Carotid-jugular arteriovenous fistula and cerebrovascular infarct: a case report of an iatrogenic complication following internal jugular vein catheterization

Central venous catheterization is frequently performed for perioperative management and long-term intravenous access. Although complications associated with central venous catheter insertion have been widely reported, there are few reports of carotid-jugular arteriovenous fistula formation. Endovascular procedures are associated with a risk of immediate and delayed thromboembolic and ischemic complications. We describe a case of a carotid-jugular arteriovenous fistula and a cerebrovascular infarct following the insertion of a double-lumen catheter for hemodialysis access. We provide recommendations for the prevention and the early detection of this iatrogenic complication.     

Synthesis,conductivity and dielectric characterization of salicylic acid–Fe3O4 nanocomposite

We report on the synthesis of water dispersible salicylic acid –Fe₃O₄ nanocomposites via a co-precipitation route by using Fe(III) and Fe(II) chloride salts, and salicylic acid. Crystalline phase was identified as Fe₃O₄ and the crystallite size was obtained as 13 ± 6 nm from X-ray line profile fitting. As compared to the particle size of 20 nm obtained from TEM analysis these particles show polycrystalline nature. The capping of salicylic acid around Fe₃O₄ nanoparticles was confirmed by FTIR spectroscopy, the interaction being via bridging oxygens of the carboxylate and the nanoparticle surface. ac and dc conductivity measurements performed on the nanocomposite revealed semiconductor characteristics and varying trends with temperature due to reorganization of the nanocomposite. Permittivity measurements showed increasing dielectric constant with increasing temperature as expected from semiconductors. Analysis of electrical modulus and dielectric permittivity functions suggest that ionic and polymer segmental motions are strongly coupled in the nanocomposite.     

Microfabricated Biomaterials for Engineering 3D Tissues

Mimicking natural tissue structure is crucial for engineered tissues with intended applications ranging from regenerative medicine to biorobotics. Native tissues are highly organized at the microscale, thus making these natural characteristics an integral part of creating effective biomimetic tissue structures. There exists a growing appreciation that the incorporation of similar highly organized microscale structures in tissue engineering may yield a remedy for problems ranging from vascularization to cell function control/determination. In this review, we highlight the recent progress in the field of microscale tissue engineering and discuss the use of various biomaterials for generating engineered tissue structures with microscale features. In particular, we will discuss the use of microscale approaches to engineer the architecture of scaffolds, generate artificial vasculature, and control cellular orientation and differentiation. In addition, the emergence of microfabricated tissue units and the modular assembly to emulate hierarchical tissues will be discussed.     

Fast and Highly Sensitive Ionic‐Polymer‐Gated WS2–Graphene Photodetectors

The combination of graphene with semiconductor materials in heterostructure photodetectors enables amplified detection of femtowatt light signals using micrometer‐scale electronic devices. Presently, long‐lived charge traps limit the speed of such detectors, and impractical strategies, e.g., the use of large gate‐voltage pulses, have been employed to achieve bandwidths suitable for applications such as video‐frame‐rate imaging. Here, atomically thin graphene–WS₂ heterostructure photodetectors encapsulated in an ionic polymer are reported, which are uniquely able to operate at bandwidths up to 1.5 kHz whilst maintaining internal gain as large as 10⁶. Highly mobile ions and the nanometer‐scale Debye length of the ionic polymer are used to screen charge traps and tune the Fermi level of the graphene over an unprecedented range at the interface with WS₂. Responsivity R = 10⁶ A W^?1 and detectivity D* = 3.8 × 10¹¹ Jones are observed, approaching that of single‐photon counters. The combination of both high responsivity and fast response times makes these photodetectors suitable for video‐frame‐rate imaging applications.     

Calibration of Expert Judgments Applied to Uncertainty Assessment

Abstract:

This article contributes a methodology for eliciting expert judgment in support of decision analysis associated with the conceptual design of advanced engineering systems. To provide a basis for decision making in the presence of model and input parameter uncertainties, experts in several disciplines can be utilized to provide model parameter estimates to facilitate analyses. The judgment elicitation methodology was developed to cover a multitude of system disciplines using multiple experts. To address consistency in expert assessments, the methodology includes expert assessment calibration means. A sample application of the resultant expert judgment methodology is discussed. An engineering manager can use the methodology described in this article to assess viability of potential courses of action in high-risk or advanced state-of-the-art technology systems development ventures.     

Abrasive Wear Volume Maps for PA6 and PA6 Composites Under Dry Working Condition

In this study the wear volume map is obtained and considered for evaluation of the abrasive wear performance for polyamide (PA6) and PA6 composites. Polyamide composites were tailored using 25 wt.% glass bead, 20 wt.% talc and 30 wt.% wollastonite fillers. In this work, the influence of filler materials, abrasion surface roughness and applied loading values on abrasive wear performance of PA6 and PA6 composites were evaluated. Experimental abrasive wear tests were carried out at atmospheric condition using pin-on-disc rig arrangement. Tests were performed under 4, 6, 8 and 10 N load values, traveling speed of 1 m/s and abrasion surface roughness values of 5, 20 and 45 μm. Wear volume maps were obtained and the results showed that the lowest wear volume rate for PA is reached using glass bead filler. Furthermore, the results also showed that the higher is the applied load and the roughness of the abrasion surface, the higher is the wear rate. Finally it is also concluded that abrasive wear process mechanism include ploughing mechanism and delimitation of filler tips.