HDPE/LLDPE reactor blends with bimodal microstructures—Part II: rheological properties

Reactor blends of polyethylene/poly(ethylene-co-1-octene) resins with bimodal molecular weight and bimodal short chain branching distributions were synthesized in a two-step polymerization process. The compositions of these blends range from low molecular weight (LMW) homopolymer to high molecular weight (HMW) copolymer and vice versa HMW homopolymer to LMW copolymer. The shear flow characteristics of these polymers in the typical processing range mostly depend on the molecular weight and MWD of the polymer and are independent of the short chain branch content. From oscillatory shear measurements, it was observed that the viscosity of HMW polymers was reduced with the addition of LMW material. For the polymers produced with this two-step polymerization process, the LMW homopolymer and HMW copolymer blends and HMW homopolymer and LMW copolymer blends were melt miscible, despite the large viscosity differences of the pure components.     

A Fourier-transform infrared study of CO2 and CO2/H2 interactions with caesium-doped copper catalysts

FTIR spectra are reported of CO₂ and CO₂/H₂ on a silica-supported caesium-doped copper catalyst. Adsorption of CO₂ on a “caesium”/silica surface resulted in the formation of CO₂ ⁻ and complexed CO species. Exposure of CO₂ to a caesium-doped reduced copper catalyst produced not only these species but also two forms of adsorbed carboxylate giving bands at 1550, 1510, 1365 and 1345 cm⁻¹. Reaction of carboxylate species with hydrogen at 388 K gave formate species on copper and caesium oxide in addition to methoxy groups associated with caesium oxide. Methoxy species were not detected on undoped copper catalyst suggesting that caesium may be a promoter for the methanol synthesis reaction. Methanol decomposition on a caesium-doped copper catalyst produced a small number of formate species on copper and caesium oxide. Methoxy groups on caesium oxide decomposed to CO and H₂, and subsequent reaction between CO and adsorbed oxygen resulted in carboxylate formation. Methoxy species located at interfacial sites appeared to exhibit unusual adsorption properties.     

Cessation of polyunsaturated fatty acid formation in four selected filamentous fungi when grown on plant oils

Four fungi,Conidiobolus nanodes, Entomophthora exitalis, Mortierella isabellina, andMucor circinelloides, were grown on various oils (triolein, sesame, safflower, linseed, and oil fromM. isabellina) and produced lipids in which the fatty acids were predominantly the same as those of the original staring substrate. Only in the first two cases was there evidence of a small amount of chain elongation and of fatty acid desaturation taking place. The extent of this was only about 10% of that seen in glucose-grown cells. The apparent repression of the fatty acid desaturases and elongases was not reversed by growing cells on glucose and oils as mixed substrates—the fatty acid profiles were the same as when the fungi had grown in oils alone. Neither was the cessation of polyunsaturated fatty acid synthesis due to the presence of nonoil components (NOC) in the oil. Only the NOC from sesame oil affected one single conversion, that of 20∶3n-3 to 20∶4n–6. We conclude that fatty acid desaturase and elongase systems are repressed either partially or completely in a filamentous fungi grown on triacylglycerol oils.     

The effects of Cl-induced alloying in Pt–Sn/Al2O3 catalysts on butane/H2 reactions

The effects of oxidation/reduction regeneration treatments, with and without 1,2-dichloropropane present as a chlorinating agent, on the structure of Pt(3%)–Sn(4.5%)/Al₂O₃ catalysts have been correlated with selectivities for butane/H₂ reactions. Particles of Pt⁰ fin Cl-free catalysts were partly covered by Sn⁰, but retained exposed ensembles of Pt atoms which were active for isomerisation, hydrogenolysis and dehydrogenation reactions, the latter becoming dominant at high reaction temperatures. Coking reduced Pt ensemble size and, hence, also favoured high selectivities for dehydrogenation as hydrogenolysis and isomerisation sites became poisoned. In contrast, the addition of 1,2-dichloropropane in an oxychlorination step before reduction promoted 1:1 Pt⁰–Sn⁰ alloy formation after reduction, the proportion of the total Pt in alloy being enhanced by increasing 1,2-dichloropropane concentration and oxychlorination temperature. The alloy surfaces were inactive for isomerisation and hydrogenolysis reactions, giving dehydrogenation as the sole catalytic reaction.     

