Effects of pretreatment and various operating parameters on permeate flux and quality during ultrafiltration of apple juice

The central composite design with a quadratic model was used to investigate the effect of temperature (20–40 °C) and transmembrane pressure (TMP) (100–300 kPa) as well as pretreatment with gelatin and bentonite (0:0–300:1500 mg L^?1) on permeate flux and fouling resistance during ultrafiltration of apple juice. The changes in some physicochemical properties were also investigated. Pretreatment of apple juice with gelatin and bentonite and an increase in the temperature and TMP significantly improved the permeate flux. In general, physicochemical properties of apple juice other than polyphenolics were not affected by the applied parameters. Using 150 mg L^?1 of gelatin and 750 mg L^?1 of bentonite for fining significantly reduced the total phenolic content and so did the fouling resistance. Fouling resistance also decreased with increasing temperature, and increasing pressure increased the fouling resistance.     

Standardization problem of author affiliations in citation indexes

Academic effectiveness of universities is measured with the number of publications and citations. However, accessing all the publications of a university reveals a challenge related to the mistakes and standardization problems in citation indexes. The main aim of this study is to seek a solution for the unstandardized addresses and publication loss of universities with regard to this problem. To achieve this, all Turkey-addressed publications published between 1928 and 2009 were analyzed and evaluated deeply. The results show that the main mistakes are based on character or spelling, indexing and translation errors. Mentioned errors effect international visibility of universities negatively, make bibliometric studies based on affiliations unreliable and reveal incorrect university rankings. To inhibit these negative effects, an algorithm was created with finite state technique by using Nooj Transducer. Frequently used 47 different affiliation variations for Hacettepe University apart from “Hacettepe Univ” and “Univ Hacettepe” were determined by the help of finite state grammar graphs. In conclusion, this study presents some reasons of the inconsistencies for university rankings. It is suggested that, mistakes and standardization issues should be considered by librarians, authors, editors, policy makers and managers to be able to solve these problems.     

Defining the suitability of new crushed rock aggregate source areas in the North of Kocaeli Province using GIS

This study evaluated the current crushed rock aggregate resources and defined the suitability of potential crushed rock aggregate resource areas in the north of Kocaeli Province by using the geographical information system (GIS). Evaluation of the current aggregate market showed that almost 80 % of the total annual production (14.35 million tonnes) is supplied by the quarries located in Gebze and 20 % of the total annual production (3.65 million tonnes) is supplied by the quarries located in Hereke. The commercial crushed rock aggregate is totally supplied from the limestone and dolomite type carbonate rocks in the northern Kocaeli region. Defining the suitability of potential crushed rock aggregate resource areas was achieved by using GIS methods. First, an aggregate bedrock potential map was developed by using the geological map of the area and categorized as high, moderate and low bedrock potential areas. The high potential areas, which comprised almost 25 % of the northern Kocaeli region, contain carbonate rocks with varying physical, chemical and engineering properties. Secondly, the suitability of the bedrock potential areas was checked by considering the land-use, distance to the county centres and distance to major roads and highways layers in the weighted overlay function of the GIS. The resulting final map contained not suitable, low suitability and suitable areas for crushed rock aggregate. The suitable areas were grouped into three zones according to their geographic distributions. Further, the most promising crushed rock aggregate areas were defined based on the previous field work and surveys in the suitable areas.     

Solvus Composition Paths in Multicomponent Alloys—Experimental Approach and Correlation with Calphad Calculations for the Example Al–Mg–Si

An experimental approach employing temperature and concentration gradients is presented that is suitable for determining a sequence of solvus concentrations in a single experimental cycle. The Al–Mg–Si system is used as an example. Al solid solutions (“(Al)”) with different compositions and Mg₂Si precipitates were equilibrated in the temperature range between 350 and 550 °C. The equilibrium compositions of (Al) were measured by energy dispersive X‐ray spectroscopy in the transmission electron microscope. The coupled temperature‐concentration values represent a path on the ternary solvus surface. Calphad calculations using different thermodynamic data sets were carried out to relate the experimental results to phase diagram evaluations. The measured solvus path agrees well with solvus data calculated with most recent thermodynamic parameter sets. The experimental approach can be applied to multicomponent alloys irrespective of their number of components with the same experimental effort. The efficiently generated solubility data are suitable to support phase diagram evaluations of multicomponent systems by the Calphad method.     

