Review on testers for measuring flow properties of bulk solids

 The author was asked by the International Fine Particle Research Institue (IFPRI) to write a critical review on shear testers for IFPRI-members. The review was delivered to IFPRI in summer 1999. Following the contract with IFPRI it was not allowed to publish the review elsewhere for at least two years. Granular Matter invited the author to submit the review in the original form; during the refereeing process (besides other changes) it turned out that some remarks should be added here for clarification: - Since 1999, the author is not aware of a really new device for testing bulk solid properties, which could lead to a change of the general comments and conclusions provided in the review. It was argued, that the review is referring too much to the work of Jenike, while the works of Johanson and Peschl were not adequately cited. Both are excellent engineers with a lot of experience, but their basic ideas are not available in published form, and if, they are not set in relation to alternative approaches so that an objective comparison in detail would be a future research issue rather than a topic in this report. A discussion on the influence of electrostatic charges was missing. There hardly is an influence, since the particles are in continuous contact. Only with non-conducting plastic particles electrostatic charges could cause problems. But no relevant experiments and results are known. In closed systems, the effect of electric charges is thus mainly neglected, but it is clear that electrostatic forces are eminent in flows with a free surface – an issue not addressed in this review. Received: 1 November 2002     

Fundamental aspects of excitation and propagation of on-line partial discharge signals in three-phase medium voltage cable systems

On-line partial discharge (PD) detection of three-phase belted medium voltage cable connections results in a number of interpretation differences as compared to off-line measurements where only one phase is energized. The induced currents and charges in the phase conductors and earth screen upon a PD not only depend on the discharge site, but also become phase angle dependent. Furthermore, simulations show that the PD distribution itself varies with the amount of eccentricity of the rotating electric field and may differ from the off-line distributions obtained with a linear field. Finally, the PD propagation in a multi-conductor cable also alters the signals measured at the cable terminals. In this paper, induced charges and PD distributions are studied by means of computer simulation. The cable propagation characteristics are verified by measurements.     

Cross-Layer Packetization and Retransmission Strategies for Delay-Sensitive Wireless Multimedia Transmission

Existing wireless networks provide dynamically varying resources with only limited support for the quality of service required by the bandwidth-intense, loss-tolerant and delay-sensitive multimedia applications. This variability of resources does not significantly impact delay insensitive data transmission (e.g., file transfers), but has considerable consequences for multimedia applications. Recently, the research focus has been to adapt existing algorithms and protocols at the lower layers of the protocol stack to better support multimedia transmission applications and conversely, to modify application layer solutions to cope with the varying wireless networks resources. In this paper, we show that significant improvements in wireless multimedia performance can be obtained by deploying a joint application-layer adaptive packetization and prioritized scheduling and MAC-layer retransmission strategy. We deploy a state-of-the-art wavelet coder for the compression of the video data that enables on-the-fly adaptation to changing channel conditions and inherent prioritization of the video bitstream. We pose the cross-layer problem as a distortion minimization given delay constraints and derive analytical solutions by modifying existing joint source-channel coding theory aimed at fulfilling rate, rather than delay, constraints. We also propose real-time algorithms that explicitly consider the available information about previously transmitted packets. The obtained results show significant improvements in terms of video quality as opposed to ad-hoc optimizations currently deployed, while the complexity associated with performing this optimization in real time, i.e., at transmission time, is limited     

The stiffness matrix in elastically articulated rigid-body systems

Discussed in this paper is the Cartesian stiffness matrix, which recently has received special attention within the robotics research community. Stiffness is a fundamental concept in mechanics; its representation in mechanical systems whose potential energy is describable by a finite set of generalized coordinates takes the form of a square matrix that is known to be, moreover, symmetric and positive-definite or, at least, semi-definite. We attempt to elucidate in this paper the notion of “asymmetric stiffness matrices”. In doing so, we show that to qualify for a stiffness matrix, the matrix should be symmetric and either positive semi-definite or positive-definite. We derive the conditions under which a matrix mapping small-amplitude displacement screws into elastic wrenches fails to be symmetric. From the discussion, it should be apparent that the asymmetric matrix thus derived cannot be, properly speaking, a stiffness matrix. The concept is illustrated with an example.     

