Cloning of cDNAs encoding xenopus neuregulin: expression in myotomal muscle during embryo development

The ontogeny of the myotome was investigated using [3H]thymidine or Brdu treatment in conjunction with 1,1', di-octadecyl-3, 3, 3', 3',-tetramethylindo-carbocyanine perchlorate (DiI) labeling and expression of specific markers. We have identified a subset of early post-mitotic cells that is present in the dorsomedial aspect of epithelial somites and is homogeneously distributed along their entire rostrocaudal extent. The post-mitotic quality of this cell subset enabled us to trace their fate in time-course experiments. Following initial somite dissociation, this epithelial post-mitotic layer bends underneath the medial portion of the nascent dermomyotome. Then, these cells progressively lose epithelial arrangement and migrate in a rostral direction where they accumulate temporarily. Subsequently, these early post-mitotic precursors extend processes that reach both rostral and caudal edges of each segment. Medial somite-derived myofibers also fill the entire mediolateral extent of the segment and reach the dorsomedial lip of the dermomyotome, thus forming the primary myotome. During this process, their large nuclei localize to a narrow stripe in the middle of the nascent myotome. Consistent with the proliferation studies, DiI labeling of the medial epithelial somite cells gave rise to a primary myotomal structure, and continuous pulsing of the DiI-injected embryos with radioactive thymidine revealed that these fibers indeed developed from post-mitotic progenitors. As these early post-mitotic cells that arise prior to somite dissociation are the first wave of progenitors that constitutes the myotome, we have termed them avian muscle pioneers. We propose that the primary myotome formed by the muscle pioneers constitutes a longitudinal scaffold that serves as a substrate for the addition of subsequent waves of myotomal cells.     

An amphiphilic conjugate approach toward the design and synthesis of betulinic acid-polyphenol conjugates as inhibitors of the HIV-1 gp41 fusion core formation

Exploration of potent inhibitors of the HIV-1 gp41 fusion core formation is a promising strategy to discover small-molecule HIV-1 entry inhibitors for the treatment of HIV-1 infection. In this paper, a series of novel betulinic acid-polyphenol conjugates was designed, guided by molecular modeling of the binding of betulinic acid (BA) and phenolic galloyl/caffeoyl groups in the groove on the gp41 N-terminal heptad repeat (NHR) trimeric coiled coil. These conjugates were synthesized via conjugation of galloyl and caffeoyl groups with BA at the C-28 position. Their inhibitory activities of HIV gp41 six-helix bundle (6-HB) formation between the NHR peptide N36 and the C-terminal heptad repeat (CHR) peptide C34 were evaluated with size-exclusion HPLC. Conjugates bearing a galloyl group were found to exhibit four to sixfold higher inhibitory activities than that of parent compound BA, suggesting that they may be exploitable as HIV-1 fusion/entry inhibitors targeting gp41. The docking study on BA and its derivatives suggests that hydrophobic and hydrogen-bonding pockets exist in the groove of the gp41 NHR trimeric coiled coil and that a potent inhibitor should have amphiphilic structures to cooperatively interact with both pockets. This possibility was explored by incorporating both lipophilic and hydrophilic groups into the conjugates in a well-defined orientation to bind with both pockets in the gp41 NHR-trimer.     

Electrospun poly(L‐lactide)/poly(ε‐caprolactone) blend fibers and their cellular response to adipose‐derived stem cells

Polymer blending is one of the most effective methods for providing new, desirable biocomposites for tissue‐engineering applications. In this study, electrospun poly(L ‐lactide)/poly(ε‐caprolactone) (PLLA/PCL) blend fibrous membranes with defect‐free morphology and uniform diameter were optimally prepared by a 1 : 1 ratio of PLLA/PCL blend under a solution concentration of 10 wt %, an applied voltage of 20 kV, and a tip‐to‐collector distance of 15 cm. The fibrous membranes also showed a porous structure and high ductility. Because of the rapid solidification of polymer solution during electrospinning, the crystallinity of electrospun PLLA/PCL blend fibers was much lower than that of the PLLA/PCL blend cast film. To obtain an initial understanding of biocompatibility, adipose‐derived stem cells (ADSCs) were used as seed cells to assess the cellular response, including morphology, proliferation, viability, attachment, and multilineage differentiation on the PLLA/PCL blend fibrous scaffold. Because of the good biocompatibility and nontoxic effect on ADSCs, the PLLA/PCL blend electrospun fibrous membrane provided a high‐performance scaffold for feasible application in tissue engineering using ADSCs. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

The effect of platinum on the performance of WO3 nanocrystal photocatalysts for the oxidation of Methyl Orange and iso‐propanol

