Electrodeposited CdSe0.5Te0.5: Photoelectrochemical solar cells

CdSe_0.5Te_0.5 thin films have been prepared by electrodeposition. The films were characterized by X-ray diffraction, energy dispersive X-ray fluorescence microanalysis, scanning electron microscopy, optical absorption techniques, Auger electron analysis and electron probe microanalysis. Photoelectrochemical cell performance after electrode annealing and photoetching treatments is reported.     

An Experimental Study to Evaluate the Effect of Ambient Temperature during Manual Lifting and Design of Optimal Task Parameters

In the present study, the effect of lifting task parameters on the heart rate and oxygen uptake of workers during manual lifting tasks in different ambient conditions was evaluated. The experiments conducted in two different temperature conditions showed a significantly higher oxygen uptake and heart rate in colder conditions as compared to warmer conditions. Three other factors, namely, load, lifting frequency, and vertical distance were found to significant affect the responses. Various combinations of significant factors were used to calculate oxygen uptake and heart rate. These were then compared with the safe limits as per the maximum aerobic capacity of workers. Based on these comparisons, the safe combinations were identified that can be used to design lifting tasks in varied ambient conditions. The study further concluded that lifting tasks performed in winter should have different relaxation or fatigue allowances built into the cycle time of the task to compensate for higher exertion. © 2011 Wiley Periodicals, Inc.     

Hardness and Fracture Toughness of SiC-Particle-Reinforced MoSi2 Composites

The indentation technique has been used to evaluate the hardness and fracture toughness of SiC-reinforced MoSi₂ composites made by hot-pressing. It is seen that the toughness increases with increasing indentation crack length (under increasing load) and a probable mechanism responsible for this behavior is described. It is also observed that there is an optimum volume fraction of SiC particles for which the maximum fracture toughness of the composite can be achieved.     

The effect of temperature and moisture on the rheology of black coal-oil suspensions

Rheological properties of black coal-KC220 oil suspensions have been investigated using a Contraves rheometer over a temperature and coal volume fraction range of 18–200°C and 0.247-0.385, respectively. The suspensions behaved as Newtonian fluids. Variation of viscosity with temperature does not follow any regular trend and peak viscosity values occur in the temperature range of 80–140°C for dry coal and 70–130°C for moist coal, depending upon the concentrations of coal in the suspension. Freshly prepared suspensions of moist coal exhibit viscosity peaks at a temperature lower than that of the corresponding suspension with dry coal. However, when aged, the suspensions of moist coal exhibit very small peak viscosity and follow an Arrhenius type behavior. For both dry and moist coal, the maximum volume fraction, ?_m, continues to decrease with an increase in temperature.     

Recycling of ethylene propylene diene monomer (EPDM) waste. III. Processability of EPDM rubber compound containing ground EPDM vulcanizates

The rheological behavior of ethylene propylene diene monomer (EPDM) compounds containing ground EPDM waste (W‐EPDM) of known composition was studied by using a Monsanto processability tester in a temperature range of 90–110°C and a shear rate range of 306.7–1533.24 s^?1. It is found that the shear viscosity decreases slightly with increasing W‐EPDM loading because of wall slip that results from the migration of lubricants from the W‐EPDM. The addition of W‐EPDM to raw EPDM results in a decreased die swell at all temperatures and shear rates. SEM photomicrographs of the EPDM extrudate surface show improved surface smoothness and reduced extrudate distortion when EPDM is blended with W‐EPDM. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 87: 2204–2215, 2003     

Recycling of silicone rubber waste: Effect of ground silicone rubber vulcanizate powder on the properties of silicone rubber

The silicone rubber vulcanizate powder (SVP) obtained from silicone rubber by mechanical grinding exists in a highly aggregated state. The particle size distribution of SVP is broad, ranging from 2 µm to 110 µm with an average particle size of 33 µm. X‐ray Photoelectron Spectroscopy (XPS) and Infrared (IR) Spectroscopy studies show that there is no chemical change on the rubber surface following mechanical grinding of the heat‐aged (200°C/10 days) silicone rubber vulcanizate. Addition of SVP in silicone rubber increases the Mooney viscosity, Mooney scorch time, shear viscosity and activation energy for viscous flow. Measurement of curing characteristics reveals that incorporation of SVP into the virgin silicone rubber causes an increase in minimum torque, but marginal decrease in maximum torque and rate constant of curing. However, the activation energy of curing shows an increasing trend with increasing loading of SVP. Expectedly, incorporation of SVP does not alter the glass‐rubber transition and cold crystallization temperatures of silicone rubber, as observed in the dynamic mechanical spectra. It is further observed that on incorporation of even a high loading of SVP (i.e., 60 phr), the tensile and tear strength of the silicone rubber are decreased by only about 20%, and modulus dropped by 15%, while the hardness, tension set and hysteresis loss undergo marginal changes and compression stress‐relaxation is not significantly changed. Atomic Force Microscopy studies reveal that incorporation of SVP into silicone rubber does not cause significant changes in the surface morphology.     

Microalloyed Steel Bars and Forgings

This paper examines microalloyed steels—steels which develop their properties in the as-received condition without requiring further heat treatment, such as quenching and tempering. Microalloyed steel bars and forgings offer a clear cut potential for cost reduction and energy savings. The metallurgy for producing high strength microalloyed bars and forgings is in place. However, significant improvement in the notch toughness of these materials is necessary, and the metallurgy required to achieve this toughness improvement exists. With application of the necessary metallurgical techniques in rolling mills and forge shops, the utilization of high strength microalloyed steel bars and forgings will increase greatly.     

A piezoelectric model based multi-objective optimization of robot gripper design

The field of robotics is evolving at a very high pace and with its increasing applicability in varied fields, the need to incorporate optimization analysis in robot system design is becoming more prominent. The present work deals with the optimization of the design of a 7-link gripper. As actuators play a crucial role in functioning of the gripper, the actuation system (piezoelectric (PZ), in this case) is also taken into consideration while performing the optimization study. A minimalistic model of PZ actuator, consisting different series and parallel assembly arrangements for both mechanical and electrical parts of the PZ actuators, is proposed. To include the effects of connector spring, the relationship of force with actuator displacement is replaced by the relation between force and the displacement of point of actuation at the physical system. The design optimization problem of the gripper is a non-linear, multi modal optimization problem, which was originally formulated by Osyczka (2002). In the original work, however, the actuator was a ‘constant output-force actuator model’ providing a constant output without describing the internal structure. Thus, the actuator model was not integrated in the optimization study. Four different cases of the PZ modelling have been solved using multi-objective evolutionary algorithm (MOEA). Relationship between force and actuator displacement is obtained using each set of non-dominated solutions. These relationships can provide a better insight to the end user to select the appropriate voltage and gripper design for specific application.