Investigation of Mechanical and Electrical Characteristics for Cracked Conductive Particle in Anisotropic Conductive Adhesive (ACA) Assembly

In an anisotropic conductive adhesive (ACA) assembly, the electrical conduction is usually achieved with the conductive particles between the bumps of integrated circuit (IC) and corresponding conductive tracks on the glass substrate. Fully understanding of the mechanical and electrical characteristics of ACA particles can help to optimize the assembly process and improve the reliability of ACA interconnection. Most conductive particles used in the ACA assembly are with cracks in the metal coating of the particles after the ACA bonding. This paper introduced the fracture analysis by applying the cohesive elements in the numerical model of the nickel-coated polymer particle and further simulating the cracks initiation and propagation in the nickel coating during the ACA bonding. The simulation results showed that the stress distribution on the nickel-coated particle with cracks was significantly different from that on the nickel-coated particle without crack, indicating that the stress analysis by taking the crack into consideration is very important for the reliability assessment of the ACA interconnection. The stress analysis of cohesive elements indicated that the cracks initiated at the central area of the nickel coating and propagated to the polar area. Furthermore, by the introduction of a new parameter of the virtual resistance, a mathematical model was established to describe the electrical characteristics of the nickel-coated particle with cracks. The particle resistance of the nickel-coated particle with cracks was found to be much higher than that of the particle without crack in the optimized bonding pressure range, indicating that it is necessary to take the crack into consideration for the particle conduction analysis as well. Therefore, the fracture analysis on the conductive particle by taking the crack into consideration could accurately evaluate the reliability of ACA interconnection and avoid serious reliability issues.     

镁钴铝类水滑石催化合成安息香甲醚

采用共沉淀法制备了镁钴铝类水滑石化合物(MgCoAl-HTLcs),并用 X 射线衍射、扫描电子显微镜、NH_3程序升温脱附等方法对 MgCoAl-HTLcs 进行了表征,并以 MgCoAl-HTLcs 为催化剂催化苯甲醛与甲醇反应合成安息香甲醚,研究了n(Mg):n(Co):n(Al)、催化剂用量、原料配比、反应温度、反应时间对合成反应的影响。表征结果显示,MgCoAl-HTLcs 的晶相完整,表面主要为弱酸、弱碱性。催化合成安息香甲醚的适宜条件为:MgCoAl-HTLcs 催化剂用量0.10 g(约为原料总质量的0.23%),n(Mg):n(Co):n(Al)=0.4:1.6:1.0,V(苯甲醛):V(甲醇)=3:50,反应温度50℃,反应时间150 min。在此条件下,苯甲醛的平衡转化率达77.49%,安息香甲醚选择性接近100%。为洁净合成安息香甲醚开辟了一条新的途径。     

Φ4.0m×60m回转窑辐射热的应用

水泥厂回转窑简体内砌筑了耐火砖隔热,但仍有部分热通过简体以辐射的形式散失到大气中,吸收利用这部分辐射热也是一项节能减排的举措.     

实施六大工程打造民生水利

我省针对十年九旱、水资源短缺、生态与环境脆弱的特点，确定了今冬明春农田水利基本建设的目标任务，明确以实施兴水战略为主线，以改善民生为目标，以创新机制为保障，全面掀起冬春农田水利基本建设新高潮。     

宣钢1260 m3高炉扩容大修改造设计

宣钢l260m^3高炉大修改造时将炉容扩大到l350m^3，对高炉本体系统设备及冷却系统、自动控制及检测系统进行了全面的改造更新，在炉腹、炉腰及炉身下部高热负荷区域采用铜冷却壁，取消炉身中上部铸铁冷却壁凸台，并采用薄内衬等先进、适用、可靠、成熟的技术。     

Ф16mm、Ф18mm钼棒的研制

采用等静压制法，压制钼圆棒坯，经中频高温烧结，制得尺寸适合、用户满意的钼电极棒。     

Powder Deposition in Three Parallel-Oriented Dies of Different Shapes

Uniformity of bulk density distribution during the die filling process is required to minimize quality problems, such as distortion and cracking, for powder compacts. Understanding the die filling process is necessary in ensuring a uniform powder deposition. The second-generation pressure deposition tester (PDT-II) was used to investigate the deposition process and final pressure distribution of powder filling in toroidal, cylindrical, and E-shaped dies. All tests were conducted using a spray-dried free-flowing granular powder. The results indicated that for toroidal dies: (1) the area around 0° orientation (the leeward end) had the highest pressure values (1186.7 to 2498.0 Pa), with the average pressure values of the remaining area 353.7-648.0 Pa; (2) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; (3) the highest feed shoe speed (500 mm/s) led to the most nonuniform pressure distribution among the three speeds; (4) higher feed shoe speed did not always result in higher final pressure values; and (5) the right die tended to have higher final pressure values (215.0 to 2498.0 Pa) than the center die (95.4 to 2052.5 Pa). For E-shaped dies: (1) the final pressure values of the middle leg (308.9 to 760.7 Pa) were higher than those of the left and the right legs (148.9 to 530.3 Pa); (2) the area along the backside had the highest final pressure value (1054.6 to 1303.8 Pa); (3) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; and (4) neither the center die nor the right die always had higher pressure values than the other one at all locations. Comparison between cylindrical and toroidal dies indicated that: (1) neither of the two die shapes (cylinder and toroid) led to consistently higher or lower final pressure values at all locations and (2) for all three feed shoe speeds, the toroidal die had higher average final pressure values in the 0° orientation.     

住宅建筑结构中隔震技术的应用和经济评价

对当前隔震系统做了简单介绍 ,介绍了基础隔震的技术和施工方法等。讨论在住宅结构中推广隔震技术的方法 ,对各种类型的住宅结构做经济评价 ,讨论推广的可能性和难点。     

化学束外延

本文介绍了化学束外延(CBE)的发明和发展,论述了CBE的原理和设备。文中还介绍了最近提出的一种生长机理。     

A high-current and high-temperature 6H-SiC thyristor

A 6H-SiC thyristor has been fabricated and characterized. A forward breakover voltage close to 100 V and a pulse switched current density of 5200 A/cm² have been demonstrated. The thyristor is shown to operate under pulse gate triggering for turn-on and turn-off, with a rise time of 43 ns and a fall time of less than 100 ns. The forward breakover voltage is found to decrease by only 4% when the operating temperature is increased from room temperature to 300°C. It is found that anode ohmic contact resistance dominates the device forward drop at high current densities