Organic matter release in low temperature thermal treatment of biological sludge for reduction of excess sludge production.

Thermal treatment applied in association with a biological system allows for a significant reduction in excess sludge production (approximately 50%). In general, heat treatment is described as a sludge disintegration technique. This paper offers a thorough study on the impact of heat treatment, at temperatures below 100 degrees C, on the solubilisation of the sludge COD and its biodegradability. Discontinuous heating experiments were performed on activated and digested sludge. At all temperatures tested the released COD for digested sludge was systematically higher than that for activated sludge (15 and 40%, respectively, at 95 degrees C for 40 min of contact time). For the first 30 min, a 1st order kinetic, with respect to the residual COD, was systematically found. In the range of 40-95 degrees C, digested sludge had a lower activation energy than activated sludge (26 kcal/mol compared to 70-160 kcal/mol). COD solubilisation is thus more positively influenced by temperature in the case of activated sludge. This may be due to the significant difference in the ratio of protein/carbohydrate in digested and activated sludge (1-5 and 0.2-0.7, respectively). The increase in the COD/TKN ratio in the solubilised fraction after thermal treatment of activated sludge suggests a preferential solubilisation of proteins over carbohydrates. Respirometric tests performed on the solubilised COD showed that whatever the sludge origin, only 40-50% of released COD is biodegradable at a conventional hydraulic retention time (i.e., 24 h). Hence, heat treatment would act more through organic matter solubilisation rather than by a biodegradability increase.     

Effect of broaching on high-temperature fatigue behavior in notched specimens of INCONEL 718

Notches were machined in specimens of INCONEL 718 by a broaching process, where differing broaching runs led to differing extents of subsurface deformation and surface roughness. Fatigue tests were carried out at 600 °C with a trapezoidal loading waveform at 0.25 Hz. The broaching process that led to the more severe subsurface deformation (but lower surface roughness) showed the worst fatigue performance. Analysis of total strain amplitude in the notch root with the aid of an elastoplastic finite-element (FE) model showed that the work hardening related to the subsurface deformation caused by the different broaching can account for the difference in fatigue lives. Differences in initiation and growth behavior were seen for the two broached finishes as well as for broached and subsequently polished samples. These differences are discussed in terms of a change in crack growth initiation and growth mechanisms due to the presence of the work-hardened layer.     

Performance of simple response method for the establishment and adjustment of calibration intervals

Managing calibration intervals in order to fulfill requirements of quality-oriented organizations is discussed in this paper. In particular, the simple response method is considered. According to this technique, the interval between successive calibrations is adjusted adaptively on the basis of the outcome of the last calibration process. An original analysis is presented about the properties of such calibration interval handling methods. Finally, directions are given on how to tune its parameters optimally, in order to meet desired levels of long-term measurement reliability.     

Use of electrochemical oxidation process as post-treatment for the effluents of a UASB reactor treating cellulose pulp mill wastewater.

The main purpose of this study was to evaluate the performance of the electrochemical oxidation process as a post-treatment for the effluents of a bench-scale UASB reactor treating simulated wastewater from an unbleached pulp plant. The oxidation process was performed using a single compartment cell with two plates as electrodes. The anode was made of Ti/Ru0.3Ti0.7O2 and the cathode of stainless steel. The following variables were evaluated: current density (75, 150 and 225 mA cm(-2)) and recirculation flow rate in the electrochemical cell (0.22, 0.45 and 0.90 L h(-1)). The increase in current density from 75 to 225 mA cm(-2) did not increased the color removal efficiency for the tested flow rates, 0.22, 0.45 and 0.90 L h(-1), however the energy consumption increased significantly. The results indicated the technical feasibility of the electrochemical treatment as post-treatment for UASB reactors treating wastewaters from pulp and paper plants.     

Static and pulsed pressures measured using electrically conducting rubbers

A method of measuring static and pulsed pressures using electrically conducting rubber sensors is proposed. The method is based on a change in the volume resistivity of a filled rubber under the action of external pressure. The pressure-induced change in resistance of the rubber sensor is proportional to the applied pressure and can be measured by a bridge circuit. Using this method, it is possible to evaluate the degree of homogeneity of the pressure distribution over a solid surface. This is achieved by distributing rubber sensors over the given surface.     

An experiment for showing some kind of artificial understanding

In this paper we design an experiment which can be depicted as a simple scenario, a very limited 'world'. In this world, there are an actor that can pursue a project and an observer that is keeping its eyes on the actor. We try to show in the experiment that the observer can to some degree understand the actor based on its knowledge and some metaphors, i.e. understand what the actor is doing and why. As the conclusion of this experiment, we try to show some features of 'understanding'. These are (1) that 'understanding' has to be based on some preliminary knowledge; (2) that 'understanding' is a process of incremental learning; (3) that, as for symbolic systems, some metaphors are necessary for mapping real entities into concepts in mind.