Integrated Smart Sensor Calibration

In many applications electronic sensors are used toimprove performance and reliability of measurement systems. Suchsensors should provide a correct transfer from the physical signalto be measured to the electrical output signal. One importantstep to achieve this, is to calibrate each sensor by applyingdifferent reference input signals and adjusting the sensor transferaccordingly. Besides expensive reference equipment the calibrationprocess takes much time and attention per individual sensor,which means a considerable increase in sensor production costs.By including at the sensor or sensor interface chip a programmablecalibration facility the calibration of such smart sensors caneasily be automated and can be executed for a batch of sensorsat a time, thus minimizing the calibration time and costs. Thispaper presents a calibration method and options for integrationin the smart sensor concept, in hardware as well as in software.An advantage of the proposed method is that it does not needa large matrix of calibration data, which needs to be storedin a look-up table or converted into a correction formula, butinstead it uses a step-by-step approach to correct the sensortransfer at each calibration measurement until the error is sufficientlysmall.     

Characterization and optimization of linearly tapered slot antenna pattern

A parametric study of linearly tapered slot antenna (LTSA) in air and a method for optimization of its pattern are presented. A method of moments code is utilized to investigate the behavior of LTSA’s as the length, height and the taper angle varies. It is shown that the antenna pattern can be improved using a top layer of dielectric material with varying permittivity.     

Generation of frequency-chirped optical pulses in a large-slippagefree-electron laser

We have investigated the optical output of the free-electron laser for infrared experiments (FELIX) when it is driven by an electron beam with a ramped energy. We show that the applied slow ramp on the electron beam energy leads to a frequency chirp on each picosecond optical pulse. Typical values for the chirp are 0.2% frequency sweep across a 1.5-ps-long optical pulse. The optical pulses were analyzed with a double-grating pair and with a second-order autocorrelator. The pulse duration was reduced in the double-grating pair by 20%. A linear dependence of the chirp on the cavity desynchronization was measured     

The Continuous Interpolating Self-organizing Map

The self-organizing map (SOM) [5] provides a general data approximation method which is suitable for several application domains. The topology preservation is an important feature in data-analysis and may also be advantageous for the evaluation of the data in a function approximation or regression task. For this reason the interpolated self-organizing map (I-SOM) adds an output layer to the SOM architecture which computes a real valued output vector. This paper presents an extension of I-SOM towards a continuous interpolation. It is compared to RBF and to the parametrized self-organizing map.     

Inhibiting and deactivating effects of water on the selective catalytic reduction of nitric oxide with ammonia over MnOx/Al2O3

The effect of water on the selective catalytic reduction (SCR) of nitric oxide with ammonia over alumina supported with 2–15 wt.-% manganese oxide was investigated in the temperature range 385–600 K, with the emphasis on the low side of this temperature window. Studies on the effect of 1–5 vol.-% water vapour on the SCR reaction rate and selectivity were combined with TPD experiments to reveal the influence of water on the adsorption of the single SCR reactants. It turned out that the activity decrease due to water addition can be divided into a reversible inhibition and an irreversible deactivation. Inhibition is caused by molecular adsorption of water. TPD studies showed that water can adsorb competitively with both ammonia and nitric oxide. Additional kinetic experiments revealed that adsorbed ammonia is present in excess on the catalyst surface, even in the presence of water. Reduced nitric oxide adsorption is responsible for the observed reversible decrease in the reaction rate; the fractional reaction order changes from 0.79 in the absence of water to 1.07 in its presence. Deactivation is probably due to the dissociative adsorption of water, resulting in the formation of additional surface hydroxyls. As the amount of surface hydroxyls formed is limited to a saturation level, the deactivating effect on the catalyst is limited too. The additional hydroxyls condense and desorb in the temperature range 525–775 K, resulting in a lower degree of deactivation at higher temperature. A high temperature treatment at 775 K results in a complete regeneration. The amount of surface hydroxyls formed per unit surface area decreases at increasing MnO_x-loading. The selectivity to the production of nitrogen is enhanced significantly by the presence of gas phase water.