Effect of Microstructure on the Accelerated Creep of 20CrMoV12‐1 and P 91 Steels

In the initial part the change of microstructure for steel X20 CrMoV 121 is discussed in terms of the distribution of carbide precipitates and its effects on accelerated creep resistance and hardness are presented. In the following, experimental results of microstructure and accelerated creep resistance are presented for the steels X20CrMoV 121 and P91 annealed for up to 8760 hours at 650°C and 750°C before the testing. A similar evolution of the distribution of carbide particles of a size above 102 nm is found for both steels, while the accelerated creep resistance is diminished much stronger for the steel X20CrMoV 121. This difference is due to a greater stability of NbC than that of VC precipitates, both related to the evolution of the chemical composition of complex chromium, molybdenum and iron carbide particles.     

Josephson junction with an amorphous silicon barrier

A Josephson junction Nb/Si/Nb with a 10 nm thick amorphous silicon barrier is studied. The upper electrode contains a 2 nm thick sublayer of amorphous phase adjacent to the barrier, as revealed by cross-sectional TEM. Thus, the junction can be considered as a S-I-N-S system with the N layer represented by amorphous niobium. Peculiarities in the I–V and Δ(T) dependencies are observed and explained as a consequence of a proximity effect present in the upper electrode.     

Computer program for the construction of the level scheme on the basis of energy balance of gamma transitions

A computerised method is presented for the construction of the level scheme on the basis of measured energies of the gamma transitions without any previous knowledge of the observed isotope. The method and the steps of the algorithm are discussed. The calculated results are compared with the published schemes for the given isotopes.     

Correlation between magnetic hysteresis and magnetic relaxation in YBaCuO single crystals

The dependence of the magnetic momentm obtained from the hysteresis loops on the speed of the magnetic field sweep =dH _ext/dt is explained on the basis of Anderson's interpretation of the magnetic flux creep. In addition, a phenomenological model is suggested which predicts a linear dependence ofm on ln with the slope m/ ln , numerically equal to the relaxation rate m/ ln(t) from the usual magnetic relaxation. Such linear relations betweenm and ln were observed experimentally in single crystals of YBaCuO. Preliminary experiments on the complementary time dependent relaxation ofm after a simulated step change ofH _ext gave mostly relaxation rates close to the predicted values. The model here presented also enables one to compare the critical state in the superconductor at a field sweep rate with the critical state at some timet _eff after a step change ofH _ext. The values of analyzed in our experiments actually correspond to the critical state at timest _eff between0.04 and4 sec after an imaginary large step change ofH _ext.     

A study of Nd2Fe14B and a neodymium-rich phase in sintered NdFeB magnets

The microstructure and properties of NdFeB sintered permanent magnets were analysed by different methods. Samples analysed were sintered and thermally treated. The hard magnetic Nd₂Fe₁₄B phase and amorphous neodymium-rich phase were observed by TEM. The neodymium-rich phase contained iron and boron, in elemental and in B₂O₃ form, which is known as a glass former. At the sintering temperature, Nd₂Fe₁₄B and the neodymium-rich phase are supersaturated with iron, which should be dissolved at the annealing temperature to react with neodymium and boron and form additional Nd₂Fe₁₄B phase. Iron precipitates of size up to 2 nm were detected in the Nd₂Fe₁₄B phase. These superparamagnetic precipitates of -Fe could affect the hard magnetic properties of NdFeB magnets.     

A case of using the Semantic Interoperability Framework for custom orthopedic implants manufacturing

The efficiency and effectiveness of the daily practice in orthopedic surgery depend on the availability, interoperability and unique access to a wide set of information, related to the patient’s medical record and diagnosis, domain knowledge and available resources and staff. The most important of the tangible resources, needed for the therapeutic or preventive actions are orthopedic implants. In some cases, the implants may be highly complex and customized products, which need to be manufactured (assembled) on basis of the above information in a shortest possible timeframe. In this paper, the case of the custom orthopedic implants manufacturing is described from the perspective of the collaborative enterprising, with special consideration of the interoperability issues of the involved enterprise collaboration. It is shown how the previously developed Semantic Interoperability Framework can be used to improve the efficiency of the manufacturing and other relevant processes.     

Carcass traits and meat quality of male lambs fed monensin or lasalocid

Male lambs, crossbred Merino × Ille de France, were fed a diet supplemented with 31 mg monensin or 32 mg lasalocid per kg of feed dry matter from an initial body weight of 23·6–23·9 kg to the slaughter weight of approximately 40 kg.

Carcass traits and meat quality were evaluated after slaughter; the values obtained were compared with those of the control group fed the same diet without the ionophore supplement.

There were few significant differences among the individual groups in carcass value, sensoric and technological properties of meat and of its composition. However, the lasalocid-fed group seemed to be somewhat better in muscling and in the composition of meat.