Characteristics of tiger nut milk: effects of milling

A standard method for the extraction of tiger nut milk has been introduced. It has been shown that, although milling duration improves the yield of tiger nut milk solids and its nutrient composition, there is a quantifiable loss of nutrient in the pressing residue during milk extraction. Milling duration improved the colloidal stability of the milk against creaming during 16 h of storage. A higher milling intensity resulted in the aggregation of biological polymers which resulted in colloidal destabilisation. Milling improved the lightness and stability and reduced browning rate of the tiger nut milk during storage. This report is important for the production of tiger nut milk of consistent and comparable characteristics. Milling has been introduced as a processing method for the qualitative and quantitative modulation of the properties of tiger nut milk. It is recommended to develop further strategies to improve the colloidal stability of tiger nut milk as a beverage.     

Combination of nuclear magnetic resonance spectroscopy and nonlinear methods to analyze the copolymerization of phosphonic acid derivatives

We demonstrate in this study that the combination of modern inline monitoring methods [here: inline nuclear magnetic resonance (NMR)] with simulations gains more exact and profound kinetic results than previously used methods like linearization without that combination. The ¹H-NMR spectroscopic data (more than 100 data points) are used to construct the copolymerization diagram. The reactivity ratios are obtained applying the van Herks nonlinear least square method. The examination of the radical copolymerization of 2-hydroxyethyl methacrylate (HEMA) with (2-{[2-(ethoxycarbonyl)prop-2-en-1-yl]oxy}ethyl) phosphonic acid (ECPPA) as important adhesive monomer used in dentistry yields reactivity ratios of r_HEMA = 1.83; r_ECPPA = 0.42. The copolymerization diagram reflects nonideal, non-azeotropic copolymerization. The sequence distribution of the obtained by Monte Carlo simulation indicates the generation of statistical copolymers. As an important finding, it is demonstrated that the repeating units responsible for etching and adhesion are arranged over the whole polymer chain, which is necessary to achieve proper functionality. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 48256.     

ENHANCING THE CREATIVITY OF REENGINEERING Techniques for Making IS More Creative

Industries in the US continue to lose ground in international competition. If IS is to help change that trend, it will have to become more creative. Creativity improvement programs are being introduced in other areas of the company— now is the time for IS organizations to follow suit.     

A process model for active brazing of ceramics: Part II Optimization of brazing conditions and joint properties

In the present investigation, the process model developed in Part I has been applied to evaluate the microstructure and strength evolution during active brazing of ceramics. As a starting point, reaction-layer growth is assumed to occur isothermally with no restrictions in the supply of reactive element. Different kinds of diagrams are then constructed to show how specific process variables (e.g. the heating and cooling period, the limiting layer thickness, and the diffusion mechanism) affect the growth kinetics. It is concluded that the key to improved joint properties lies in control of the reaction-layer thickness through optimization of the brazing conditions, and an illustration of this is given. This revised version was published online in November 2006 with corrections to the Cover Date.     

An 8-bit, 200 MSPS Folding and Interpolating ADC

An 8-bit, 200 MSPS folding and interpolating analog-to-digitalconverter, ADC, has been implemented in a 1.2 µmBiCMOS-process. It achieves 7.5 effective bits with a power dissipationof 575mW. The active area is 4mm². The implementationand measured results are presented. A simple analytical modelfor the interpolation-induced nonlinearity in a folding and interpolatingADC using sinusoidal folding is presented. The bowing of thereference ladder due to interaction with the input stages isanalyzed, and analytical models are derived.     

Treatment of Humic Waters By Ozone

Two different generators for ozone were tested, a traditional electrical discharge generator and a generator based upon UV–irradiation of air at 150–180 nm. It was demonstrated that the traditional generator gave slightly higher reductions in levels of color for equivalent ozone dosages. Both gases affected the molecular weight distribution in the way that the bigger molecules were broken down to smaller ones. No significant difference between the molecular weight reduction efficiency of the gases was found.     

Activated dissociative chemisorption of methane on Ni(100): a direct mechanism under thermal conditions?

The dissociative chemisorption of methane on a Ni(100) single crystal has been studied under thermal conditions as a function of pressure and temperature. The initial sticking coefficient was measured in the pressure range of 0.010–7.0 mbar at temperatures ranging from 375 to 500 K. A strong pressure dependence was observed, consistent with a direct dissociation mechanism under these thermal conditions. This was further confirmed by experiments where the gas at a low pressure was heated by a thermal finger facing the crystal surface. With the thermal finger at the same temperature as the surface, it was possible to ensure that the methane was fully equilibrated to the crystal and an activation energy of 59±1.5 kJ/mol was determined under isothermal conditions.     

On the solubility of aluminum in cryolitic melts

The solubility of aluminum in NaF-AlF₃-Al₂O₃ melts with various additives was found to increase with increasing NaF/AlF₃ molar ratio (CR) and increasing temperature and to decrease with additions of A1₂O₃, CaF₂, MgF₂, and LiF to the melts. With the use of literature data for the activities of NaF and A1F₃ in cryolitic melts, three dissolution reaction models were found to give a good fit to the experimental solubility data. According to the most probable of these models the total concentration of dissolved aluminum (aluminum and sodium species) is given by c_Al = c_Na(diss) + c_AlF2- + c_Al2F3- + c_Al3F4- + c_Al4F5- In NaF rich melts, aluminum will dominantly dissolve as sodium, while at cryolite ratios commonly used in aluminum electrowinning (CR = 2.25 to 2.7) the AlF _-2 ^- -ion is the predominant dissolved metal species. Other species (A1₂F₃ ^-, A1₃F₄-, A1₄F₅-) were found to be of some significance only in melts with high excess A1F₃ (CR < 2).     

Passivation of the aluminium cathode during deposition of aluminium from aluminium chloride-sodium chloride melts

The kinetics of aluminium deposition from NaCl-AlCl₃ melts (c_AlCl3 < 10 mol%) contained in alumina crucibles was studied by linear sweep voltammetry and potential step amperometry at temperatures around 820°C. At low concentrations (c_AlCl3 < 0.4 mol%) the reduction of AlCl₃ on liquid aluminium has been found to be diffusion controlled. At higher concentrations a passivation of the aluminium electrode was observed during the deposition reaction. The passivation appears to be caused by precipitation of alumina from supersaturated melt in the diffusion layer at the aluminium cathode.     

Development and characterization of a biocompatible OH-modified copolymer based on polyurethane

Different polyurethanes were synthesized by varying the diol as well as the diisocyanate components and chain extenders. Polyurethanes with OH-groups were obtained by photo- and thermoinitiation of the radical polymerization of hydroxy alkyl acrylates in the presence of the polyurethanes. The polymers were evaluated with respect to their biocompatibility by measuring the cell spreading, the rates of DNA- and protein synthesis and the swelling behaviour. The differences in the surfaces and the bulks between the selected basic polyurethane and the functionalized modification were determined and characterized by XPS, FTIR-ATR and ¹³C-FT-NMR-spectroscopy. The mechanical data of Tecoflex EG 60D® and Pellethane 2363–80AE® were compared with the data of the synthesized polyurethanes.