羟基磷灰石/β-磷酸三钙/海藻酸钠复合多孔支架的制备与研究

本文讨论了羟基磷灰石/β-磷酸三钙/海藻酸钠(HAP/β-TCP/AG)多孔支架的制备,并通过电子显微镜观察了其微观结构、研究其干细胞亲和性和生物相容性。研究表明:该多孔支架具有三维连通网状结构,干细胞在支架上黏附、生长良好,具有良好的干细胞亲和性和生物相容性。     

The cholesterol-lowering effect of guar gum is not the result of a simple diversion of bile acids toward fecal excretion

The effects of partially hydrolyzed, nonviscous, guar gum (PHGG) on cholesterol metabolism and digestive balance have been compared with those of native guar gum (GUAR) in rats adapted to 0.4% cholesterol diets. Both types of guar gum elicited acidic fermentations in the large intestine, but only GUAR effectively lowered plasma cholesterol (P<0.001), chiefly in the triglyceride-rich lipoprotein fraction. The biliary bile acid excretion was significantly enhanced in rats fed GUAR (P<0.05), as well as the intestinal and cecal bile acid pool (P<0.001). In rats fed GUAR and to a lesser extent in those fed PHGG, the fecal excretion of bile acids and neutral sterol was higher than in controls (P<0.01). The digestive balance (cholesterol intake-steroid excretion) was positive in control rats (+47 μmol/d), whereas it was negative in rats fed GUAR (−20 μmol/d), which could involve a higher rate of endogenous cholesterol synthesis. In rats fed PHGG, the steroid balance remained slightly positive. Liver 3-hydroxy-3-methylglutaryl-CoA (HMG-CoA) reductase activity was very low (22 pmol/min/mg protein), owing to cholesterol supplementation, in control rats or in rats fed PHGG, whereas it was markedly higher (+463%) in rats fed GUAR. In conclusion, even if PHGG does alter some parameters of the enterohepatic cycle of cholesterol and bile acids, its effects are not sufficient to elicit a significant cholesterol-lowering effect. The intestinal (ileal or cecal) reabsorption of bile acids was not reduced, but rather increased, by GUAR; nevertheless the intestinal capacities of reabsorption were overwhelmed by the enlargement of the digestive pool of bile acids. In the present model, induction of HMG-CoA reductase probably takes place in the presence of elevated portal bile acid concentrations.     

Effect of La/K A-site Substitutions on the Ordering of Ba(Zn1/3Ta2/3)O3

The 1/3 <111>-type ordering of Ba(Zn_1/3Ta_2/3)O₃ (BZT) can be transformed to 1/2 <111>–type ordering by substituting the La³⁺ cation into the A site. The 1/3 <111> ordering in BZT is shown to be reduced, discontinued, and then replaced by 1/2 <111> ordering, using X–ray diffraction, electron microscopy, and Raman spectroscopy. On the other hand, potassium–substituted BZT only displays a reduction in the degree of ordering.     

Damage Development and Moduli Reductions in Nicalon—Calcium Aluminosilicate Composites under Static Fatigue and Cyclic Fatigue

Unidirectional and cross-ply Nicalon fiber-reinforced calcium aluminosilicate (CAS) glass-ceramic composite specimens were subjected to tension–tension cyclic fatigue and static fatigue loadings. Microcrack densities, longitudinal Young's modulus, and major Poisson's ratio were measured at regular intervals of load cycles and load time. The matrix crack (0° plies) density and transverse crack (90° plies) density increased gradually with fatigue cycles and load time. The crack growth is environmentally driven and depends on the maximum load and time. Young's modulus and Poisson's ratio decreased gradually with fatigue cycles and load time. The saturation crack densities under fatigue loadings were found to be comparable to those under monotonic loading. A matrix crack growth limit strain exists, below which matrix cracks do not grow significantly under fatigue loading. This limit coincides with the matrix crack initiation strain. Linear correlations between crack density and moduli reductions obtained from quasi-static data can predict the moduli reductions under cyclic loading, using experimentally measured crack densities. A logarithmic correlation can predict the Young's modulus reduction in a limited stress range. A fatigue crack growth model is proposed to explain the presence of two distinct regimes of crack growth and Young's modulus reduction.     

