Electrostatic model for an asymmetric combdrive

This paper presents an analytical solution to the electrostatic actuation of an asymmetric combdrive in out-of-plane and torsional motions. The exact solutions to force in the out-of-plane motion and the integral for torque in the torsional motion are obtained. The dependence of the peak force on the thickness of the movable fingers and the amount of overlap of the combs is given in closed form. Using our model, the shift of the natural resonant frequency due to a dc bias is analyzed. Furthermore, our solution also applies to the in-plane motion of an in-plane interdigitated combdrive. We found that an in-plane interdigitated combdrive generates a constant force within 0.1% when the minimum initial engagement length of the combs is twice the separation gap     

Plant algae method for arsenic removal from arsenic contaminated groundwater

Field studies were carried out in Urumqi River Basin in Northwest China. The study focused on experimentation on a plant algae method that was tested by taking various water chemistries into consideration. The results from a greenhouse experiment evaluated for four doses of P (0, 100, 200, and 300 μmol/L) using two ferns (30 and 60 day old) on 15 L of contaminated groundwater per plant revealed that the biomass of 30-day old ferns gained was higher than 60-day fern. As solution-P increased from 0 to 450 μmol/L, Phosphorus concentration in the fronds increased from 1.9 to 3.9 mg/kg and 1.95 to 4.0 mg/kg for 30-d and 60-d ferns respectively. This study showed that the plant algae method may be a good solution to maximize arsenic uptake in the short term under normal climatic conditions.     

A new procedure for determining specific filter cake resistance from filtration data

A new procedure has been developed for the determination of specific filter cake resistance from experimental filtration data. Unlike the conventional procedure which treats constant-pressure filtration data through the t/V vs. V plot and yields a single value of the average specific cake resistance (α_av) from a given experiment, this new procedure allows the establishment of the relationship of α_av vs. the cake compressive stress (p_s) over a range of p_s values. Results from the new procedures were compared with those obtained from the procedure based on the t/V vs. V plot as well as those from compression-permeability (C-P) measurements. Discussions on the possible improvement of the new procedure are also presented.     

Petri nets with causal time for system verification

We present a new approach to the modelling of time constrained systems. It is based on untimed high-level Petri nets using the concept of causal time. With this concept, the progression of time is modelled in the system by the occurrence of a distinguished event, tick, which serves as a reference to the rest of the system. In order to validate this approach as suitable for automated verification, a case study is provided and the results obtained using a model-checker on high-level Petri nets are compared with those obtained for timed automata using prominent tools. The comparison is encouraging and shows that the causal time approach is intuitive and modular. It also potentially allows for efficient verification.     

Flexible diamond-like carbon films on rubber: Friction and the effect of viscoelastic deformation of rubber substrates

This paper focuses on the frictional behavior of flexible diamond-like carbon (DLC) film-coated hydrogenated nitrile butadiene rubber. By making use of the substantial thermal mismatch between DLC film and rubber substrate, a dense network of cracks forms in the DLC films and contributes to flexibility. The influence of the size of DLC film microsegments on the frictional performance is studied. The effect of viscoelasticity of the rubber substrate on the frictional behavior of the DLC film-coated system is scrutinized by tribo-tests and theoretical analysis. The importance of adhesive and hysteresis contributions to friction is revealed, and an overarching model is presented.     

Bridging TiO2 nanoparticles using graphene for use in dye‐sensitized solar cells

The use of graphene to bridge TiO₂ particles in the photoanode of dye‐sensitized solar cell for reduced electrical resistance has been investigated. The difficulty in dispersing graphene in TiO₂ paste was overcome by first dispersing graphene oxide (GO) into the TiO₂ paste. The GO was then reduced to graphene after the sintering of TiO₂. This is shown through transmission electron microscopy and X‐ray photoelectron spectroscopy analysis. Cell performance was evaluated using a solar simulator, incident photon to electron conversion efficiency, intensity modulated photocurrent/photovoltage spectroscopy under blue light, and electrochemical impedance spectroscopy. Depending on the amount of graphene in the photoanode, the cell performance was enhanced to different degrees. A maximum increase of 11.4% in the cell efficiency has been obtained. In particular, the inclusion of graphene has reduced the electron diffusion time by as much as 23.4%, i.e. from 4.74 to 3.63 ms and increased the electron lifetime by as much as 42.3%, i.e. from 19.58 to 27.85 ms. Copyright © 2014 John Wiley & Sons, Ltd.     

Coupled nanowire-based hybrid plasmonic nanocavities on thin substrates

We theoretically analyze nanowire-based hybrid plasmonic nanocavities on thin substrates at visible wavelengths. In the presence of thin suspended substrates, the hybrid plasmonic modes, formed by the coupling between a metal nanowire and a dielectric nanowire with optical gain, exhibit negligible substrate-mediated characteristics and overlap better with the gain region. Consequently, the confinement factor of the guided hybrid modes is enhanced by more than 42%. However, the presence of significant mirror loss remains the main challenge to lasing. By adding silver coatings with a sufficient thickness range on the two end facets, we show that the reflectivity is substantially enhanced to above 50%. For a coating thickness of 50 nm and cavity length of about 4 μm, the quality factor is above 100.     

Cathodoluminescence and Field-Emission Properties of β-Ga2O3 Nanobelts

β-Ga₂O₃ nanobelts were synthesized using a vapor transport process in a controlled ambient. Structural characterization revealed that the as-synthesized samples consisted of monoclinic β-Ga₂O₃ nanobelts, and the presence of gallium-associated defects was verified using cathodoluminescence (CL). The formation of gallium-associated defects was explained by the insufficiency of the supply of cations, generating gallium vacancies on the (010) facet during growth. Furthermore, field-emission measurements indicated that β-Ga₂O₃ nanobelts exhibited defect-related electron emission. The turn-on fields of β-Ga₂O₃ nanobelts increased significantly with the degree of structural defects. For a sample prepared under 15% ambient oxygen, Fowler–Nordheim (F–N) analysis revealed two distinct field-enhancement factors of 1194 and 276, respectively. A correlation between field emission and structural defects was proposed. The experimental results demonstrate the presence of gallium-associated defects, which behave as electron traps, degrading the electron field-emission properties of β-Ga₂O₃ nanobelts.