Physical modeling of gas/liquid mass transfer in a gas stirred ladle

The absorption of gas through the plume eye and of an injected gas in a steelmaking ladle process was investigated, using a physical model of CO₂ absorption into a NaOH solution. The results show that the inert gas escaping through the plume eye is ineffective in protecting the bath from the atmosphere, and placing an oil layer (simulated slag) decreases the absorption rate significantly. Increasing the flow rate of the inert gas not only exposes more of the liquid surface to the CO₂ atmosphere, but also increases the mass transfer coefficient at the surface. The overall mass transfer between an injected CO₂ gas and NaOH solution includes the mass transfer through the surface of the bath as well as the mass transfer in the bubble dispersion zone. The difference between the mass transfer in the bubble dispersion zone and the overall mass transfer was found to be significant for relatively low gas flow rates. The mass transfer coefficient of CO₂ in the bubble dispersion zone was estimated using available information regarding the bubble size and velocity. Mass transfer coefficient estimated for the constant bubble frequency regime shows a dependence on gas flow rate. However, if a constant characteristic size of bubbles is assumed as an alternative approach, the mass transfer coefficient is independent of the gas flow rate.     

High dielectric constant thin film EBG power/ground network for broad-band suppression of SSN and radiated emissions

We experimentally demonstrated the great advantages of a high dielectric constant thin film electromagnetic bandgap (EBG) power distribution network (PDN) for the suppression of power/ground noises and radiated emissions in high-performance multilayer digital printed circuit boards (PCBs). Five-layer test PCBs were fabricated and their scattering parameters measured. The power plane noise and radiated emissions were measured, investigated and related to the PDN impedance. This successfully demonstrated that the bandgap of the EBG was extended more than three times, covering a range of hundreds of MHz using a 1-cm /spl times/ 1-cm EBG cell, the SSN was reduced from 170 mV to 10 mV and the radiated emission was suppressed by 22 dB because of the high dielectric constant thin film EBG power/ground network.     

W-band divide-by-3 frequency divider using 0.1 /spl mu/m InAlAs/InGaAs metamorphic HEMT technology

A W-band divide-by-3 frequency divider with wide bandwidth and low power dissipation is presented using harmonic injection-locking technique. A cascode FET is employed for a self-oscillating second-harmonic mixer which is injection-locked by third-harmonic input to obtain the division order of three. The fabricated frequency divider using 0.1 /spl mu/m GaAs metamorphic HEMT technology shows superior performance such as large bandwidth of 6.1 GHz around 83.1 GHz (7.3%) under small DC power consumption of 12 mW.     

Stimulation of negative magnetoresistance by an electric field and light in silicon doped with boron and manganese

It is experimentally ascertained that light stimulates the negative magnetoresistance observed in a high electric field in silicon doped with boron and manganese. The optimum conditions (the electric field, temperature, illumination, and resistivity of the material) for observation of the largest magnitude of negative magnetoresistance in (Si:B):Mn are determined. The dependence of the negative magnetoresistance on the concentration of compensating impurity is established.     

A 0.6–2.7 GHz Semidynamic Frequency Divide-by-3 Utilizing Wideband RC Polyphase Filter in 0.18 $mu$m CMOS

A wideband complementary metal oxide semiconductor (CMOS) semidynamic frequency divide-by-3 covering more than two octave bandwidths is presented. The wideband operation without requiring a quadrature signal source is realized by employing a three-stage RC polyphase filter. The transfer function analysis on Type-II two- and three-stage polyphase filters is performed to provide analytic solutions of the peak phase error and peak attenuation. Implemented in 0.18 mum CMOS, the divide-by-3 operates over the input frequency range between 0.6 and 2.7 GHz while dissipating 15 mA from a 1.8 V supply.     

Influence of the preparation conditions on the size and morphology of nanocrystalline lanthanum orthoferrite

Nanocrystalline LaFeO₃ is prepared by the dehydration of coprecipitated lanthanum and iron(III) hydroxides. It is shown that the behavior of the samples during heating and the size distribution of LaFeO₃ nanocrystals can be considerably different depending on the scheme used for coprecipitation of lanthanum and iron hydroxides; independently of the method employed for coprecipitation of the initial compounds, sintering of the samples at 950°C leads to the formation of lanthanum orthoferrite crystals up to 100 nm in size.     

Production and structural features of a water-soluble polysaccharide from a mutant strain of Agrobacterium sp.

We have developed a mutant strain derived from Agrobacterium sp. ATCC 31750, which produces a water-soluble polysaccharide having potential utility to the food, feed, pharmaceutical and cosmetic industries. A high concentration of product (15 g/L) is obtained by 48 h cultivation of the mutant strain under optimized fermentation conditions. The water-soluble polysaccharide obtained from cultures of the mutant strain beta82 has Glc:Man:Gal in approximate molar ratios of 5.8:6.7:1.0. The molecular weight of the polysaccharide was determined to be approximately 1000 kDa by HPSEC analysis. Linkage analysis contained 3-Glcp, 3-Manp, terminal Glcp and terminal Manp, as well as a small proportion of 3- and 3,4-Galp, and 4,6-Manp residues. Based on analyses using FT-IR and ¹³C NMR spectrometers, most glycosidic bonds joining these sugar residues are of the α-type, and acetyl groups are apparently attached to the polymer chain at random.     

Dye adsorption characteristics of alginate/polyaspartate hydrogels

This study examined the removal of some basic dyes, such as Methylene Blue, Malachite Green and Methyl Orange, using alginate or alginate/polyaspartate composite gel beads. The adsorption of dyes from aqueous solutions at 25 °C was examined using a batch sorption technique. The effects of CaCl₂ and the dye concentration on the adsorption were examined. Type-S adsorption isotherms were obtained, which is characteristic of a weak solute–solid interaction. The ionic interaction between the dye molecule and gel matrix appears to be responsible for the efficient adsorption of cationic dyes in this system. These results suggest that an alginate/polyaspartate gel can be used as an effective sorbent for water pollutants such as dyes, and the immobilization of these organic contaminants in the hydrogels from wastewater can solve one of the most important environmental problems in the related industry.