A global output-feedback controller for stabilization and tracking of underactuated ODIN: A spherical underwater vehicle

This paper presents a method to design an output-feedback controller that simultaneously solves global asymptotic stabilization and tracking of an underactuated omni-directional intelligent navigator—a spherical underwater vehicle moving in a horizontal plane (i.e. at a constant depth). The vehicle does not have a sway actuator and has only position and orientation measurements available. The control development is based on Lyapunov's direct method, backstepping technique and use of interconnected structure of the vehicle dynamics. Numerical simulations demonstrate the results.     

Adaptive switching supervisory control of nonlinear systems with no prior knowledge of noise bounds

The problem of controlling nonlinear noisy systems affected by parametric uncertainties is approached via the introduction of a supervisor which, whenever needed, switches on, in feedback to the plant, a controller selected from a finite set of predesigned controllers. A Lyapunov-based falsification criterion allows one to ensure robust stability in the presence of uncertain constant parameters and exogenous bounded disturbances. Simulations are discussed in order to illustrate the merits of the proposed algorithms.     

Cooling of cylindrical vertical tanks submitted to natural internal convection

A numerical and an experimental analysis of velocity and temperature fields inside a storage tank submitted to natural convection is presented. The analysis was performed in two stages. In the first stage, the temperature profile along the vertical axis of the storage tank was obtained experimentally and numerically, for cooling time ranging from 45 to 60 h. The numerical analysis was carried out using a transient bi-dimensional model in cylindrical co-ordinates. In the second stage, after the numerical code validation, 40 cases of cooling with four aspect ratios, five insulation thicknesses, and two different volumes were simulated. In all simulations, thermal losses for the environment in all tank walls (side, top and bottom) were considered. Two correlations for the Nusselt number, encompassing all the forty cases, were obtained with these results.     

Stability studies on methyl and ethyl fatty acid esters of sunflowerseed oil

Fatty acid esters, high in linoleic acid, were prepared and stored for long-term engine tests. Storage tests with these esters were undertaken to obtain more information on optimal storage requirements and general stability characteristics. Samples were kept at three temperature levels (20 C, 30 C and fluctuating around 50 C) for a 90-day period and were removed at regular intervals for chemical and physical analysis. The influence of air, temperature, light, TBHQ and contact with mild steel was evaluated by comparing the free fatty acid, peroxide, anisidine, ultraviolet absorption, viscosity and induction periods. A statistical model was used to evaluate the data and to reduce the large number of data points to comparable curves. Storage of esters in contact with air, especially at a temperature above 30 C, resulted in significant increases in peroxide, ultraviolet absorption, free fatty acid, viscosity and anisidine values. Exclusion of air retarded oxidation at all temperature levels. A direct relationship between viscosity increases and oxidation parameters was evident. Exposure to light caused a small increase in the oxidation parameters of esters stored at the highest temperature level. Addition of TBHQ prevented oxidation of samples stored under moderate conditions. Under unfavorable storage conditions the anti-oxidant was no longer effective. Mild steel had very little effect on the oxidation parameters. Only the anisidine values of samples stored at the highest temperature level were slightly increased. Methyl esters performed slightly better than ethyl esters during the storage test. The following practical guidelines for storage of fatty acid ester fuels are: (i) airtight containers should be used; (ii) the storage temperature should be <30 C; (iii) mild steel (rust free) containers may be used, and (iv) TBHQ has a beneficial effect on oxidation stability.     

Frequency domain identification of Wiener models

This paper proposes a frequency domain algorithm for Wiener model identifications based on exploring the fundamental frequency and harmonics generated by the unknown nonlinearity. The convergence of the algorithm is established in the presence of white noise. No a priori knowledge of the structure of the nonlinearity is required and the linear part can be nonparametric.     

Optimised electromagnetic 3d field solver for frequencies below the first resonance

An optimised low-frequency solution algorithm is proposed that reduces the electromagnetic wave equation to a small number of scalar potential problems. The latter can be solved using black-box algebraic multigrid solvers. Within the framework of the finite integration technique, the reduction of the wave equation is accomplished by tree/cotree decompositions of primary and dual grids, which allow for highly efficient solutions of Ampere's and Faraday's equations. The example of a ferrite-loaded accelerator component demonstrates that the scheme is much more efficient than the direct approach using Krylov subspace solvers     

Position synchronization of multiple motion axes with adaptive coupling control

A new control approach to position synchronization of multiple motion axes is developed, by incorporating cross-coupling technology into adaptive control architecture. The control strategy is to stabilize position tracking of each axis while synchronizing its motion with other axes’ motions so that differential position errors amongst axes converge to zero. The proposed adaptive controller and parameter estimator employ coupling control by feeding back position errors and differential position errors, and have been realized to guarantee asymptotic convergence to zero of both position and synchronization errors. Simulations conducted on a multi-axis motion control system demonstrate the effectiveness of the method.