BACKGROUND: This research investigated the effect of platinum (Pt) on the reactivity of tungsten oxide (WO₃) for the visible light photocatalytic oxidation of dyes. RESULTS: Nanocrystalline tungsten oxide (WO₃) photocatalysts were synthesised by a sol‐gel process and employed for the photocatalytic degradation of Methyl Orange under visible light. For comparison commercial bulk WO₃ materials were also studied for the same reaction. These materials were fully characterised using X‐ray diffraction (XRD), UV‐visible diffuse reflection spectroscopy and transmission electron microscopy (TEM). The photocatalytic oxidation of iso‐propanol was used as a model reaction to follow the concomitant reduction of molecular oxygen. No reactions occured in the absence of platinum, which is an essential co‐catalyst for the multi‐electron reduction of oxygen. The platinised WO₃ catalysts were stable for multiple oxidation–reduction cycles. The results from the catalytic activity measurements showed that platinised nanocrystalline WO₃ is a superior oxidation photocatalyst when compared with bulk WO₃. Methyl Orange was completely decolourised in 4 h. CONCLUSIONS: The enhanced performance of nanocrystalline Pt‐WO₃ is attributed to improved charge separation in the nanosized photocatalyst. Platinum is an essential co‐catalyst to reduce oxygen. This photocatalyst could be applied to the treatment of organic pollutants in wastewater, with the advantage of using visible light compared with the widely studied TiO₂, which requires UV light. Copyright © 2011 Society of Chemical Industry     

The formation of β‐polypropylene crystals in a compatibilized blend of isotactic polypropylene and polyamide‐6

Compatibilized polypropylene (PP)/polyamide (PA6) blends with and without β nucleating agent (β‐NA) are prepared, and are designated as Blend‐0.3 and Blend‐0, respectively. The melting and crystallization characteristic of the blends crystallized under different cooling rates and different crystallization temperatures are studied. It is observed that high β‐PP content can be developed in Blend‐0.3 only at slow cooling rates (<5°C/min), whereas high α‐PP content is formed at fast cooling rates. Isothermal crystallization analysis of Blend‐0 indicates that PA6 is an effective NA for α‐PP in the lower temperature range, whereas the α‐nucleating effect disappears in the higher temperature range. Blend‐0.3 can, therefore, be viewed as a system containing both α‐ and β‐NAs, simultaneously. PA6 is competing with β‐NA in inducing PP crystallization. Under the normal injection of Blend‐0.3, the melt will be cooled through the higher temperature that favors the effectiveness of β‐NA rapidly because of the faster cooling rate. However, the α‐nucleation effect from PA6 predominate at the lower temperature. This explains the difficulty in obtaining high β‐PP content in Blend‐0.3 from injection molding. POLYM. ENG. SCI., 2011. © 2010 Society of Plastics Engineers     

Elevated temperature nanoindentation behaviour of polyamide 6

It has been found, in this study, that there is no close correlation between the tensile and nanoindentation moduli of polyamide 6 (PA6) at high temperatures. It is demonstrated that heat modifies the surface of PA6 specimens, but its effect on the nanomechanical properties is minor. The main spurious factor which affects the nanoindentation results is adhesion, especially at low indentation depths. The overestimation in the measured indentation moduli can be corrected by performing indentations with loads high enough so that the modulus is independent of the applied load. It is concluded that the lack of strict correlations between the tensile and indentation moduli (after corrections of adhesion) is caused by the shift in the glass transition temperature of PA6 owing to the hydrostatic stress imposed by the indenter. Further proof is given with two examples on hydrostatic pressure‐dependent polymers: polytetrafluoroethylene and polycarbonate. Copyright © 2011 Society of Chemical Industry     

Micromechanical properties on the surface of PVC/SBR blends spatially resolved by a nanoindentation technique

The microhardness and micromodulus on the surface of poly(vinyl chloride) (PVC)/styrene‐butadiene rubber (SBR) blends were determined using a nanoindenter. A flat surface was obtained by microtoming the sample at ?100°C in liquid nitrogen. Dozens of indents along a line with a spatial interval of 0.5 μm were performed. From the loading and unloading curves of each indentation, the stiffnesses of the unloading curve and the contact area between the sample and the indenter were evaluated, and the local modulus and hardness were calculated. Profiles of the local hardness and modulus were obtained from the lines of indents. Pure PVC and a miscible PVC/acrylonitrile‐butadiene rubber (NBR) (40/10) blend showed constant modulus and hardness values. In the case of an immiscible PVC/SBR (50/50) blend, which has a morphology of elongated PVC droplets in the SBR matrix, the hardness and modulus profiles showed regions of the different phases. At the interface between the SBR and PVC phases, a step change in the modulus and hardness profiles was observed. The force required to deform the material at the same displacement increased systematically across the interface from the SBR to the PVC phase because of the increasing contribution of the PVC phase. Polym. Eng. Sci. 44:609–614, 2004. © 2004 Society of Plastics Engineers.     

