Mechanistic investigation and selectivity of the grafting onto C60 of macroradicals prepared by cobalt-mediated radical polymerization

The grafting mechanism of poly(vinyl acetate) macroradicals prepared by cobalt-mediated radical polymerization onto C₆₀ is investigated. The experimental conditions directly impact the nature and stability of the PVAc/C₆₀ adducts. In the presence of residual initiating radicals that can compete with PVAc° macroradicals for addition onto C₆₀, mixtures of PVAc/C₆₀ adducts having between one and eight polymer chains per C₆₀ are formed. PVAc/C₆₀ adducts prepared with low [PVAc]:[C₆₀] ratios may contain weak C₆₀–C₆₀ bonds that further dissociate and account for the instability of the products. The formation of such dimers can be lessened by increasing the temperature from 30 °C to 100 °C. The temperature increase also allows a complete dissociation of the PVAc-Co dormant species into PVAc° macroradicals and an almost quantitative grafting of eight PVAc chains onto C₆₀, leading to well-defined C₆₀(PVAc)₈ octa-adducts. These results might shed new light on the grafting onto C₆₀ of macroradicals prepared by other CRP techniques.     

PLLA/Flax Mat/Balsa Bio-Sandwich—Environmental Impact and Simplified Life Cycle Analysis

In the present paper the environmental impact of biocomposites and bio-sandwich materials production are evaluated, using simplified Life Cycle Analysis (LCA) following the procedure recommended in the ISO 14044 standard. The materials are dimensioned and evaluated by comparing with reference materials, glass mat reinforced unsatured polyester and glass mat/unsatured polyester/balsa sandwich. The results indicate that bio-sandwich materials are very attractive in terms environmental impact. However further improvements in biocomposite and bio-sandwich mechanical strength are necessary if they are to be used in transport application compared to glass/polyester and glass/polyester/balsa sandwich.     

A priori checking inconsistencies among strategic constraints for assembly plan generation

This paper is related to the field of assembly plan generation. It describes a new approach to a priori check the consistency of an assembly strategy that is given by the assembly system designers before running an assembly plan generation algorithm. The aim of this work is to improve the assembly plan designer’s efficiency by reducing the research space while proving the existence of acceptable solutions. The assembly strategy combined with the product’s model implies a set of constraints on the assembly processes. The proposed method determines whether the given assembly strategy produces possible assembly processes. In case of inconsistencies among the strategic constraints, the method will help the designer to identify the contradictory constraints. The set of constraints can be expressed by a Boolean equation. First we present the key concepts and models related to the product, processes, and added values in the field of assembly plan generation. Second we define existing strategic constraints, and propose three new ones and a classification of strategic assembly constraints. The originality of the proposed method consists in defining an elementary strategic constraint that is used to describe every other constraint. The proposed method leads to model an assembly strategy by a single Boolean equation that is used to check the inconsistencies. An industrial case study is provided to highlight and to demonstrate the interests of this approach.     

Drag Power Loss Investigation in Cylindrical Roller Bearings Using CFD Approach

In high-speed rolling element bearings, the drag forces can be prominent and it is demonstrated in this investigation that the classical models may not be appropriate for correctly estimating this power loss contribution. A modification of the models is thus proposed, including the usual drag forces formulation relying upon the drag coefficient to be evaluated from a numerical computational fluid dynamics (CFD) approach. A three-dimensional approach that considers both the rings and the cylinder ends seems the only adequate approach to be used because a two-dimensional approach predicts a drag coefficient value that is too low. When using the former computed drag coefficient for the evaluation of the total power losses, high values of oil volume fraction must be employed to recover the measured power losses.     

Modeling planar slider-crank mechanisms with clearance joints in RecurDyn

Revolute joints in applications always show clearance between pin and bushing due to manufacturing tolerances, the need of relative motion or progressing wear. Many researchers developed and investigated methodologies to calculate the dynamic behavior of mechanisms with such imperfect joints. Very often they use a simple slider-crank mechanism to test or demonstrate the capability of their approaches. In this paper, a methodology for simulating a slider-crank mechanism with an imperfect revolute joint in RecurDyn, a commercial multibody simulation tool, is presented. Therefore, a thorough investigation of existing contact, damping and friction force models as well as different ways of modeling revolute joints in RecurDyn was conducted. For the investigation of the damping models, a special program for calculating the model parameters for a given coefficient of restitution was developed. Only one damping model was capable of reproducing the experimental results, which were found in literature. Some characteristic results of the slider-crank mechanism are presented in a way that they can be compared to results in other papers. Thereby. a good correlation was achieved, demonstrating the capabilities of the methodology.     

Crack initiation,propagation, and arrest in sintering powder aggregates

Cracking during sintering is a common problem in powder processing and is usually caused by constraint that prevents the sintering material from shrinking in one or more directions. Different factors influence sintering-induced cracking, including temperature schedule, packing density, and specimen geometry. Here we use the discrete element method to directly observe the stress distribution and sinter-cracking behavior in edge notched panels sintered under a uniaxial restraint. This geometry allows an easy comparison with traditional fracture mechanics parameters, facilitating analysis of sinter-cracking behavior. We find that cracking caused by self-stress during sintering resembles the growth of creep cracks in fully dense materials. By deriving the constrained densification rate from the appropriate constitutive equations, we discover that linear shrinkage transverse to the loading axis is accelerated by a contribution from the effective Poisson's ratio of a sintering solid. Simulation of different notch geometries and initial relative densities reveals conditions that favor densification and minimize crack growth, alluding to design methods for avoiding cracking in actual sintering processes. We combine the far-field stress and crack length to compute the net section stress, finding that it characterizes the stress profile between the notches and correlates with the sinter-crack growth rate, demonstrating its potential to quantitatively describe sinter-cracking.     

Presentation of a mixed reality software with a HoloLens headset for a nutrition workshop

Multimedia Tools and Applications - Microsoft has recently released a mixed reality headset called HoloLens. This semi-transparent visor headset allows the user who wears it to view the projection...