Erosion-corrosion behavior of SiC particle-reinforced Al-Si alloy in NaOH slurry

The erosion-corrsosion behavior of SiC particle-reinforced Al-Si alloy has been studied in NaOH slurry simulating the mining atmosphere. The study was performed at two different sand concentrations, namely, 20 and 30 wt pct, and at a speed of 900 rpm. It is depicted that the wear rates decreased with increasing sand content, indicating that corrosion is the dominating mode of material removal. Further composite exhibited lower wear resistance than the laloys irrespective of the sand concentration. Scanning electron microscope (SEM) observations indicated the dissolution of dendrites of Al due to severe corrosion, leaving behind the network of Si. This ultimately results in the falling of Si particles from the matrix, leaving behind voids. This also results in the formation of voids around the SiC particles and leads to pullout of SiC particles from the matrix during the wear process.     

Shear Stress in Smooth Rectangular Open-Channel Flows

The average bed and sidewall shear stresses in smooth rectangular open-channel flows are determined after solving the continuity and momentum equations. The analysis shows that the shear stresses are function of three components: (1) gravitational; (2) secondary flows; and (3) interfacial shear stress. An analytical solution in terms of series expansion is obtained for the case of constant eddy viscosity without secondary currents. In comparison with laboratory measurements, it slightly overestimates the average bed shear stress measurements but underestimates the average sidewall shear stress by 17% when the width–depth ratio becomes large. A second approximation is formulated after introducing two empirical correction factors. The second approximation agrees very well (R2>0.99 and average relative error less than 6%) with experimental measurements over a wide range of width–depth ratios.     

超临界水的辐化反应研究

It is known that water exists in supercritical state above 374C and 22.1MPa, where gas phase and liquid phase are merged into a single phase. In the supercritical state, the density is controllable by changing the pressure. The properties such as the ionic product, solubilities of salts, gas and organic compounds, and dielectric constant of supercritical water are very different from those of water at room temperature.Recently much attention has been paid to supercritical water because many possible applications such as synthesis of functional materials, waste oxidation, and biomass conversion have been proposed by using above peculiar properties of the supercritical water. Thus, much intensive work is in progress all over the world. In addition, a new concept of nuclear reactor using the supercritical water as a coolant has been proposed, which has been chosen by DOE, USA as one of the forth generation nuclear reactors.Therefore, radiation chemistry study of the supercritical water seems inevitably important, yet little work has been done so far. We started radiation chemistry study of supercritieal water by pulse radiolysis and γ radiolysis five years ago. We have observed hydrated electrons as a first target. We also measured inorganic radicals, metal ions, organic radicals in high temperature and supercritical water by a pulse radiolysis technique. It was found that absorption spectra of the transient species are dependent on temperature. Some transients show red-shift, and some bands are blue-shifted, with increasing temperatures. A G-value evaluation of water decomposition products was also done by using methyl viologen as a scavenger and it was revealed that the values are significantly dependent not only on temperature but also on density in supercritical water. An extended study on the behavior of solvated eleclions in different alcohols at high temperatures and super critical state is also in progress.     

Evaluation of a Computer-Assisted, 2-D Virtual Reality System for Training People With Intellectual Disabilities on How to Shop.

Objective: To evaluate the effectiveness of a 2-D virtual reality (VR) program for training people with intellectual disabilities to shop. Study Design: Pretest and posttest quasi-experimental design. Participants: Sixteen persons with intellectual disabilities (age 17-23 years; IQ = 40-54). Intervention: A VR program or a conventional program training them in supermarket-shopping skills. Main Outcome Measure: Checklist for supermarket-shopping skills. Results: Participants in both training groups showed significant improvement. There was no significant difference in effectiveness between the two methods. Conclusions: The VR program appears effective in training people with intellectual disabilities in an important community living skill. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Ion-velocity dependence of high-density electronic excitation effects in oxide superconductors