Manufacture of Multilayered Artificial Cell Membranes through Sequential Bilayer Deposition on Emulsion Templates

Efforts to manufacture artificial cells that replicate the architectures, processes and behaviours of biological cells are rapidly increasing. Perhaps the most commonly reconstructed cellular structure is the membrane, through the use of unilamellar vesicles as models. However, many cellular membranes, including bacterial double membranes, nuclear envelopes, and organelle membranes, are multilamellar. Due to a lack of technologies available for their controlled construction, multilayered membranes are not part of the repertoire of cell-mimetic motifs used in bottom-up synthetic biology. To address this, we developed emulsion-based technologies that allow cell-sized multilayered vesicles to be produced layer-by-layer, with compositional control over each layer, thus enabling studies that would otherwise remain inaccessible. We discovered that bending rigidities scale with the number of layers and demonstrate inter-bilayer registration between coexisting liquid–liquid domains. These technologies will contribute to the exploitation of multilayered membrane structures, paving the way for incorporating protein complexes that span multiple bilayers.     

Efficacy of Trust-Building Tactics in Construction Mediation

Distrust hinders disputing parties and mediators from achieving mediation success. Mediators therefore often use different trust-building tactics to generate some degree of trust in themselves and in the mediation process. This paper reports a study that identified the trust-building tactics used by construction mediators and examined the efficacy of these tactics with respect to their outcomes. Three study stages were designed. With reference to the mediation model of Sloan (1998), trust-building tactics and outcomes were first identified in Stage I. Next, the data were collected from accredited mediators with a questionnaire survey in Stage II. The collected data were then validated via reliability assessments in Stage III. With the use of multiple regression analyses, the efficacy of the trust-building tactics was examined by relating these tactics to their outcomes. The findings of this study suggest that the trust-building tactics used in Step 4 (i.e., explore interests) of Sloan’s (1998) mediation model are influential in developing trust among disputing parties and that they can also act as a time-saving tool in the mediation process. Furthermore, it was found that mediators can earn trust by adopting the trust-building tactics used in Step 3 (i.e., issues and trust) of Sloan’s (1998) model. These tactics can also serve to improve the relationships between the disputing parties. The results show that the trust-building tactics used in the final step (i.e., solutions) of Sloan’s (1998) model seem to have low efficacy in developing trust among disputing parties.     

Design and implementation of contractual based real-time scheduler for multimedia streaming proxy server

In nowadays World Wide Web topology, it is not difficult to find the presence of proxy servers. They reduce network traffic through the cut down of repetitive information. However, traditional proxy server does not support multimedia streaming. One of the reasons is that general scheduling strategy adopted by most of the traditional proxy servers does not provide real-time support to multimedia services. Based on the concept of contractual scheduling, we have developed a proxy server that supports real-time multimedia applications. Moreover, we developed the group scheduling mechanism to enable processing power transfer between tasks that can hardly be achieved by traditional schedulers. They result in a substantially improved performance particularly when both time-constrained and non-time-constrained processes coexist within the proxy server. In this paper, the design and implementation of this proxy server and the proposed scheduler are detailed. Wai-Kong Cheuk received the B.Eng. (Hons.) and M. Phil. degrees in 1996 and 2001, respectively, from the Hong Kong Polytechnic University, where he is currently pursuing the Ph.D. degree. His main research interests include distributed operating systems and video streaming. Tai-Chiu Hsung (M'93) received the B.Eng. (Hons.) and Ph.D. degrees in electronic and information engineering in 1993 and 1998, respectively, from the Hong Kong Polytechnic University, Hong Kong. In 1999, he joined the Hong Kong Polytechnic University as a Research Fellow. His research interests include wavelet theory and applications, tomography, and fast algorithms. Dr. Hsung is also a member of IEE. Daniel Pak-Kong Lun (M'91) received his B.Sc. (Hons.) degree from the University of Essex, Essex, U.K., and the Ph.D. degree from the Hong Kong Polytechnic University, Hung Hom, Hong Kong, in 1988 and 1991, respectively. He is currently an Associate Professor and the Associate Head of the Department of Electronic and Information Engineering, the Hong Kong Polytechnic University. His research interests include digital signal processing, wavelets, multimedia technology, and Internet technology. Dr. Lun was the Secretary, Treasurer, Vice-Chairman, and Chairman of the IEEE Hong Kong Chapter of Signal Processing in 1994, 1995–1996, 1997–1998, 1999–2000, respectively. He was the Finance Chair of 2003 IEEE International Conference on Acoustics, Speech and Signal Processing, held in Hong Kong, in April 2003. He is a Chartered Engineer and a Corporate member of the IEE.