Influence of post‐treatments on the properties of porous poly(vinyl alcohol) membranes

Porous poly(vinyl alcohol) (PVA) membranes were prepared by a phase‐inversion method. The influence of chemical crosslinking and heat treatments on the swelling degree, resistance to compaction, mechanical strength, and morphology of porous PVA membranes was extensively studied. The crosslinking degree and crystallinity of the membranes, calculated from IR spectra, increased with the treatment time. The porosity, calculated on the basis of swelling experiments, showed a decreasing trend for heat‐treated membranes but remained almost at a constant value for crosslinked membranes. Such a change was further proved with scanning electron microscopy pictures. The behavior was explained by the rearrangement of PVA chains during the heat‐treatment process, which led to morphological changes in the membranes. The mechanical properties of the porous membranes in dry and wet states were measured, and a great difference was observed between crosslinked and heat‐treated membranes in the dry and wet states. The crosslinked membranes showed good mechanical properties in the dry state but became fragile in the wet state. On the contrary, the heat‐treated membranes were more flexible in the wet state than in the dry state. This change was explained by the turnaround of inner stress in the systems during the swelling process. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Accelerated wear testing with a microfabricated surface to evaluate the lubrication ability of biomolecules on polyethylene

Wear of ultrahigh‐molecular‐weight polyethylene (UHMWPE) and wear‐particle‐induced osteolysis and bone resorption are the major factors causing the failure of total joint replacements. It is feasible to improve the lubrication and reduce the wear of artificial joints. We need further understanding of the lubrication mechanism of the synovial fluid. The objective of this study is to evaluate the lubricating ability of three major components in the synovial fluid: albumin, globulin, and phospholipids. An accelerated wear testing procedure in which UHMWPE is rubbed against a microfabricated surface with controlled asperities has been developed to evaluate the lubrication behavior. An analysis of the wear particle dimensions and wear amount of the tests has provided insights for comparing their lubrication performance. It is concluded that the presence of biomolecules at the articulating interface may reduce friction. A higher concentration of a biological lubricant leads to a decrease in the wear particle width. In addition, in combination with the wear results and mechanical analysis, the roles of individual biomolecules contributing to friction and wear at the articulating interface are discussed. These results can help us to identify the role of the biomolecules in the boundary lubrication of artificial joints, and further development of lubricating additives for artificial joints may be feasible. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

橡胶Mooney—Rivlin模型材料系数对轴向刚度影响分析

在橡胶小变形范围内，采用理论推断的方法，得到在相同硬度下橡胶Mooney—Rivlin模型材料系数由C2／C1决定的关系式。并采用ABAQUS有限元软件分析的方法，结合橡胶轴向刚度常规解，分析了C2／C1不同值对橡胶轴向刚度的影响进行，结果显示其影响呈现一定规律性。     

CO毒化AB5型合金分形特征研究

研究了三种贮氢合金 L a Ni5、L a Ni4 .7Al0 .3、Ml Ni4 .5Al0 .5被 10 0× 10 - 6 CO毒化后的分形特征 ,求出这三种合金在含 10 0× 10 - 6 CO的氢中循环 ,分维分别为 0 .2 5 4 7、0 .170 9、0 .0 72 5。可以较好的解释合金被毒化的宏观现象。     

乙烯裂解炉对流段局部结构设计改进

介绍了乙烯裂解炉对流段的结构功能,各部件局部结构的改善设计。     

使用IP/NetBEUI组合协议建造跨VLAN的VoD网站的方法

介绍一种使用IP和NetBEUI组合协议建造Intranet内部VoD（视频点播）网站的简 便技术。并已成功地运用这一技术建成了莆田学院的VoD网站。     

钾基CO2吸收剂的碳酸化反应特性

对钾基CO2吸收剂的碳酸化反应机理进行研究.利用热重分析、XRD、扫描电镜和氮吸附仪进行试验.结果表明:分析纯碳酸钾的组分为K2CO3·1.5H2O,碳酸化反应速率缓慢;先将分析纯碳酸钾样品脱除结晶水后再进行碳酸化反应时,K2CO3与气氛中的水蒸气迅速生成K2CO3·1.5H2O,不利于碳酸化反应的进行;由KHCO3分解产生的K2CO3却表现出优越的碳酸化反应性能,20 min内转化率高达85%以上,经过多次循环试验后吸收剂仍保持很高的活性.从微观角度分析了两种改性钾基CO2吸收剂碳酸化反应机理差异的原因,通过拟合计算得到了这3种钾基吸收剂的碳酸化反应速率常数,为干法K2CO3/KHCO3循环脱除CO2的研究提供了一定的基础数据.     

A Newly Developed Non, Destructive Tritium Measurement Technique and Its Application to V-4Cr-4Ti Alloy

A non-destructive and in-situ technique for the measurement of tritium in materials, namely β-ray-induced X-ray spectrometry （BIXS）, has been developed recently. In the present study a V-4Cr-4Ti alloy was pre-heated at 1000℃ for 2 h to form a recrystallization structure before the tritium absorption experiments were conducted. Firstly the hydrogen isotope gas was charazterized by means of a quadrupole mass spectrometer （QMS） and a small-sized ionization chamber. Then hydrogen isotope absorption tests of V-4Cr-4Ti alloy were performed at 400 ℃ and the atomic concentration of hydrogen isotope in V-4Cr-4Ti alloy was estimated as 0.17% with a tritium content of approximately 2.5 ppm. Experimental results indicate that BIXS is a quite useful tool for quantitatively measuring the tritium content and tritium distribution in the surface layers of vanadium alloys and no strong trapping effects of tritium exist in the pre-heated V-4Cr-4Ti alloy.