International Working Group on Assurance Cases (for Security)

Critical systems are aptly named - from electric power to water and gas to the telephone system and the Internet, they're all critical to some aspect of our daily lives. We're a networked society and as such, it's important to both know whether critical systems are trustworthy and be able to communicate, review, and debate the level of trust achieved in them. In the safety domain, explicit safety cases are increasingly required by law, regulations, and standards. In this article, we outline what a small, international group of experts, spanning various disciplines in safety, security, reliability, and critical infrastructure, been doing with the International Working Group on Assurance Cases (for Security), what we hope to achieve, and where we go next.     

A concise process technology for 3-D suspended radio frequency micro-inductors on silicon substrate

In this letter, a concise process technology is proposed for the first time to enable the fabrication of good quality three-dimensional (3-D) suspended radio frequency (RF) micro-inductors on bulk silicon, without utilizing the lithography process on sidewall and trench-bottom patterning. Samples were fabricated to demonstrate the applicability of the proposed process technology.     

Security issues for downloaded code in mobile phones

'Software defined radio' (SDR) is a technology that will appear in future generations of mobile phones, i.e. following the third-generation mobile phone technology that is currently being defined and developed. Early versions of 'pragmatic' SDR will allow the terminal to be reconfigured at any level of its protocol stack. Ultimately, the 'pure' SDR technology will allow a mobile phone or terminal to have its air interface software configured or reconfigured by other software (or software parameters) that have been downloaded to the terminal, e.g. over the air, or from a remote server via the Internet and one's personal computer (PC). A number of security issues arise with downloaded code that implements the air interface functions, and these may not be obvious simply from looking at the way PC software is updated on-line today. This paper starts with an outline of the code that allows a mobile phone to operate over a particular air interface. This sets the baseline for a discussion of the security issues surrounding the change of this code from one that is fixed and downloaded once only, to code that is reconfigurable during the life of a product.     

Reliability prediction models to support conceptual design

During the early stages of conceptual design, the ability to predict reliability is very limited. Without a prototype to test in a lab environment or without field data, component failure rates and system reliability performance are usually unknown. A popular method for early reliability prediction is to develop a computer model for the system. However, most of these models are extremely specific to an individual system or industry. This paper presents three general procedures (using both simulation and analytic solution techniques) for predicting system reliability and average mission cost. The procedures consider both known and unknown failure rates and component-level and subsystem-level analyzes. The estimates are based on the number of series subsystems and redundant (active or stand-by) components for each subsystem. The result is a set of approaches that engineers can use to predict system reliability early in the system-design process. Software was developed (and is discussed in this paper) that facilitates the application of the simulation-based techniques. For the specific type of system and mission addressed in this paper, the analytic approach is superior to the simulation-based prediction models. However, all three approaches are presented for two reasons: (1) to convey the development process involved with building these prediction tools; and (2) the simulation-based approaches are of greater value as the research is extended to consider more complex systems and scenarios     

Deformation behavior of HCP Ti-Al alloy single crystals

Single crystals of Ti-Al alloys containing 1.4, 2.9, 5, and 6.6 pct Al (by weight) were oriented for 〈a〉 slip on either basal or prism planes or loaded parallel along the c-axis to enforce a nonbasal deformation mode. Most of the tests were conducted in compression and at temperatures between 77 and 1000 K. Trace analysis of prepolished surfaces enabled identification of the twin or slip systems primarily responsible for deformation. Increasing the deformation temperature, Al content, or both, acted to inhibit secondary twin and slip systems, thereby increasing the tendency toward strain accommodation by a single slip system having the highest resolved stress. In the crystals oriented for basal slip, transitions from twinning to multiple slip and, finally, to basal slip occurred with increasing temperature in the lower-Al-content alloys, whereas for Ti-6.6 pct Al, only basal slip was observed at all temperatures tested. A comparison of the critically resolved shear stress (CRSS) values for basal and prism slip as a function of Al content shows that prism slip is favored at room temperature in pure Ti, but the stress to activate these two systems becomes essentially equal in the Ti-6.6 pct Al crystals over a wide range of temperatures. Compression tests on crystals oriented so that the load was applied parallel to the c-axis showed extensive twinning in lower Al concentrations and 〈c+a〉 slip at higher Al concentrations, with a mixture of 〈c+a〉 slip and twinning at intermediate compositions. A few tests also were conducted in tension, with the load applied parallel to the c-axis. In these cases, twinning was observed, and the resolved shear for plastic deformation by twinning was much lower that that for 〈c+a〉 slip observed in compression loading. This article is based on a presentation made in the symposium entitled “Defect Properties and Mechanical Behavior of HCP Metals and Alloys” at the TMS Annual Meeting, February 11–15, 2001, in New Orleans, Louisiana, under the auspices of the following ASM committees: Materials Science and Critical Technology Sector, Structural Materials Division, Electronic, Magnetic & Photonic Materials Division, Chemistry & Physics of Materials Committee, Joint Nuclear Materials Committee, and Titanium Committee.     

Sequential tripping strategy for a transmission network back-upprotection expert system

This paper describes a sequential tripping strategy used in a wide area back-up protection expert system (BPES) to combat situations in which protection relays have maloperated or information is missing. The BPES is an innovative back-up protection scheme designed to prevent the occurrence of widespread blackouts. The BPES evaluates the certainty that transmission lines are likely to be affected by the fault and uses a sequential tripping strategy to isolate the fault if a firm decision is not available due to maloperated relays and/or missing information. The mode of analysis and the sequential tripping strategy ensures that the BPES will clear a fault at minimum risk to the network. An example is included to demonstrate how the certainty factor based sequential tripping strategy is employed by the BPES to clear a fault which occurred on the South Western part of the UK National Grid System     

Flotation machine design: impeller—stator interaction

The separate contributions of impellers and stators to suction are studied by means of interaction models. From these, suction can be predicted when interchangeable components are used in any combination, and in either direction of impeller rotation. Methods are devised by which numerical values of the impeller and stator terms can be simply assigned. The resulting model provides good agreement with experiment. The influence of variability in component geometry is reflected in the model parameters. Possible applications of the model are suggested.