Effect of heat treatment in air on the thermal properties of SiC fibre reinforced composite: Part 2 A magnesium aluminium silicate (MAS) matrix glass ceramic composite

The thermal properties of a magnesium aluminium silicate (MAS) glass ceramic matrix composite reinforced by SiC (Nicalon) fibres have been investigated before and after heat treatment in the temperature range 600–1,200 °C. Within this temperature range, during the heat treatment at lower temperatures such as 600 and 700 °C, the oxidation of the carbon layer occurred and mixture of silicon and carbon was formed in the interface. This results in a decrease in thermal diffusivity values. After heat treatment at the temperatures higher than 1,000 °C, the carbon layer was thickened and resulted in the higher thermal diffusivity values.     

实验室条件下聚能射孔损害带研究

在实验室条件下对贝雷砂岩进行射孔试验,并分别对射孔后的靶体进行酸化、压裂工艺处理,利用核磁共振和工业X-CT技术分别对未射孔的靶体、射孔后的靶体、射孔后酸化的靶体、射孔后压裂的靶体进行测试.定量分析了射孔对砂岩靶体的损害及酸化、压裂对射孔损害的解除作用.     

克拉-2气田射孔工艺研究

克拉-2气田具有5大射孔难题:射孔井段长、地层压力大、产气量大、流体中腐蚀性物质和不宜丢枪,作业风险非常大。提出了带枪生产的射孔方案和射孔后取枪生产2种射孔方案,通过分析对比优选出最佳方案——最终选定模块式射孔枪过油管方案,并对该方案作了较为详尽的叙述,在后来的施工中成功地得到了印证。     

Measurement of the density and surface tension of Ni-based superalloys in the liquid and mushy states

The densities of three Ni-based superalloys have been measured in both liquid and mushy states by both a modified sessile drop method (MSDM) and a modified pycnometric method (MPM) for alloys CMSX-4 and CM186LC, and for CMSX-10 alloy by MSDM only. The surface tensions of liquid CMSX-4, CM186LC, and CMSX-10 superalloys were measured using the sessile drop method. All measurements were carried out in a highly purified argon atmosphere with the oxygen partial pressure of less than 10⁻¹⁹ MPa in the gas outlet. The densities of all superalloys in both liquid and mushy states were found to decrease with increasing temperature. The volume thermal expansion of each superalloy in the mushy state was found to be higher than that in the liquid state. The densities determined by different methods have been critically assessed and recommended values in both liquid and mushy states are given as a linear function of temperature for the three Ni-based superalloys. The surface tension of liquid CMSX-4 superalloy was found to decrease with increasing temperature, while that of liquid CMSX-10 superalloy increases with increasing temperature. The wetting behavior of liquid CM186LC on the alumina substrate was found (1) to differ significantly from that of CMSX-4 and CMSX-10 and (2) to vary with time. A HfO₂-rich layer was found in the contact area of CM186LC with the alumina substrate, which could lead to some uncertainty in the value obtained for the surface tension determined for CM186LC.     

Experimental determination of NH<Subscript>4</Subscript>NO<Subscript>3</Subscript>-KNO<Subscript>3</Subscript> binary phase diagram

The solid-state phase transitions in ammonium nitrate (AN)-potassium nitrate (KN) system, and the equilibrium AN-KN phase diagram have been determined by using differential scanning calorimetry and high-temperature in situ x-ray diffractometry. Sample preparation was performed in a special “dry room” with very low humidity. A single phase region (AN III) with no phase transitions to 373 K was observed in the composition range 5 to 20% KN; this is critical for use in air bag gas generators. The high-temperature KN phase (KN I) has a wide range of stability from 20 to 100 wt.% KN. There are one eutectic, two eutectoid, three peritectoid, and one congruent transformations in this phase diagram. Two new nonstoichiometric phases were found at lower temperatures in the mid-composition range between the AN and KN terminal solid solutions. Details of the phase equilibria are presented.     

