Electrochemical synthesis and characterization of chloride doped polyaniline

Chloride doped polyaniline conducting polymer films have been prepared in a protic acid medium (HCl) by potentiodynamic method in an electrochemical cell and studied by cyclic voltammetry and FTIR techniques. The FTIR spectra confirmed Cl^- ion doping in the polymers. The polymerization rate was found to increase with increasing concentration of aniline monomer. But the films obtained at high monomer concentration were rough having a nonuniform flaky polyaniline distribution. Results showed that the polymerization rate did not increase beyond a critical HCl concentration. Cyclic voltammetry suggested that, the oxidation-reduction current increased with an increase in scan rate and that the undoped polyaniline films were not hygroscopic whereas chloride doped polyaniline films were found to be highly hygroscopic.     

Thermomechanical finite-element model of shell behavior in continuous casting of steel

A coupled finite-element model, CON2D, has been developed to simulate temperature, stress, and shape development during the continuous casting of steel, both in and below the mold. The model simulates a transverse section of the strand in generalized plane strain as it moves down at the casting speed. It includes the effects of heat conduction, solidification, nonuniform superheat dissipation due to turbulent fluid flow, mutual dependence of the heat transfer and shrinkage on the size of the interfacial gap, the taper of the mold wall, and the thermal distortion of the mold. The stress model features an elastic-viscoplastic creep constitutive equation that accounts for the different responses of the liquid, semisolid, delta-ferrite, and austenite phases. Functions depending on temperature and composition are employed for properties such as thermal linear expansion. A contact algorithm is used to prevent penetration of the shell into the mold wall due to the internal liquid pressure. An efficient two-step algorithm is used to integrate these highly nonlinear equations. The model is validated with an analytical solution for both temperature and stress in a solidifying slab. It is applied to simulate continuous casting of a 120 mm billet and compares favorably with plant measurements of mold wall temperature, total heat removal, and shell thickness, including thinning of the corner. The model is ready to investigate issues in continuous casting such as mold taper optimization, minimum shell thickness to avoid breakouts, and maximum casting speed to avoid hot-tear crack formation due to submold bulging.     

Dealumination–aging pattern of REUSY zeolites contained in fluid cracking catalysts

The evolution of the properties of a REUSY zeolite contained in a fluid cracking catalyst was investigated under laboratory steam deactivation procedures and in age fractions of the corresponding equilibrium catalyst (Ecat). The aging pattern, defined by the evolution of the zeolite surface area (ZSA) related to the decrease of the unit cell size (UCS), was similar between lab-steamed zeolites and Ecat fractions. A sharp drop in ZSA occurred at ca. 2.430 nm UCS. A study done by FT-IR spectroscopy suggested that zeolite dealumination initially took place more extensively on the sodalite cages and double six-member rings (D6R) of the structure and that the final collapse of the zeolite framework occurred through destruction of the 12-member rings (12M). This can be explained by a crystal fracture and break down process and disassembling of the sodalite cages in the faujasite structure. NH₃ microcalorimetry showed that strong acid sites in faujasites are destroyed by steam aging, but this effect does not lead to a reduction in the cracking activity of the Ecat form. The microactivity test (MAT) showed that the specific activity declined sharply at 2.430 nm UCS. Differences in product selectivity were related to the extent of damage of the zeolite, extra-framework alumina and mesoporosity. While further aging canceled the effect attributed to extra-framework alumina differences attributed to mesoporosity increased.     

