Dynamic modeling of the secondary drying stage of freeze drying reveals distinct desorption kinetics for bound water

In freeze drying, the desorption step for reaching a low target moisture content may take a significant fraction of the total process duration. Because the long-term stability of freeze-dried biological products strongly depends on the current moisture content, modeling the desorption process may help safely optimize the secondary drying step. Most published models assume a first-order desorption kinetic, but experimental evidence shows that strongly bound water in the monolayer takes a much longer time to be desorbed than less bound water in multilayer. The proposed model for desorption of freeze-dried lactic acid bacteria preparation accounts for monolayer and multilayer water state in the solid matrix, with very different desorption kinetics. Results showed that the ratio of characteristic desorption times (monolayer/multilayer) was almost 30. Temperature dependence was adequately described by an Arrhenius law in the range of 15 to 40°C. Model parameter identification used simultaneously gravimetric measurements with high time resolution and direct Karl-Fisher titration, from several experiments at different, time-varying temperatures.     

Thermal regimes of Li‐ion conductivity in β‐eucryptite

While it is well‐established that ionic conduction in lithium aluminosilicates proceeds via hopping of Li ions, the nature of the various hoping‐based mechanisms in different temperature regimes has not been fully elucidated. The difficulties associated with investigating the conduction have to do with the presence of grains and grain boundaries of different orientations in these usually polycrystalline materials. Herein, we use electrochemical impedance spectroscopy (EIS) to investigate the ion conduction mechanisms in β‐eucryptite, which is a prototypical lithium aluminosilicate. In the absence of significant structural transitions in grain boundaries, we find that there are three conduction regimes for the one‐dimensional ionic motion along the c axis channels in the grains, and determine the activation energies for each of these temperature regimes. Activation energies computed from molecular statics calculations of the potential energy landscape encountered by Li ions suggest that at temperatures below 440°C conduction proceeds via cooperative or correlated motion, in agreement with established literature. Between 440°C and 500°C, the activation barriers extracted from EIS measurements are large and consistent with those from atomistic calculations for uncorrelated Li ion hopping. Above 500°C the activation barriers decrease significantly, which indicates that after the transition to the Li‐disordered phase of β‐eucryptite, the Li ion motion largely regains the correlated character.     

Reactivity studies of 2,3,5,6-Tetra(2-pyridyl) pyrazine (tppz) with first-row transition metal ions

Reactions of 2,3,5,6-tetra(2-pyridyl) pyrazine (tppz) with [ML₆][X]₂ (L = CH₃CN, H₂O;X = [BF₄]⁻, [ClO₄]⁻, [NO₃]⁻ [BArF]⁻(BArF - B[3,5-C₆H₃(CF₃)₂]₄) lead to the high-yield formation of mononuclear [M(tppz)₂]²⁺, (M = Mn^II, Fe^II, Co^II, and Ni^II) and dinuclear [Ni₂(tppz)(CH₃CN)₆]⁴⁺ species. The new compounds were fully characterized by X-ray crystallographic, spectroscopic, and magnetic susceptibility measurements. Surprisingly, the 2:1 M:tppz reactions did not lead to isolation of the dinuclear species except in the case of Ni(II). It was further noted that even in the case of the Ni reactions, the nuclearity of the product depends on the choice of anions and the reaction conditions. Magnetic measurements of the mononuclear species [Co(tppz)₂]²⁺ revealed thermally induced spin-crossover behavior from a high-spin S = 3/2 at higher temperatures to a low-spin S = 1/2 complex at lower temperatures. The dinuclear compound [Ni₂(tppz)(CH₃CN)₆]⁴⁺ exhibits a weak anti-ferromagnetic interaction through the bridging tppz ligand.     

微波脱硫装置的设计EPDM再生胶的制备及性能研究

试制了微波脱硫罐并进行了EPDM再生胶的制备及性能研究,微波脱硫装置应包括搅拌、温控、密闭脱氧等装置;最佳脱硫功率为2kw,填充量为5kg;搅拌可以使得胶粉脱硫效果更均匀,最佳搅拌速度为60r/min;脱硫温度越高,脱硫效果越明显,最佳脱硫温度为270 ℃。     

Investigation of the properties of niobium pentoxide for use in dye-sensitized solar cells

