有机硅建筑密封剂及施工管理

本文介绍了有机硅建筑密封剂特点、品种及应用范围，重点介绍其施工程序及管理。     

有关H－Ⅱ运载火箭的动力学课题研究

重点介绍有关Ｈ—Ⅱ运载火箭（以下简称Ｈ—Ⅱ）的一些动力学课题的研究状况。其中，重要的动力学课题有全箭振动、ＰＯＧＯ、防液体晃动、分离动力学试验、动力学环境试验等。针对这些动力学课题，日本有关部门已研究多年，既作了充分的地面试验，又进行了有效的工程应用研究，最终保证了Ｈ—Ⅱ的首次飞行成功。     

EC与~（99m）Tc－GH之间的配体交换反应动力学研究

实验表明，ＥＣ浓度与配体交换反应速度常数无关，体系的ｐＨ值对速度常数和９９ｍＴｃ－ＥＣ的标记率影响较大。测定并计算了不同ｐＨ值的交换反应速度常数。结果表明，为保证用配体交换法制备９９ｍｃ－ＥＣ时９９ｍｃ－ＥＣ的标记率大于９０％，体系的ｐＨ值必须≥８。     

An ET-Based Two-Phase Method for the Calibration and Application of Distributed Hydrological Models

Water Resources Management - Parameter calibration is a core process for the application of distributed hydrological models, which depends strongly on river runoff records. However, the sparse...     

A steel surface defect inspection approach towards smart industrial monitoring

Journal of Intelligent Manufacturing - With the advance in Industry 4.0, smart industrial monitoring has been proposed to timely discover faults and defects in industrial processes. Steel is widely...     

The power reflected in a SAW RAC

Considerations relating to the design of surface-acoustic-wave (SAW) reflective array pulse compressors (RACS), including the effect of array width on power reflected, the transmitted beam profile and the effect of randomized arrays, are discussed. Only a first-order analysis is used. Potential misunderstandings of these issues that could arise from the existing literature are clarified.     

经食道心房调搏的放射性核素心血管造影

本文应用反符合电路剔除调搏脉冲干扰的方法,制成经食道心房调搏心电心音门电路触发装置,用于经食道心房调搏的核素心血管造影。参考Tzivoni标准,当逐级增加调搏心率至140次/min或亚极量心率后发现:冠心病人有调搏后EF降低;急性心肌梗塞病人EF减低更为明显,并呈室壁反向运动。因此,心房调搏核素心血管造影有助于冠心病,特别是心肌梗塞的诊断。     

CHARAC TERIZATION OF TiAl POWDER PRODUCED BY MECHANICAL ALLOYING

The microstructure,alloying reaction and sintering behavior of the powder produced by Mechanical Al-loying(MA)for 8 h from 64 wt.-% Ti powder and 36 wt.-% Al powder were studied by scanning electronmicroscopy,optical microscopy,X-ray diffractometry,differential scanning calorimetry(DSC)and dilatometry.The mechanically alloyed powder partictes are Ti-Al composite particles.Thus,titanium aluminides can formeasily in the powder through diffusion during heat treatment.It is shown that the sintering behavior of this pow-der,different from the behaviors of TiAl alloy powder and mixed powder of 64 wt.-% Ti powder and 36 wt.-%Al powder,changes from expansion at temperatures below 1000℃ to shrinkage at temperatures above 1000℃.Homogeneously alloyed TiAl material with a density over 96% of the theoretical density can be produced fromthe mechanically alloyed powder by compaction-sintering.     

Mold-filling characteristics of AZ91 magnesium alloy in the low-pressure expendable pattern casting process

The magnesium (Mg) alloy low-pressure expendable pattern casting (EPC) process is a newly developed casting technique combining the advantages of both EPC and low-pressure casting. In this article, metal filling and the effect of the flow quantity of inert gas on the filling rate in the low-pressure EPC process are investigated. The results showed that the molten Mg alloy filled the mold cavity with a convex front laminar flow and the metal-filling rate increased significantly with increasing flow quantity when flow quantity was below a critical value. However, once the flow quantity exceeded a critical value, the filling rate increased slightly. The influence of the flow quantity of inert gas on melt-filling rate reveals that the mold fill is controlled by flow quantity for a lower filling rate, and, subsequently, controlled by the evaporation of polystyrene and the evaporation products for higher metal velocity. Meanwhile, the experimental results showed that the melt-filling rate significantly affected the flow profile, and the filling procedure for the Mg alloy in the low-pressure EPC process. A slower melt-filling rate could lead to misrun defects, whereas a higher filling rate results in folds, blisters, and porosity. The optimized filling rate with Mg alloy casting is 140 to 170 mm/s in low-pressure EPC.     

活性酯硬化水玻璃砂的研究

用焙烧活性砂混制而成的活性酯硬化水玻璃砂与普通酯硬化水玻璃砂相比，强度成倍提高，从而减少水玻璃的加入量，改善水玻璃砂的溃散性。实验证明：原砂的表面活性直接影响在水玻璃砂中水玻璃的加入量，是改善水玻璃砂溃散性的关键之一。焙烧活性砂的水玻璃加入量只要１．５％～２．０％，即能满足实际生产的强度要求。