铁路桥梁横向振动模拟及适应快速行车结构型式的研究

针对铁路提速后出现的上承式简支钢板梁桥跨中横向振幅过大的问题,以羊楼司桥(L=32m单跨上承式简支钢板梁桥)为例进行实桥检测和数值模拟,建立车辆、线路、桥梁三者的联合模型,考虑轮轨接触力,应用MSC/DYTRAN大型结构分析程序进行车线桥动力相互作用的仿真分析。研究揭示我国用量最多的C62型货车以70∽80km/h的速度空载通过时,该跨度的钢板梁桥发生横向谐振的机理。此外,用该方法对32m跨长的组合梁结构进行桥梁动力特性及列车走行性分析,表明该结构满足提速货车和高速电动旅客列车走行的要求。研究结果对我国高速铁路桥梁建设和既有桥梁的改造具有积极意义。     

Three-phase self-excited induction generators: an overview

Induction generators are increasingly being used in nonconventional energy systems such as wind, micro/mini hydro, etc. The advantages of using an induction generator instead of a synchronous generator are well known. Some of them are reduced unit cost and size, ruggedness, brushless (in squirrel cage construction), absence of separate dc source, ease of maintenance, self-protection against severe overloads and short circuits, etc. In isolated systems, squirrel cage induction generators with capacitor excitation, known as self-excited induction generators (SEIGs), are very popular. This paper presents an exhaustive survey of the literature over the past 25 years discussing the process of self-excitation and voltage buildup, modeling, steady-state, and transient analysis, reactive power control methods, and parallel operation of SEIG.     

Microstructures formed by spray freezing of food fats

The spray-freezing of two food fats, tripalmitin (PPP) and cocoa butter (CB) and mixtures thereof, has been modeled experimentally using a novel single droplet freezing apparatus configured so that temperature profiles or samples for microstructure analysis can be obtained. For 2 mm diameter droplets suspended in a cold air flow at temperatures around 2–15°C, initial cooling rates were on the order of 10 K s⁻¹ and the temperature profiles could be correlated directly to DSC data collected at 20 K min⁻¹, indicating that minimal supercooling of the materials occurred in the droplet form. Microstructure analysis confirmed that PPP crystallized preferentially in mixtures, and that the surface structure was very sensitive to storage conditions. The bulk structure was much less sensitive, and the internal microstructure of the PPP droplets revealed distinct nucleation sites, which were absent from the CB: These persisted in the mixtures up to 50 wt%. X-ray analysis indicated that the fats crystallized in their more stable forms, namely, β for PPP and Form V/V1 in CB.     

Modeling for local dynamic behaviors of phenol biodegradation in bubble columns

A coupled three-dimensional (3-D) model, combining hydrodynamics with biochemical reactions, was developed to simulate the local transient flow patterns and the dynamic behaviors of cell growth and phenol biodegradation by yeast Candida tropicalis in the bubble-column bioreactor, using the computational fluid dynamic (CFD) method. In order to validate this proposed model effectively, the validation of the local hydrodynamic characteristics of the gas-mineral salt solution (gas-liquid) two-phase system, with the phenol concentration of 1200 mg/L, and with the absence of cells, was performed in a square-sectioned bubble column bioreactor using the LDA system and conductivity probe. Furthermore, the validation of phenol biodegradation behaviors by yeast Candida tropicalis at different initial concentrations of phenol and cell was also carried out in the above bubble-column bioreactor. The results indicated that the model simulations had a satisfying agreement with the experimental data. Finally, the local instantaneous flow and phenol biodegradation features including gas holdup, gas velocity, liquid velocity, cell concentration and phenol concentration inside the bioreactor were successfully predicted in different-scale bubble columns by the proposed model. © 2006 American Institute of Chemical Engineers AIChE J, 2006     

Growth of highly orientated strontium barium niobate thin films on Si substrates through the sol–gel process using a K: SBN template layer

We report the growth of highly C-axis orientation of Sr _x Ba_1−x Nb₂O₆ (SBN) thin films on p-type (100) Si substrates by using a potassium-substituted SBN template layer with the sol–gel method. The crystallization of SBN thin films was found closely related to the potassium ion doping concentration and the postannealing temperature of the K-SBN template layer. Secondary ion mass spectrometry analysis showed that potassium elements were accumulated at the interface of the template layer and silicon substrate. SBN films postannealed at 750 °C with K-SBN template layer has a smaller full width at half maximum of X-ray rocking curve of 2.45° than that of 5.40° for the pure SBN films. By introducing a template layer, the surface morphologies of SBN films fabricated on silicon substrate were greatly improved.