Flow distribution in spiral mandrel dies

An analysis of flow of a power law fluid in a spiral mandrel die is presented. The analysis is applied to study the effect of various die design parameters on the flow distribution at the end of the spiral mandrel section. Three variables that have a very strong effect on the flow distribution are the number of grooves, the initial clearance, and the groove helix angle. The distribution is improved by increasing the number of grooves, by using a non-zero initial clearance, and a relatively small helix angle. Two more variables that have a significant effect on the flow distribution are the taper angle and the initial groove depth. The optimum taper angle was found to be between 1 and 3 degrees. The distribution uniformity improves with the initial groove depth, while the pressure drop reduces at the same time.     

High-Strength Zirconia Fibers

Fine-grained polycrystalline zirconia fibers have been formed from an acetate precursor. The fibers contained a Y₂O₃ additive, which inhibited grain growth (grain size ≤0.5 μm) and allowed the tetragonal phase to be retained at room temperature. Fibers with diameters in the range 2 to 5 μm had strengths in the range 1.5 to 2.6 GPa.     

Development of a high‐resolution RGBW flexible display using a white organic light‐emitting diode with microcavity structure and that of a side‐roll touch panel

In this study, white organic electroluminescent devices with microcavity structures were developed. A flexible high‐resolution active‐matrix organic light‐emitting diode display with low power consumption using red, green, blue, and white sub‐pixels formed by a color‐filter method was fabricated. In addition, a side‐roll touch display was developed in combination with a capacitive flexible touch screen.     

Direct Measurement of Transformation Zone Strains in Toughened Zirconia

Residual strains responsible for crack tip shielding have been measured within transformation zones surrounding cracks in Mg-PSZ. Two techniques were used for strain measurement: moiré interferometry and high-resolution image matching. Both methods provide maps of differential in-plane displacements within the specimen surface intersected by the crack, the latter method with the higher resolution. The results are compared with finite-element analysis to assess surface relaxation effects, and the measured strains are used to evaluate the crack tip shielding stress intensity factor. Calculations based on the assumption that the unconstrained transformation strain is hydrostatic dilatation yielded results that were significantly smaller than the measured toughness increases.     

DYNAMIC TENSIONS IN FINITE OIL DROPLETS

In reacting systems, dynamic interfacial tension (IFT) values above 10-20 mN/m are often encountered. For such high tension values, infinitely long oil droplets will not be realised in spinning drop tensiometry. Hence, Vonnegut's solution will not be strictly valid. The experimentalist is then compelled to use one of the several alternative solution schemes proposed in the literature. We have obtained dynamic IFT data for 0.3125 mM oleic acid in hexadecane contacted with various NaOH solutions by the use of a novel experimental scheme called photo-micropendography. These tension values were then compared with spinning drop tensiometer data calculated by using three alternative solution schemes, namely, Vonnegut's method, the formula of Slattery and Chen and the analysis of Princen el al. The comparison showed that when the droplet's length/width ratio was below 2.5, Vonnegut's formula was severely in error. The solution scheme proposed by Slattery and Chen gave tension values close to those found by photo-micropendography over the entire range of IFT values exhibited by the oleic acid/caustic systems. However, the most consistent and reasonably accurate tension values resulted from the use of Table I in the paper by Princen, Zia and Mason. A simplified computer algorithm has been proposed for calculating dynamic interfacial tensions using the formulas and tables proposed by the latter authors. However, at length/width ratios above 2.5, the agreement between interfacial tensions determined by micropendography and spinning drop data calculated by the use of Vonnegut's solution was quite good.     

Subsoil <Superscript>15</Superscript>N-N<Subscript>2</Subscript>O Concentrations in a Sandy Soil Profile After Application of <Superscript>15</Superscript>N-fertilizer

Studies on emissions of nitrous oxide (N₂O) from agricultural soils mostly focus on fluxes between the soil and the atmosphere or are limited to the atmosphere in the topsoil. However, in soils with shallow water tables, significant N₂O formation may occur closer to the groundwater. The aims of this study were (i) to determine the importance of subsoil N₂O formation in a sandy soil; and (ii) to obtain a quantitative insight in the contribution of subsoil N₂O to the overall losses of N₂O to the environment. We applied ¹⁵N labeled fertilizer at a rate of 5.22 kg ¹⁵N ha⁻¹; 50% as Ca(NO₃)₂ and 50% as NH₄Cl, on a mesic typic Haplaquod seeded with potatoes (Solanum tuberosum L.), and traced soil N₂O concentrations and fluxes over a one-year period. Throughout the year, total N₂O and the amount of ¹⁵N recovered in soil N₂O were highest in the subsoil, with a maximum concentration at 48 cm depth in mid-February of 19900 μl m⁻³ and 24 μg ¹⁵N m⁻³, respectively. The maximum concentration coincided with the highest water-filled pore space of 71%. The cumulative flux of N₂O was 446 g N₂O-N ha⁻¹, the recovery of ¹⁵N in this flux was 0.06%. During the summer, maximum fluxes followed high soil N₂O concentrations. During winter, no such relation was found. We concluded that the formation of N₂O was the highest in the subsoil, largely controlled by water-filled pore space rather than NO₃⁻ concentration or temperature. Although high subsoil N₂O concentrations did not lead to high surface fluxes of N₂O in the winter, artificial draining may lead to high indirect N₂O emissions through supersaturated drainage water.     

Assessing the reliability of ordered categorical scales using kappa-type statistics

Methods for the analysis of reliability of ordered categorical scales are discussed, focussing on the limitation of the single summary-weighted kappa coefficients. A symmetric matrix of kappa-type coefficients is suggested as an alternative. The method is proposed as being suitable for ordinal scale where there is no underlying continuum. Their application is illustrated using two data sets from reliability studies. If, instead, distances between categories can be specified, a weighted mean of the matrix terms can be used as a summary measure. This is equal to a weighted kappa coefficient with squared weights, provided distances between adjacent categories are equal. When a study design corresponds to a one-way random effects model, estimates of precision of kappa-type coefficient, including the coefficients described here, can be obtained using the delta-method, bootstrap resampling by subjects or jack-knifing by subjects. In the case of interobserver reliability studies, where there may be systematic differences between observers, the investigator may wish to generalise to a population of observers and subjects. In this case, jack-knifing by observer and subject is suggested. Empirical comparisons are made between standard error estimates based on the delta-method, on jack-knifing by subjects and a two-way jack-knife by subjects and observers. The results suggest that standard errors based on the delta-method or jack-knifing by subject alone may be overly precise.     

The days ahead

How are government controls affecting healthcare foodservices?Are growing elderly & outpatient populations changing foodservices' missions. What are the hottest trends? As members of the American Society for Hospital Food Service Administrators prepared for their annual meeting in Orlando, FM queried 11 Southeastern directors to learn their most pressing concerns & how they are positioning their departments for the future.     

The determination of crack bridging forces

A method is presented for determining the bridging tractions acting on the fracture surfaces of cracks from measurements of the crack opening profile. The tractions may be expressed either as a function (x) of position in the crack or a function p(u) of the crack opening displacement. The feasibility of deducing (x) or p(u) from noisy displacement data is demonstrated by numerical simulations. It is found that the most complete information is contained in profiles of cracks growing from notches. Improved estimates of p(u) can also be found by analzying data from several cracks at different stress levels simultaneously.