Control of the particle microstructure during the synthesis of bulk-polymerized transparent methacrylate-acrylonitrile-butadiene-styrene resin

A series of methacrylate-acrylonitrile-butadiene-styrene (MABS) resins was prepared using bulk polymerization. The polarity of the continuous phase and the compatibility of two phases were changed by adjusting the methyl methacrylate (MMA) content, choosing values that were close to styrene-butadiene rubber solubility value. The possibility of controlling the microstructure of the MABS resin by changing the polarity of the components and the compatibility of two phases was assessed. The dynamic mechanical analysis shows that the compatibility of two phases varies with the MMA content. The morphological analysis shows that increasing MMA contents results in a gradual decrease in the sub-inclusion structure with a network skeleton of rubber particles, and that all the particles become solid rubber when the MMA content reaches 75%. The sub-inclusion structure reappears but does not have a network skeleton when the MMA content is 90%. The impact strength and morphological analysis indicate that the solid rubber particles and the sub-inclusion structure with a network skeleton provide excellent toughness, while the sub-inclusion structure without a network skeleton does not. In contrast, the transmittance of the ABS resin first increased and then decreased with increasing MMA content.     

Room Temperature Ferromagnetism in Co-doped CuAlO2 Nanofibers Fabricated by Electrospinning

One-dimensional, diluted magnetic semiconductor nanofibers have attracted increasing attention for their unique magnetic properties, large specific surface area, and high porosity. These qualities lead to excellent performance in magneto-optical devices, magnetic resonance imaging, ferrofluids and magnetic separation. The purpose of this study is to fabricate P-type one dimensional CuAlO2-based diluted magnetic semiconductor nanofibers. First, we fabricated Cu Al0.95Co0.05O2 nanofibers with an average diameter of 1 μm with the electrospinning method. The annealed nanofibers were thermally treated at a temperature of 1 100 ℃ and then shrunk to a diameter of about 650 nm. We used X-ray diffraction measurements and Raman spectra to confirm that the Cu Al0.95Co0.05O2 nanofibers had a single impurity free delafossite phase. The X-ray photoelectron spectroscopy analysis indicates that Co was present in the +2 oxidation state, resulting in an room temperature ferromagnetism in the Cu Al0.95Co0.05O2 fiber. This contrasts with nonmagnetism in pristine CuAlO2 fiber. The coercivity(Hc) value of 65.26 Oe and approximate saturation magnetization(Ms) of 0.012 emu/g demonstrate good evidence of ferromagnetism at room temperature for Cu Al0.95Co0.05O2 nanofibers.     

Hopping transport in the space-charge region of p-n structures with InGaN/GaN QWs as a source of excess 1/f noise and efficiency droop in LEDs

Semiconductors - It is shown that the emission efficiency and the 1/f noise level in light-emitting diodes with InGaN/GaN quantum wells correlate with how the differential resistance of a diode...     

In situ characterization of LiY(WO4)2 nanotubes for electrochemical energy storage

Here, LiY(WO₄)₂ nanotubes are prepared via a feasible electrospinning technique. This new anode material shows excellent electrochemical properties. The capacity loss of LiY(WO₄)₂ nanotubes is as low as 6.9% after 156 cycles, while bulk LiY(WO₄)₂ presents the capacity loss higher than 55.0%. Even after 600 long-life cycles, the capacity loss of the nanotubes is only 9%. It can be seen that the hollow structure with a rough surface and a porous morphology contributes to the improvement of electrochemical performance. Furthermore, online X-ray diffraction (XRD) method is firstly applied to understand the lithium ions insertion/extraction mechanism of LiY(WO₄)₂ nanotubes. It can be concluded that it is an asymmetrical two-phase reaction. A phase transformation from LiY(WO₄)₂ to Li₃Y(WO₄)₂ can be obviously seen from the in situ XRD during discharge process. While Li₂Y(WO₄)₂ appears as an intermediate phase with a reverse charge reaction. In addition, in situ XRD also demonstrates that LiY(WO₄)₂ nanotubes have surprised electrochemical reversibility. All the above results indicate that LiY(WO₄)₂ nanotubes can be expected to be anode candidate for rechargeable lithium ion batteries (LIBs).     

Steels for Bridge Structures

Metallurgist - We consider domestic and foreign standards for rolled metals used in bridge building. Domestic standards contain elevated requirements to the reliability of rolled metals in terms of...