Glycoconjugated polymer 6. Synthesis of poly[styrene-<Emphasis Type="Italic">block</Emphasis>-(styrene-<Emphasis Type="Italic">graft</Emphasis>-amylose)] via potato phosphorylase-catalyzed polymerization

Summary The potato phosphorylase-catalyzed polymerization of α-D-glucose-1-phosphate (G-1-P) onto poly[styrene-block-(4-vinylbenzyl maltohexaoside)] (1) was performed at the molar ratios of [G-l-P]₀ and [maltohexaose]₀ of 35, 80, and 250. The product was found to be soluble in dimethyl sulfoxide, which was a good solvent for amylose, and showed the complex-formation with iodine, indicating that the product was assignable to poly[styrene-block-(styrene-graft-amylose)] (2). The quantitative analysis of the liberated phosphoric acid gave the average degree of polymerization o f the glucose unit (n) as 27, 5 1, and 180 for 2-I, 2-II, and 2-III, respectively. Received: 29 November 2002/Accepted: 22 December 2002 Correspondence to Toyoji Kakuchi     

The Intellectual Development of Science and Engineering Students. Part 2: Teaching to Promote Growth

As college students experience the challenges of their classes and extracurricular activities, they undergo a developmental progression in which they gradually relinquish their belief in the certainty of knowledge and the omniscience of authorities and take increasing responsibility for their own learning. At the highest developmental level normally seen in college students (which few attain before graduation), they display attitudes and thinking patterns resembling those of expert scientists and engineers, including habitually and skillfully gathering and analyzing evidence to support their judgments. This paper proposes an instructional model designed to provide a suitable balance of challenge and support to advance students to that level. The model components are (1) variety and choice of learning tasks; (2) explicit communication and explanation of expectations; (3) modeling, practice, and constructive feedback on high‐level tasks; (4) a student‐centered instructional environment; and (5) respect for students at all levels of development.     

MULTICARRIER DS—CDMA WITH ADAPTIVE MODULATION AND POWER ALLOCATION

Adaptive modulation and power allocation is introduced into the multicarrier DSCDMA system to improve the system performance and bandwidth efficiency.First,the system design appropriate for adaptive modulation and power allocation is given,then the algorithm of adaptive modulation and power allocation is applied.Simulation results demonstrate great performance improvement compared with the fixed modulated one.     

Exchange-correlation errors at harmonic and anharmonic orders: the case of bulk Cu

As an aid towards improving the treatment of exchange and correlation effects in electronic structure calculations, it is desirable to have a clear picture of the errors introduced by currently popular approximate exchange-correlation functionals. We have performed ab initio density functional theory and density functional perturbation theory calculations to investigate the thermal properties of bulk Cu, using both the local density approximation (LDA) and the generalized gradient approximation (GGA). Thermal effects are treated within the quasiharmonic approximation. We find that the LDA and GGA errors for anharmonic quantities are an order of magnitude smaller than for harmonic quantities; we argue that this might be a general feature. We also obtain much closer agreement with experiment than earlier, more approximate calculations.     

Electronic properties of magnetically doped nanotubes

Effect of doping of carbon nanotubes by magnetic transition metal atoms has been considered in this paper. In the case of semiconducting tubes, it was found that the system has zero magnetization, whereas in metallic tubes the valence electrons of the tube screen the magnetization of the dopants: the coupling to the tube is usually antiferromagnetic (except for Cr).     

Use of X-ray computed microtomography to understand why gels reduce relative permeability to water more than that to oil

X-ray computed microtomography (XMT) was used to investigate why gels reduce relative permeability to water more than that to oil in strongly water-wet Berea sandstone. XMT allows saturation differences to be monitored for individual pores during various stages of oil, water, and gelant flooding. The method also characterizes distributions of pore size, aspect ratio, and coordination number for the porous media. We studied a Cr(III) acetate–HPAM gel that reduced permeability to water (at S_or) by a factor 80–90 times more than that to oil (at S_wr). In Berea, the gel caused disproportionate permeability reduction by trapping substantial volumes of oil that remained immobile during water flooding (i.e., 43.5% S_or before gel placement versus 78.7% S_or after gel placement). With this high trapped oil saturation, water was forced to flow through narrow films, through the smallest pores, and through the gel itself. In contrast, during oil flooding, oil pathways remained relatively free from constriction by the gel.