Uncertainty Analysis of Four-Terminal-Pair Capacitance Characterization up 30 MHz

The Impedance Group Laboratories of National Metrology Institute of Turkey previously developed a new method for the characterization of Agilent 16380A-type four-terminal-pair air dielectric capacitance standards ranged from 1 to 1,000 pF up to 30 MHz. This method is based on obtaining all resonance frequencies of standard capacitors using a vector network analyzer in order to calculate inductive residual parameters of the standards. As a continuation of the study, this paper gives a detailed uncertainty analysis for the method.     

Iridium complexes incorporating coumarin moiety as catalyst photoinitiators: Towards household green LED bulb and halogen lamp irradiation

Household LED bulbs and halogen lamps are used to promote the ring-opening photopolymerization of epoxides in the presence of a new series of iridium(III) complexes (IrCs) exhibiting enhanced visible light absorption properties through the introduction of a coumarin moiety. These latter complexes are used as catalyst photoinitiators in an oxidative cycle in combination with a silane and an iodonium salt. Remarkably, even under the selected very soft irradiations (e.g. light intensity lower than 2 mW/cm²), excellent polymerization profiles are obtained (conversions > 80%). The mechanisms are investigated by ESR and luminescence experiments.     

Dual joints for 3D-structures

The increasing popularity of 3D printing is drawing the interest of the research community to the possibilities and challenges of this manufacturing method. Amongst its many uncertainties, we are concerned here with one of its certainties—that reduction of the material required in 3D printing is critical for efficiency and affordability. In this paper, we propose a solution to the computer graphics problem of, given a volume boundary, automatically defining the mesh of a low density internal structure that is 3D-printable. The proposed solution involves two steps. The first step is to define a cell complex partition for the internal space of a volume defined by its boundaries. The second step, is to apply the Skin4Skeleton algorithm, which uses the cell complex dual to produce a 3D-printable cell-complex mesh with a parametrised thickness.     

Conducting carbon/polymer composites as a catalyst support for proton exchange membrane fuel cells

Carbon/poly(3,4‐ethylene dioxythiophene) (C/PEDOT) composites are synthesized by in situ chemical oxidative polymerization of EDOT monomer on carbon black in order to decrease carbon corrosion that occurred in carbon‐supported catalysts used in proton exchange membrane fuel cell. The effects of different dopants including polystyrene sulfonic acid, p‐toluenesulfonic acid and camphorsulfonic acid with the addition of ethylene glycol or dimethyl sulfoxide on the properties of the composites are investigated. The synthesized composites are characterized by X‐ray diffraction, Fourier transform infrared spectroscopy, thermogravimetric analysis, surface area analysis and scanning electron microscope. Electrical conductivity is determined by using the four‐point probe technique. Electrochemical oxidation characteristics of the synthesized C/PEDOT composites are investigated by cyclic voltammetry by applying 1.2 V for 24 h. The composite prepared at 25 °C with p‐toluenesulfonic acid and ethylene glycol shows the best carbon corrosion resistance. Platinum‐supported catalyst by using this composite was prepared using microwave irradiation technique, and it was seen that the prepared catalyst did not significantly lose its hydrogen oxidation and oxygen reduction reaction activities after electrochemical oxidation. Copyright © 2013 John Wiley & Sons, Ltd.     

Polystyrene Containing Carbinolamine/Azomethine Potentially Useful as Antimicrobial Agent: Synthesis and Biological Evaluation

An investigation of antimicrobial properties of 12 novel modified polymer derived from the condensation reaction of (aminomethyl)polystyrene and four substitute salicylaldehyde (2-hydroxy benzaldehyde, 5-fluoro-2 hydroxy benzaldehyde, 5-fluoro-3-chloro-salicylaldehyde and 5-fluoro-3-methyl-salicylaldehyde) has been carried out and Cr(III) and Ni(II) complexes have been prepared. Modified polymers were characterized by magnetic susceptibility, elemental analyses, and spectral studies. The ¹H NMR and ¹³C NMR spectra analysis of the polymeric carbinolamine/azomethine were determined. In addition, surface morphology and composition were determined by SEM/EDX. Thermo gravimetric analyses of polymers were carried out in nitrogen atmosphere. Antibacterial activities of the polymers attached carbinolamine/azomethine and their complexes were studied by the well-diffusion method against Listeria monocytogenes 4b, Staphylococcus aureus, Escherichia coli, Salmonella typhi H, Brucella abortus, Staphylococcus epidermis sp., Micrococcus luteus, Shigella dysenteria type 10, Bacillus cereus, Pseudomonas putida and antifungal activity against Candida albicans.