are those with low surface energies, that the grain boundary populations are inversely correlated with the grain boundary energy, and that the coincident site lattice number is a poor predictor of the grain boundary energy and population.     

Effect of copper chelates on U.V. stability of butyl rubber and SBR rubber

An investigation of the photo-oxidative degradation and stabilization of IIR and SBR in the temperature range of 258 to 313°K in air with a monochromatic light of 366 nm in the absence and presence of various concentrations of the different copper chelates has been described. The stabilizer performance in IIR and SBR was accessed by carbonyl index and quantum yield measurements. The changes of IIR and SBR during the irradiation with an ultra-violet light (366 nm) have been conducted by viscometrically and actinometric techniques. Irradiations were conducted on the films at 0, 2, 4, 6, 8, 10, 12 and 14 hours and various parameters were obtained.     

Abrasion Resistance of Field-Assisted Ion-Exchanged Glass

The fracture strength of HF-etched samples was measured as a function of field-assisted K-Na ion exchange depth, as well as the severity of abrasion. As expected, the more severe the abrasion, the greater the depth required to make the strength insensitive to abrasion. An abrasion-independent weakening mechanism that increased with exchange depth was also found to be operative.     

Preparation of Protein-Stabilized β-Carotene Nanodispersions by Emulsification–Evaporation Method

This work was initiated to prepare protein-stabilized β-carotene nanodispersions using emulsification–evaporation. A pre-mix of the aqueous phase composed of a protein and hexane containing β-carotene was subjected to high-pressure homogenization using a microfluidizer. Hexane in the resulting emulsion was evaporated under reduced pressures, causing crystallization and precipitation of β-carotene inside the droplets and formation of β-carotene nanoparticles. Sodium caseinate (SC) was the most effective emulsifier among selected proteins in preparing the nanodispersion, with a monomodal β-carotene particle-size distribution and a 17-nm mean particle size. The results were confirmed by transmission-electron microscopy analysis. SC-stabilized nanodispersion also had considerably high ζ-potential (−27 mV at pH 7), suggesting that the nanodispersion was stable against particle aggregation. Increasing the SC concentration decreased the mean particle size and improved the polydispersity of the nanodispersions. Nanodispersions prepared with higher β-carotene concentrations and higher organic-phase ratios resulted in larger β-carotene particles. Although increased microfluidization pressure did not decrease particle size, it did improve the polydispersity of the nanodispersions. Repeating the microfluidization process at 140 MPa caused the nanodispersions to become polydisperse, indicating the loss of emulsifying capacity of SC due to protein denaturation.     

Graft-copolymerization of starch with acrylamide,II. Thermal behaviour of graft copolymers

Thermal behaviour of starch-graft-polyacrylamide (S-g-PAM) copolymers was evaluated. Grafting of polyacrylamide onto starch lowers the initial decomposition temperature. However, the over-all stability as assessed by the shape of thermogravimetric curve and integral procedural decomposition temperature increased with an increase in % graft-on.     

Informational Entropy: a Failure Tolerance and Reliability Surrogate for Water Distribution Networks

Evolutionary algorithms are used widely in optimization studies on water distribution networks. The optimization algorithms use simulation models that analyse the networks under various operating conditions. The solution process typically involves cost minimization along with reliability constraints that ensure reasonably satisfactory performance under abnormal operating conditions also. Flow entropy has been employed previously as a surrogate reliability measure. While a body of work exists for a single operating condition under steady state conditions, the effectiveness of flow entropy for systems with multiple operating conditions has received very little attention. This paper describes a multi-objective genetic algorithm that maximizes the flow entropy under multiple operating conditions for any given network. The new methodology proposed is consistent with the maximum entropy formalism that requires active consideration of all the relevant information. Furthermore, an alternative but equivalent flow entropy model that emphasizes the relative uniformity of the nodal demands is described. The flow entropy of water distribution networks under multiple operating conditions is discussed with reference to the joint entropy of multiple probability spaces, which provides the theoretical foundation for the optimization methodology proposed. Besides the rationale, results are included that show that the most robust or failure-tolerant solutions are achieved by maximizing the sum of the entropies.     

Performance of floating cum tilted-wick type solar still with the effect of water flowing over the glass cover

A simple transient performance of floating cum tilted-wick type solar still has been presented by incorporating the effects of water flowing over a glass cover, heat capacity of tilted-wick water surface and floating-wick water surface. Explicit expressions for flowing water, glass, tilted-wick water surface and floating-wick water surface temperature and efficiency of the system have been derived. Numerical calculations have been carried out for a typical day in the month of March 2004. The relative standard deviations between the numerical and experimental results of different temperature components of the proposed still have been found. The results indicate that the relative standard deviations between theoretical and experimental results are less than 8% (glass cover), 2% (tiltedwick water surface), 1% (floating-wick water surface) and 2% (flowing water at the lower end of the glass cover) an average for the working hours of the day. Moreover, based on the numerical results, the following conclusions have been drawn: (i) glass cover temperature decreases significantly; (ii) the effect of water flowing over the glass cover has a fascinating effect on the production of distillate output during peak sunny hours; (iii) water flow rate of 1.5 m/s is optimum, and beyond it the efficiency decreases. Experimental investigations have been performed at Sri Ramakrishna Mission Vidyalaya College of Arts and Science, Coimbatore, India.     

Use of cascade reduction potential for selective precipitation of Au,Cu, and Pb in hydrochloric acid solution

Optimization of reduction potential for electroseparation was studied for the recovery of gold, copper, and lead from acidic solution. A linear sweep voltammetric method enabled us to determine characteristic reduction potentials for each metal and the kinetics of the metal deposition indicated by current-voltage curves. In order to precipitate the metal species sequentially, reduction potentials were examined for the individual and mixed solutions of Au(III), Cu(II), and Pb(II). The three metals were reasonably well isolated from the mixed solutions such as Cu(II)/ Pb(II) and Au(III)/Cu(II)/Pb(II) in the order of the corresponding reduction potentials, in particular, the mass transfer controlled reduction potentials, obtained from linear sweep voltammetry (LSV) measurement.     

Effect of coupling agents on thermal and electrical properties of mica/epoxy composites

The influence of 3-aminopropyltriethoxysilane, 3-glycidyloxypropyltrimethoxysilane, and neoalkoxytric(dioctyl pyrophosphato)zirconate on thermal expansion behavior, dielectric strength, and arc resistance of mica/epoxy composites has been investigated. The addition of mica up to 30% resulted in the reduction of thermal expansion with respect to neat resin. However, the coefficient of linear thermal expansion of 30% mica treated with aminosilane was the least among the various coupling agent-coated filler/epoxy composites. Mica (30%)/epoxy composites showed the highest dielectric strength values (26 kV/mm), but the highest arc resistance was obtained in zirconate-treated mica (30%)/epoxy composite. © 1995 John Wiley & Sons, Inc.