Controlled destruction of residual crosslinker in a silicone elastomer for drug delivery

In drug delivery systems that use silicone elastomers as a diffusion matrix for the active drug, it is common to crosslink the material by the hydrosilylation reaction. In this platinum‐catalyzed reaction, vinyl groups on a polymer add to the methyl siloxane hydride (MHS) groups on a low molecular mass crosslinker. With an excess of crosslinker, a fast curing is achieved and a fully crosslinked material is formed. Unreacted MHS groups were shown to remain in the elastomer after curing because of the excess crosslinker. In this work, a simple procedure was developed to eliminate the unreacted MHS groups from the final product. We found that storage of the product at +40°C and 75% relative humidity for a few weeks will effectively destroy the residual MHS groups in the elastomer. The effects of varying levels of humidity, oxygen, and temperature on this postcuring procedure were studied. The amount of MHS groups was measured with NMR and IR spectroscopy. We also found that the hardness of the material increased by approximately 25% as a consequence of this postcuring treatment. This increase is probably due to a secondary crosslinking reaction between MHS and silanol groups. Heat treatment at higher temperatures led to an even further increase in the hardness and compression modulus. Because no MHS groups remained in the elastomer when this heat treatment was started, it is apparent that another secondary crosslinking reaction is occurring, probably silanol condensation. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 2254–2264, 2002     

Plastic deformation of ZnO thin films through edge and screw dislocation movements

Columnar wurtzite grains were formed in sputtered ZnO thin films deposited on a plastic polyethylene terephthalate substrate. Selected-area diffraction patterns reveal that the columnar grains in the sputtered films present two preferred growth planes, namely, the basal (0002) and prismatic (100) growth planes. The diffraction patterns obtained also confirm that the microstructure of sputtered indium tin oxide thin films is amorphous in nature. Tensile tests indicate that the fracture strain of the ZnO thin film occurs between 1.73% and 2.14%, while the fracture strain of the indium tin oxide thin film occurs between 0.24% and 0.67%. Thus, the fracture toughness of the sputtered ZnO thin film is greater than that of the sputtered indium tin oxide thin film. High-resolution transmission electron microscopic images demonstrate that edge and screw dislocations could be identified in the sputtered ZnO thin films. Moreover, edge and screw dislocation movements may, respectively, be observed in the basal- and prismatic-oriented ZnO columnar grains of the sputtered ZnO thin films. Our results indicate that movements of the edge and screw dislocations in the basal- and prismatic-oriented ZnO columnar grains account for the plastic deformation of the investigated ZnO thin films under tensile stress.     

Influence of the preparation conditions on the properties of gold catalysts for the oxidation of glucose

In this work, two deposition–precipitation methods for the preparation of gold catalysts for glucose oxidation were investigated. Thus far, gold colloids immobilized on carbon have been used for catalytic glucose oxidation, but the long-term stability of these systems was not sufficient. To improve the long-term stability we used the deposition–precipitation methods using NaOH (DP NaOH) or urea (DP urea) as precipitation agents as they were described by Haruta and Dekkers, respectively, using alumina as a support material. With these methods, it was possible to prepare highly active and selective catalysts which showed an excellent long-term stability. DP urea was found to be the preferred method, because in contrast to DP NaOH, no losses of gold occurred during the preparation, and it was possible to adjust various gold contents up to 10 wt% Au.     

A new model for evaluating the electrical conductivity of nonferrous slag

Electrical conductivity of molten slag is an important physicochemical property for designing the refining process in electric smelting furnaces.Though conductivities of many slag systems have been measured,the quantitative relationships of conductivity with slag composition and temperature are still very limited.In this article,the Arrhenius law was used to describe the experimental data of conductivities for CaO-MgO-Al2O3-SiO2,CaO-Al2O3-SiO2,CaO-MnO-Al2O3-SiO2,as well as CaO-MgO-MnO-Al2O3-SiO2 systems,and...     

Cation interdiffusion between thick film of YBa2Cu3O7-δ and ceramic substrate

Thick films of superconducting oxides, YBa₂Cu₃O_7-, were successfully made by conventional screen-printing technology on Al₂O₃, MgO, and ZrO₂ substrates. Interdiffusion between the superconductive film and substrate was investigated using analytical electron microscopy. The results indicate that MgO and ZrO₂ are superior to Al₂O₃ for substrate materials.