Thin films of EuBa₂Cu₃O_y oxide superconductor have been irradiated with high energy heavy ions (80 MeV I, 125 MeV Br, 1.1 GeV Mo and 3.5 GeV Xe) having same electronic stopping power, S_e, in order to investigate the ion-velocity dependence of the electronic excitation effects under the constant electronic energy deposition. Although S_e is constant, a strong reduction in the irradiation effect on lattice parameter with increasing ion-velocity is observed in the low ion-velocity region around E  1 MeV/nucleon, while the ion-velocity dependence is hardly observed in the high ion-velocity region of E > 10 MeV/nucleon. If the observed velocity-dependence is assumed to be due to the change in the fraction of S_e contributing to defect creation, the fraction in the low velocity region (E  0.6 MeV/nucleon) is estimated to be about two times larger than that in the high velocity region (E > 10 MeV/nucleon).     

Study on Pb-Bi natural circulation phenomena

For the development of 45w%Pb-55w%Bi cooled direct contact boiling water small fast reactor (PBWFR), experimental study on Pb-Bi-water direct contact boiling two-phase flow has been performed using Pb-Bi-water direct contact boiling two-phase flow loop. For stable start-up of the boiling flow operation, Pb-Bi single-phase natural circulation must be realized in a Pb-Bi flow system of the loop before water injection into Pb-Bi. The Pb-Bi flow system consists of a four-heater-pin bundle, a chimney, an upper plenum, a level meter tank, a cooler, and an electromagnetic flow meter. A stable Pb-Bi single-phase natural circulation was realized in the range of flow rate from 1.5 l/min to 4.8 l/min by heating Pb-Bi in the heater-pin bundle with a power up to 7.7 kW. The inlet and outlet temperatures of the heater bundle were in the ranges from 243°C to 278°C, and from 251°C to 278°C, respectively. The natural circulation flow was simulated analytically using one-dimensional flow model including frictional, form and drag forces. Total hydraulic head through the loop were calculated from Pb-Bi densities at measured Pb-Bi temperatures in the loop. It was found that the calculated flow rate agreed well with the measured ones, which indicated the validity of the analytical models.     

A refined beam theory based on the refined plate theory

Summary Based on the refined plate theory, a refined theory of rectangular beams is derived by using the Papkovich-Neuber solution and Lur’e method without ad hoc assumptions. It is shown that the displacements and stresses of the beam can be represented by the angle of rotation and the deflection of the neutral surface. The solutions based on the new theory are the same as the exact solutions of elasticity theory. In three examples it is shown that the new theory provides as good or better results than Levinson’s beam theory when compared to those obtained from the linear theory of elasticity.     

An atomic force microscope study of surface roughness of thin silicon films deposited on SiO/sub 2/

Atomic force microscope analysis, with a resolution of /spl lsim/1.1 nm, shows that peak-to-peak surface roughness (/spl Delta/h/sub p-p/) of amorphous silicon films thinner than /spl ap/50 nm on silicon dioxide can be controlled to better than 5 nm. Low-pressure, chemically-vapor-deposited silicon films on silicon dioxide initially show an approximately linear increase in the surface roughness due to growing nuclei as the deposition progresses, followed by a decrease in the surface roughness as growth nuclei coalesce. A simple model based on random nucleation and nuclei growth displays similar trends. Films deposited on rougher substrates show more surface roughness. Surface treatment during the predeposition cleaning process does not significantly affect /spl Delta/h/sub p-p/. As a means of producing smooth surfaces, films thinner than about 20 nm are first deposited more thickly than needed, and then etched back to the desired dimension; the use of a binary HNO/sub 3/ and HF etching process improves roughness control. Boron-ion implanted and subsequently crystallized 45-nm-thick Si films show significant smoothing with /spl Delta/h/sub p-p//spl ap/2.2 nm. Thin amorphous silicon films deposited by source evaporation are attractive because they can be deposited at room temperature, and have smoother surfaces (/spl Delta/h/sub p-p//spl ap/2.5 nm) than comparable films produced by chemical vapor deposition.