Summary of discussion on ‘Sciences related to pitch and coke usage in carbon manufacture’

This article is a brief summary of the Discussion session held after the presentation of the preceding papers at the conference organized by the Industrial Carbon and Graphite Group of the Society of Chemical Industry, London, March 1984.     

Introduction of a nonlinearity measure for principal component models

Although principal component analysis (PCA) is an important tool in standard multivariate data analysis, little interest has been devoted to assessing whether the underlying relationship within a given variable set can be described by a linear PCA model or whether nonlinear PCA must be utilized. This paper addresses this deficiency by introducing a nonlinearity measure for principal component models. The measure is based on the following two principles: (i) the range of recorded process operation is divided into smaller regions; and (ii) accuracy bounds are determined for the sum of the discarded eigenvalues. If this sum is within the accuracy bounds for each region, the process is assumed to be linear and vice versa. This procedure is automated through the use of cross-validation. Finally, the paper shows the utility of the new nonlinearity measure using two simulation studies and with data from an industrial melter process.     

Linear demosaicing inspired by the human visual system.

There is an analogy between single-chip color cameras and the human visual system in that these two systems acquire only one limited wavelength sensitivity band per spatial location. We have exploited this analogy, defining a model that characterizes a one-color per spatial position image as a coding into luminance and chrominance of the corresponding three colors per spatial position image. Luminance is defined with full spatial resolution while chrominance contains subsampled opponent colors. Moreover, luminance and chrominance follow a particular arrangement in the Fourier domain, allowing for demosaicing by spatial frequency filtering. This model shows that visual artifacts after demosaicing are due to aliasing between luminance and chrominance and could be solved using a preprocessing filter. This approach also gives new insights for the representation of single-color per spatial location images and enables formal and controllable procedures to design demosaicing algorithms that perform well compared to concurrent approaches, as demonstrated by experiments.     

Semiempirical,squeeze flow,and intermolecular diffusion model. II. Model verification using laser microwelding

This article reviews the application of a coupled squeeze flow and intermolecular diffusion model, which was used to predict the quality and size of microwelds in plastics. Weld widths predictions were compared with previously presented experimental results using moving heat source models and temperature fields. The motivation for this work was to develop and verify a model based on fundamental principles that could accurately predict weld size and strength for conventional plastic welding techniques as well as novel techniques such as laser microwelding. It is envisioned that the resulting model could be used to predict proper welding parameters, including laser power and travel speed, to produce welds of varying size. Although insight into weld quality can be derived from this model, it was not the goal of this work to accurately predict weld strength for laser microwelding because of the difficulty in measuring weld strength on the micron scale. However, as reported in Part 1, weld strength for impulse welds were accurately predicted. In this model it was found that variable temperature histories, rather than a single value of maximum weld temperature, allows more accurate modeling of the welding process. In this work (Part 2), microwelds as small as 11 μm in width were produced with transmission infrared welding. In addition, welds over 150‐μm wide were also generated and the model was able to predict the range of weld widths that were found experimentally. It was found that the predictions were in very good agreement with the experimental results. There was some deviation between the experimental data and the model at the extreme parameters and it is believed that this was due to the temperature‐dependent material properties as well as optical aberrations. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers     

Modeling and sensitivity analysis of fire emissions in southern Africa during SAFARI 2000

This paper uses three recently generated southern African satellite burned area products for the month of September 2000 in a sensitivity study of regional biomass burning emissions for a number of trace gases and particulates. Differences in the extent and location of areas burned among products generated from Moderate Resolution Imaging Spectroradiometer (MODIS), Systeme Pour l'Observation de la Terre (SPOT-VEGETATION), and Along Track Scanning Radiometer (ATSR-2) data are significant and result in different emissions estimates for woodland and grassland land cover types. Due to the different emission profiles in woodlands and grasslands, favoring relatively more products of incomplete combustion in woodlands compared with products of complete combustion in grasslands in the late dry season, these changes are not proportional to the differences in the burned area amounts. The importance of accurate burned area information not just in terms of the total area but also in terms of its spatial distribution becomes apparent from our modeling results. This paper highlights the urgent need for satellite data producers to provide accuracy assessments associated with satellite-derived products. Preferably, these accuracy data will be spatially explicit, or defined in a way that can be applied in a spatially explicit modeling context, to enable emissions uncertainties to be defined with respect to different landscape units in support of greenhouse gas emissions reporting.