Semivolatile organic compounds in window films from lower Manhattan after the September 11th World Trade Center attacks

The September 11th World Trade Center (WTC) terrorist attacks resulted in the large-scale release of contaminants that were deposited on the environment of New York City (NYC). Six weeks after the attacks, samples of an organic film on window surfaces were collected and analyzed for polybrominated diphenyl ethers (PBDE), polychlorinated biphenyls (PCB), polychlorinated naphthalenes (PCN), polycyclic aromatic hydrocarbons (PAH), and organochlorine pesticides (OCPs). Concentrations dropped by an order of magnitude within 1 km of the WTC and reached background concentrations by 3.5 km. Concentrations within 1 km of the WTC averaged 3280 ng/m2 for sigmaPBDE, 900 ng/m2 for sigmaPCB, 33 ng/m2 for sigmaPCN, and 77100 ng/m2 for sigmaPAH. Congener profiles of the sites nearest the WTC suggested a combination of combustion and evaporative sources of all compounds, whereas the background sites exhibited profiles consistent with evaporative sources. PBDE profiles showed enrichment in lower molecular weight congeners near the WTC, suggesting that these congeners were formed as a result of the combustion conditions. Homologue fractions of PCN combustion markers were approximately 2-9 times greater at near WTC sites compared to background NYC. Gas-phase air concentrations were back-calculated from measured film concentrations using the film-air partition coefficient (KFA), and calculated air concentrations followed spatial trends observed in films.     

A comprehensive design and performance evaluation study of counter flow wet cooling towers

Fouling of cooling tower fills is one of the most important factors affecting its thermal performance, which reduces cooling tower effectiveness and capability with time. In this paper, the fouling model presented in an earlier paper using the experimental data on fill fouling, is used to investigate the risk based thermal performance of the cooling tower. It is demonstrated that effectiveness of the cooling tower degrades significantly with time indicating that for a low risk level (p=0.01), there is about 6.0% decrease in effectiveness for the given fouling model. The sensitivity analysis of the cooling tower is investigated for both rating and design calculation for different values of mass flow rate ratios. The effect of atmospheric pressure on the thermal performance of the cooling tower is also demonstrated.     

A survey on resource allocation in high performance distributed computing systems

An efficient resource allocation is a fundamental requirement in high performance computing (HPC) systems. Many projects are dedicated to large-scale distributed computing systems that have designed and developed resource allocation mechanisms with a variety of architectures and services. In our study, through analysis, a comprehensive survey for describing resource allocation in various HPCs is reported. The aim of the work is to aggregate under a joint framework, the existing solutions for HPC to provide a thorough analysis and characteristics of the resource management and allocation strategies. Resource allocation mechanisms and strategies play a vital role towards the performance improvement of all the HPCs classifications. Therefore, a comprehensive discussion of widely used resource allocation strategies deployed in HPC environment is required, which is one of the motivations of this survey. Moreover, we have classified the HPC systems into three broad categories, namely: (a) cluster, (b) grid, and (c) cloud systems and define the characteristics of each class by extracting sets of common attributes. All of the aforementioned systems are cataloged into pure software and hybrid/hardware solutions. The system classification is used to identify approaches followed by the implementation of existing resource allocation strategies that are widely presented in the literature.     

The peaking effect in the internal friction of copper single crystals

Journal of Materials Science Letters -     

Review of liquid metal corrosion issues for potential containment materials for liquid lead and lead–bismuth eutectic spallation targets as a neutron source

