Ice-slurry production using direct contact heat transfer

An ice slurry generation system was developed using direct contact heat transfer between water and the coolant, Fluroinert FC-84. The location of the coolant nozzle is an important design consideration to avoid clogging due to freezing of water. An ice fraction of up to about 40 percent was obtained with the nozzle located at the bottom of the ice slurry tank and the jet directed upwards into the water. Two simplified model were developed to extract the heat transfer coefficient between the coolant drops and the water. The first model requires as input the average drop diameter and the residence time while the second model uses the measured drop diameter distribution. The estimated heat transfer coefficients are much smaller than those computed using single-sphere correlations.     

Control of calcium hexaluminate grain morphology in in-situ toughened ceramic composites

The influence of processing conditions on the morphology of calcium hexaluminate (CA₆) grains in Al₂O₃: 30 vol% CaO·6Al₂O₃ (CA₆) ceramic composites was investigated. Specimens were prepared by in-situ reaction sintering using precursor powders of alumina, and either calcium carbonate or calcium oxide. In some samples, 1 vol% anorthite glass was added as a sintering aid. X-ray diffraction was used to study the phase development in the as-calcined and sintered states. The resultant microstructures were characterized using both scanning electron microscopy (SEM), and imaging secondary ion mass spectrometry (SIMS). It was found that the CA₆ grains developed a platelike morphology when CaCO₃ was used as the starting calcium-rich powder. In contrast, samples prepared using CaO resulted in equiaxed CA₆ grains. This result was observed to be independent of the anorthite glass addition. The findings are rationalized in terms of distinct CA₆ reaction mechanisms, resulting from differences in the reactivity of the powders during the early stages of calcining.Cement Nomenclature C CaO - A Al₂O₃     

Mechanomyography and oxygen consumption during incremental cycle ergometry

Brucella abortus strain RB51 was recently approved as an official brucellosis calfhood vaccine for cattle by the Animal and Plant Health Inspection Service branch of the United States Department of Agriculture. Currently available serologic surveillance tests for B. abortus do not detect seroconversion following SRB51 vaccination. The purpose of this study was to evaluate a dot-blot assay using gamma-irradiated strain RB51 bacteria for its specificity and sensitivity to detect antibody responses of cattle vaccinated with strain RB51. Dot-blot titers of sera at a recommended dosage (10(10) colony-forming units) were similar to those of sera from cattle vaccinated with similar numbers of B. abortus strain 19 and greater (P < 0.05) than titers of nonvaccinated cattle. In the first 12 weeks after vaccination with 10(10) colony-forming units of strain RB51, the RB51 dot-blot assay had 100% specificity for titers of 80 or less and a 53% sensitivity for titers of 160 or greater. Sensitivity of the RB51 dot-blot assay peaked at 4 weeks after vaccination with 10(10) colony-forming units of strain RB51. Dot-blot responses of sera from cattle vaccinated with a reduced dosage of strain RB51 (10(9) colony-forming units) did not differ (P > 0.05) from titers of sera from nonvaccinated cattle. Following intraconjunctival challenge with B. abortus strain 2308, titers on the RB51 dot-blot assay did not differ (P > 0.05) between nonvaccinated cattle and cattle vaccinated at calfhood with strain 19 or strain RB51.     

An eight‐node hybrid‐stress solid‐shell element for geometric non‐linear analysis of elastic shells

This paper presents eight‐node solid‐shell elements for geometric non‐linear analysis of elastic shells. To subdue shear, trapezoidal and thickness locking, the assumed natural strain method and an ad hoc modified generalized laminate stiffness matrix are employed. A selectively reduced integrated element is formulated with its membrane and bending shear strain components taken to be constant and equal to the ones evaluated at the element centroid. With the generalized stresses arising from the modified generalized laminate stiffness matrix assumed to be independent from the ones obtained from the displacement, an extended Hellinger–Reissner functional can be derived. By choosing the assumed generalized stresses similar to the assumed stresses of a previous solid element, a hybrid‐stress solid‐shell element is formulated. Commonly employed geometric non‐linear homogeneous and laminated shell problems are attempted and our results are close to those of other state‐of‐the‐art elements. Moreover, the hybrid‐stress element converges more readily than the selectively reduced integrated element in all benchmark problems. Copyright © 2002 John Wiley & Sons, Ltd.     

Analysis of adaptive routing schemes in multirate loss networks

As technology evolves, it is now feasible to implement sophisticated adaptive routing schemes on networks which support different kinds of services with heterogeneous bandwidth characteristics. Adaptive routing can increase the network throughput by routing calls to less congested paths. It can also be used to bypass transmission facility failures. In this paper, we analyze and compare two adaptive routing schemes. The first is called theMaximum mean time to blocking (MTB) routing which is based on themean time to blocking measure of a link. This measure captures the traffic rates, bandwidth characteristic and link capacity information and reflects more accurately the congestion status of different paths. The second is theM ² routing, which is a modification of the least loaded routing (LLR). Aggregation of link status information can significantly reduce signalling traffic. We show in this paper that with properly designed aggregation, the aggregatedM ² and MTB routings can have performance that approach that of the non-aggregated schemes. The use of complete sharing and restricted access policies together with trunk reservation control in multirate loss networks are also studied.     

Optical gain of interdiffused InGaAs-As and AlGaAs-GaAs quantumwells

We have analyzed theoretically the effects of interdiffusion on the gain, differential gain, linewidth enhancement factor, and the injection current density of In_0.2Ga_0.8As-GaAs and Al_0.3Ga_0.7As-GaAs quantum-well (QW) lasers. We have calculated the electron and hole subband structures including the effects of valence band mixing and strains. The optical gain is then calculated using the density matrix approach. Our results show that the gain spectrum can be blue-shifted without an enormous increase in the injected current density. Imposing an upper limit (416 A·cm^-2) on the injection current density for a typical laser structure, we find that the InGaAs-GaAs and AlGaAs-GaAs QW lasers can be blue-shifted by 24 and 54 mn, respectively. Our theoretical results compare well with the tuning ranges of 53 and 66 meV found for AlGaAs-GaAs QWs in some experiments. This indicates that the interdiffusion technique is useful for the tuning of laser operation wavelength for multiwavelength applications     

Triangular ray-tube analysis of dielectric lens antennas

A new method of analysis for the radiation characteristics of dielectric lens antennas with arbitrary inner and outer surfaces is presented. The analysis is based on representing the feed illumination by a contiguous set of ray tubes and including the effects of surface reflections and ray divergence. Radiation patterns and the antenna gain are then computed by evaluating the closed-form expressions developed for the Kirchhoff's integral of the aperture fields. The validity of the analysis method has been demonstrated by comparing the computations with measured results of two different spherical lenses and a shaped lens configurations. The analysis method presented takes into account some of the practical aspects associated with lens design such as surface zoning to reduce the mass and surface matching to minimize the reflection loss