This work demonstrates the obtention of Nb₂O₅ nanoparticles by the microwave-assisted hydrothermal synthesis method in a fast way and with the use of low temperatures. The heat treatment applied on the samples promotes the phase change in Nb₂O₅ from pseudohexagonal to orthorhombic as the temperature increases, with a particle size between 7.3 and 32.6 nm. The band gap of the samples decreases with increasing temperature, obtaining a minimum value of 3.04 eV at 800°C. Dye-sensitized solar cells (DSSC) were assembled using the Doctor Blade coating technique. The photovoltaic parameters of open-circuit voltage (Voc) and short-circuit current density (Jsc) were evaluated. The cells showed a photovoltaic response, demonstrating that Nb₂O₅ has a semiconductive potential. The DSSC have different characteristics regarding Jsc and Voc, showing that according to the temperature increase in the semiconductor sample, there is a decrease in the photovoltaic parameters of the cells.     

Simulating Microstructural Evolution and Electrical Transport in Ceramic Gas Sensors

An integrated computational approach to microstructural evolution and electrical transport in ceramic gas sensors has been proposed. First, the particle-flow model and the continuum-phase-field method are used to describe the microstructural development during the sintering of a prototype two-dimensional film. Then, the conductivity of the sintering samples is calculated concurrently as the microstructure evolves, using both resistor lattice models and effective medium theory for electrical transport in porous aggregates of lightly sintered particles. This approach, when combined with the modeling of resistivity at the grain–grain contacts as a function of neck geometry, ambient gas concentration and temperature, could facilitate the development and optimization of novel microstructures for advanced ceramic gas sensors.     

Structure-activity relationship study of 16 a-thiocamptothecins: an integrated in vitro and in silico approach

The instability of the hydroxylactone E ring represents a critical drawback of camptothecins, because the lactone ring is recognized to be essential for stabilization of topoisomerase I‐mediated DNA cleavage. In an attempt to investigate the effect of the thiopyridone pharmacophofore on the molecular and pharmacological features of the drug, we prepared a series of novel 16 a‐thiocamptothecin analogues. Due to the sulfur atom, a destabilization of the hydrogen bond between the hydroxy group in position 17 of the opened E ring and the carbonyl of the pyridone moiety is predicted, thus shifting the equilibrium toward the closed lactone form and increasing the lipophilic properties of the compounds. This feature was associated with superior antiproliferative potency, with reduced interaction with the human serum albumin and with substantial increase of the persistence of the topoisomerase I–DNA cleavable complex. These effects were prominent for thio‐SN38, the most active compound of the series. The favorable interactions at the molecular and cellular level of the reported thiocamptothecins confer promising features, and these compounds warrant preclinical development.     

Preparation for femur prosthesis of ceramic-metal combination artificial hip joint

1　ＩＮＴＲＯＤＵＣＴＩＯＮＴｈｅａｒｔｉｆｉｃｉａｌｈｉｐｊｏｉｎｔｆｅｍｕｒｓｕｓｅｄｉｎｃｌｉｎｉｃａｌａｔｐｒｅｓｅｎｔａｒｅｍａｄｅｏｆｍｅｔａｌａｎｄａｌｌｏｙ ,ｗｈｉｃｈｍａｉｎｌｙｉｎ ｃｌｕｄｅｓｔａｉｎｌｅｓｓｓｔｅｅｌ,Ｔｉａｌｌｏｙａ     

Preparation of CPB-modified FAU zeolite for the removal of tannery wastewater contaminants

The preparation of organomodified zeolites with different framework structures (FAU, LTA and MOR) using N-cetylpyridinium bromide (CPB) as tailoring agent was studied. The sorption properties of CPB-modified zeolites were evaluated in the removal of tannery contaminants from aqueous solution. The CPB-modified FAU-type zeolite presented the highest Cr(VI) retention capacity (37 mmol/kg) due to the higher Cr(VI) retention of its unmodified form (larger pore opening) and its high CPB sorption capacity. CPB-modified FAU zeolite also exhibited high thermal stability as consequence of special interactions between the CPB molecules and the zeolite surface. In addition, the intrinsic Cr(III) exchange capacity of FAU zeolite increased with CPB loading (162–527 mmol/kg), which appear to be due to an additional retention mechanism provided by the sorbed cetylpyridinium surfactant layer. On other hand, CPB-modified FAU zeolite also exhibited high toluene retention capacity (62 mmol/kg) due to of the hydrophobic character of its surfactant-modified surface and toluene adsorption on internal sorption sites of FAU zeolite. Thus, CPB-modified FAU zeolite appears as a promising adsorbent for simultaneous removal of Cr(III), Cr(VI) and toluene contaminants from aqueous solution.