Enthalpies of pyrolysis and oxidation of Athabasca oil sands

Thermal degradation of Athabasca oil sands, bitumen, and its fractions have been investigated in N₂and in air, at 25–600 °C and at pressures up to 6.9 MPa, using thermogravimetry (TG) and high pressure differential scanning calorimetry (PDSC). These conditions are likely to occur during in-situ recovery of bitumen by underground combustion processes. Two regions of weight loss are detected using both gases. The endothermic low temperature volatilization reactions (150–400 °C) absorbed +26 mJ mg^?1 for oil sand to +2319 mJ mg^?1 for medium oil. The heats of reaction for high-temperature cracking and volatilization reactions (400–550 °C) were similar. The heats of reaction for the low-temperature oxidation reactions (150–375 °C) were ?405 mJ mg^?1 for oil sand to ?30200mJ mg^?1 for medium oil. Values for the high-temperature oxidation reactions (400–550 °C) were slightly higher. Increasing the pressure of nitrogen and air caused an increase in the endothermicity and exothermicity of the respective reactions.     

Molecular mass calibration in size-exclusion chromatography of coal derivatives

A number of procedures have been investigated for the calibration of a size-exclusion chromatography (s.e.c.) column in the determination of molecular mass (MM) distributions of coal derivatives. The behaviour of narrow fractions of coal extracts in the MM range 200–3000 was compared with a variety of the more generally available calibration standards. Calibration with preparative s.e.c. subfractions of materials similar to those under study has been recommended. Polystyrene standards are satisfactory, however, for MM < 1000, but above this range other polymer standards should be sought. Universal and molar volume calibration do not apply to coal-derived materials.     

Evaluation of the aromatic structure of coal tar pitch by solid and solution state n.m.r.

Rapid magic angle spinning has been used to obtain sideband-free high field ¹³C n.m.r. spectra of coal tar pitches in the solid state. However, the unfavourable cross-polarization and ¹H relaxation characteristics make it difficult to accurately estimate concentrations of quaternary aromatic carbon using the dipolar dephasing method. The concentrations of bridgehead aromatic carbon in the whole pitch and toluene-insoluble fraction investigated were deduced using a combination of solid and solution state n.m.r. and elemental analyses.     

SkaSim – Skalierbare HPC‐Software für molekulare Simulationen in der chemischen Industrie

This article outlines advances in molecular modeling and simulation using massively parallel high‐performance computers (HPC). In the SkaSim project, partners from the HPC community collaborated with users from science and industry. The aim was to optimize the prediction of thermodynamic property data in terms of efficiency, quality and reliability using HPC methods. In this context, various topics were dealt with: atomistic simulation of homogeneous gas bubble formation, surface tension of classical fluids and ionic liquids, multicriteria optimization of molecular models, the development of the molecular simulation codes ls1 mardyn and ms2, atomistic simulation of gas separation processes, molecular membrane structure generators, transport resistors and the evaluation of predictive property data models based on specific mixture types.     

Mobility of trace elements from selected Australian fly ashes and its potential impact on aquatic ecosystems

Batch leaching tests have been performed on fly ashes collected from four Australian power stations fuelled by chemically different coals. Two acidic and two alkaline fly ashes were subjected to long-term (144 h) leaching tests, and the behaviour of As, B, Mo and Se was investigated to obtain data on their potential for mobilisation during fly ash-water interactions. All four elements are mobile under different conditions and over different leaching times. The concentrations of these elements released in leaching solutions with initial pH values of 4, 7 and 10 were used to assess the influence of pH conditions on element mobility from the acidic and alkaline fly ashes. The most mobile of the four elements leached were Mo from alkaline fly ashes and B from acidic fly ashes. Arsenic concentration increased with time in leachate solutions from acidic and alkaline fly ashes; however, in solutions in contact with alkaline fly ashes the As concentration, after reaching a maximum, later decreased with time. Selenium mobility shows a similar pattern to that of As, with similar leaching concentrations. Boron has the highest relative mobility of all four elements. A process possibly responsible for the decrease in concentration of B, As and Se in alkaline leaching solutions is the formation of ettringite. Equilibrium between the solid phase (ash) and the leaching solution was not reached in any of the leaching experiments. The pH of the leaching solution is the key factor affecting the mobility of these trace elements in these fly ashes.