Electroluminescent zinc sulphide devices produced by sol-gel processing

Zinc sulphide thin film electroluminescent devices doped with Mn or Tb have been produced on p-type Si substrates using a process in which doped zinc oxide films are deposited by a sol-gel drain coating method from a solution of zinc acetate containing a manganese or terbium dopant. The films are then converted to ZnS by heating them in an atmosphere containing hydrogen sulphide which replaces the oxygyn with sulphur. The composition, crystalline structure and optical properties of films have shown that complete conversion from the oxide to the sulphide takes place. The luminescent characteristics of the devices so produced have been measured as a function of the doping concentrations, film thickness, insulator thickness and driving voltage and frequency. It has been found that yellow or green luminescence can be obtained using Mn or Tb doping respectively.     

Accurate determination of magnetic field gradients from four pointvector measurements. I. Use of natural constraints on vector dataobtained from a single spinning spacecraft

Cluster introduces a new generation of spacecraft that will measure the spatial gradients of the magnetic field in the Earth's magnetosphere. As gradients require knowledge of differences, small errors resulting from an inadequate knowledge of the orientations, zero levels and the scale factors of the magnetometer sensors affect the calculation of field gradients disproportionately and must be removed with high accuracy. We show that twelve calibration parameters are required for each of the spacecraft (for a total of 48 for the four spacecraft) to correctly infer the measured magnetic fields at each of the spacecraft. By application of a Fourier transform technique, some of the parameters can be recovered. We show that errors in eight of the twelve calibration parameters generate coherent monochromatic signals at the first and the second harmonics of the spin frequency in the despun data. We relate the real and the imaginary parts of the monochromatic signals to the eight calibration parameters. We then present a least squares scheme that improves the eight calibration parameters by iteration until the power of the coherent signal superimposed above the broad-band background is minimized     

Transcutaneous measurement and spectrum analysis of heart wallvibrations

For the noninvasive diagnosis of heart disease based on the acoustic and elastic characteristics of the heart muscle, it is necessary to transcutaneously measure small vibration signals, including components with an amplitude of less than 100 μm, from various parts of the heart wall continuously for periods of more than several heartbeats in a wide frequency range up to 1 kHz. Such measurement, however, has not been realized by any ultrasonic diagnostic methods or systems to date. By introducing the constraint least-square approach, this paper proposes a new method for accurately tracking the movement of the heart wall based on both the phase and magnitude of the demodulated signal to determine the instantaneous position of the object so that the vibration velocity of the moving object can be accurately estimated. By this method, small vibrations of the heart wall with small amplitudes less than 100 μm on the motion resulting from a heartbeat with large amplitude of 10 mm can be successfully detected with sufficient reproducibility in the frequency range up to several hundred Hertz continuously for periods of about 10 heartbeats. The resultant small vibration is analyzed not only in the time domain, but also in the frequency domain. As confirmed by the preliminary experiments herein reported, the new method offers potential for research in acoustical diagnosis of heart disease     

Effect of beam voltage on the properties of aluminium nitride prepared by ion beam assisted deposition

The effects of nitrogen-beam voltage on the structure, stress, energy band gap and hardness of AIN thin films deposited on Si (111), Si (100) and sapphire (0001) by ion beam assisted deposition (IBAD) are reported. As the nitrogen-beam voltage was increased from 50 to 200 V, the stress and disorder in the AIN films increased as determined by X-ray diffraction, FTIR and Raman spectroscopy. The preferred orientation of the film's c-axis changed from completely normal to the film at 100 V, to a mixture of normal and in the plane of the film at 200 V. For AIN films deposited under the same conditions, the films were more highly oriented on sapphire (0001) than in Si (111). The hardness of the films increased from 18.2 to 23.7 GPa with the nitrogen-beam voltage, and possible reasons for this change in hardness are considered.     

Some factors affecting the electrical properties of carbon-black-loaded butyl rubber during vulcanization

Butyl rubber mixtures loaded with 70 phr general purpose furnace black (GPF) and tetramethyl thiuram disulphide (TMTD)/S as vulcanizing system were prepared. The kinetics of their electrical conductivity development during the vulcanization process were followed by using an especially devised system. It was found that the increase in the electrical conductivity during vulcanization obeys an exponential growth function with time constant τ, which markedly decreases with increasing vulcanization temperature as well as with the efficiency of the vulcanizing system. After completion of the vulcanization process, about 80 min, the samples obtained possess reasonable stability and reproducibility of electrical conductivity.     

Continuously distributed phase shifts in chirped DFB lasers usingbent waveguides

The authors have implemented chirped distributed feedback (DFB) grating lasers with phase shifts [λ/8, 2λ/8 and 3λ/8] distributed continuously over various axial distances, using their recently proposed method for producing bent optical waveguides. The singlemode stability of the lasers with distributed phase shifts was found to be considerably higher than for lasers with abrupt phase shifts     

Mechanism of the early stages of α1 plate formation in a Cu-39 Pct Zn alloy

The early stages in the formation of α₁ plates in the ordered β′ matrix of a Cu-39 pct Zn alloy have been studied with transmission electron microscopy (TEM). The early stage plates were found to be free of stacking faults. Their contrast features are indeed those normally expected from small coherent plates. Electron microdiffraction confirms that these plates have the 9R structure characteristic of α₁ with the same lattice parameters and orientation relationships reported by previous investigators at much later stages of growth. Similarly, the 9R structure was disordered, even though it was formed in an ordered matrix, again repeating previous results obtained at a later stage of growth. These results further support the view that the α₁ Cu-Zn plates form by a diffusion-controlled mechanism. This article is based on a presentation made at the Pacific Rim Conference on the “Roles of Shear and Diffusion in the Formation of Plate-Shaped Transformation Products,” held December 18-22, 1992, in Kona, Hawaii, under the auspices of ASM INTERNATIONAL’S Phase Transformations Committee.     

Our new fragile world doesn't consist of developed and developing countries only

Health conditions have improved worldwide; therefore, the division into developed and developing countries no longer holds true. International organizations tend to divide countries into three groups. An increasing number of people are born in middle income countries where health conditions continue to improve. However, in a number of the least developed countries, mortality is on the rise in a spiral of economic stagnation, environmental problems, social misery, and ethnic/civil conflicts. This requires the medical assistance of international agencies from abroad. Since the 1960s there has been a drastic decline of child mortality in developing countries, especially in Asia. 1 billion people live in countries with child mortality under 20/1000, almost 3 billion live in countries with child mortality ranging 20-100/1000, and over 1 billion live in the least developed countries with child mortality over 100/1000. Unicef divides countries into developed, developing, and least developed countries, while the World Bank groups them as high-, medium-, and low-income countries. Thailand's child mortality is the same as that of Russia, while Cuba has a lower rate than Washington, D.C. On the other hand, Singapore is a developed high-income country with one of the world's healthiest populations. Stagnation and conflicts in the former socialist countries mean that many Asian and Latin American countries have better health status than some parts of Europe. Despite Africa's high mortality, its population growth is the highest in the world: in 20 years its population has doubled. Economic stagnation and the debt burden in many of these countries has resulted in ethnic conflicts and the collapse of social institutions: Somalia, southern Sudan, Rwanda, Liberia, Angola, perhaps Zaire, and Mozambique. The organization Physicians Beyond Borders is an example of extending humanitarian help and combatting social collapse in the least developed countries.