Lead (Pb) and lead–bismuth eutectic (44Pb–56Bi) have been the two primary candidate liquid metal target materials for the production of spallation neutrons. Selection of a container material for the liquid metal target will greatly affect the lifetime and safety of the target subsystem. For the liquid lead target, niobium–1 wt% zirconium (Nb–1Zr) is a candidate containment material for liquid lead, but its poor oxidation resistance has been a major concern. In this paper, the oxidation rate of Nb–1Zr was studied based on the calculations of thickness loss resulting from oxidation. According to these calculations, it appeared that uncoated Nb–1Zr may be used for a 1-year operation at 900°C at P_O2=1×10^–6 Torr, but the same material may not be used in argon with 5-ppm oxygen. Coating technologies to reduce the oxidation of Nb–1Zr are reviewed, as are other candidate refractory metals such as molybdenum, tantalum, and tungsten. For the liquid lead–bismuth eutectic target, three candidate containment materials are suggested, based on a literature survey of the materials’ compatibility and proton irradiation tests: Croloy 2-1/4, modified 9Cr–1Mo, and 12Cr–1Mo (HT-9) steel. These materials seem to be used only if the lead–bismuth is thoroughly deoxidized and treated with zirconium and magnesium.     

Kinetics of Thermal, Passive Oxidation of Nicalon Fibers

The oxidation of Nicalon fibers is a concern, because of its potential as a reinforcement of high-temperature composites, whose service conditions involve high-temperature, oxidizing environments. Two limiting types of oxidation mechanisms are often used to describe the kinetics: chemical-reaction-controlled oxidation, at small oxide thicknesses, and diffusion-controlled oxidation, at large oxide thicknesses. Neither mechanism can satisfactorily describe the intermediate region where the oxidation kinetics are controlled jointly by both the chemical reaction rate at the interface and the diffusion of oxygen through the oxide layer. To describe the entire oxidation process with a general relationship, one must consider all stages of the oxidation process, namely (i) adsorption of oxygen at the outer surface of the oxide, (ii) diffusion of oxygen from the outer surface toward the interface where oxidation occurs, and (iii) reaction at the interface to form a new layer of oxide. Previously, a very useful general relationship was derived for the oxidation kinetics for a flat plate, which could account for all three stages of oxidation. However, that equation is inadequate to describe the oxidation of cylindrical fibers, because the effective area for oxygen diffusion changes along the diffusion path and the oxidation interfacial area decreases as the oxide thickness increases for cylindrical fibers. In this paper, we have derived a general kinetic relationship for the oxidation of cylindrical fibers, which can account for all stages of oxidation. Comparison of the theory with experimental data of Nicalon fibers shows good agreement.     

Morphological and palynological assessment of taxonomically problematic genus Paspalum based on light and scanning electron microscopy

Present research work was carried out to clarify the variations among species of genus Paspalum morphologically and palynologically as this genus is taxonomically difficult due to having multiple similar morphologically overlapping characters which make it difficult to identify. Henceforth present research work was carried out to delimit taxa within the same genus by morphological and palynological tools through light microscopy (LM) and scanning electron microscopy (SEM). Both these tools are considered as the most useful taxonomic characters for taxonomically problematic genera. The results showed a lot of variations among morphological characters. In Paspalum dilatatum, the upper glume was ovate whereas in the other two species, the upper glume was elliptic. The upper glume apex found in P. dilatatum and Paspalum scrobiculatum was obtuse whereas in Paspalum distichum, upper glume apex was acute. Glume nerves showed variation in all three species. Paspalum distichum was 3 nerved, P. scrobiculatum was 5–7 nerved, and P. dilatatum was 5–9 nerved. All three species showed variation in lemma nerves. Paspalum scrobiculatum had 3 nerved lemma whereas in P. distichum 3–5 nerved and P. dilatatum 5–9 nerved lemma were present. In polar and equatorial view, pollen grains ranged from 25 (20–30) to 37.5 (30–45) μm. Paspalum distichum appeared to be the smallest in size whereas P. dilatatum was the largest. Exine thickness ranged from 0.75 (0.5–1) to 1.35 (1.2–1.5) μm. The higher value of pollen fertility was found in P. scrobiculatum as 87.69% and the lowest value was in P. distichum as 78.08%. Morphological keys were also given for correct identification.