Bulletin of Engineering Geology and the Environment - Water seepage from dam foundations causes reservoir water loss and raises the risk of dam instability. One method of remediation for... 相似文献
Catalysis Letters - In this work, without using any linker or chemical modification of graphene oxide, a zinc oxide immobilized graphene oxide-based catalyst was used for the direct aerobic... 相似文献
The research was carried out to develop geopolymers mortars and concrete from fly ash and bottom ash and compare the characteristics deriving from either of these products. The mortars were produced by mixing the ashes with sodium silicate and sodium hydroxide as activator solution. After curing and drying, the bulk density, apparent density and porosity, of geopolymer samples were evaluated. The microstructure, phase composition and thermal behavior of geopolymer samples were characterized by scanning electron microscopy, XRD and TGA-DTA analysis respectively. FTIR analysis revealed higher degree of reaction in bottom ash based geopolymer. Mechanical characterization shows, geopolymer processed from fly ash having a compressive strength 61.4 MPa and Young's modulus of 2.9 GPa, whereas bottom ash geopolymer shows a compressive strength up to 55.2 MPa and Young's modulus of 2.8 GPa. The mechanical characterization depicts that bottom ash geopolymers are almost equally viable as fly ash geopolymer. Thermal conductivity analysis reveals that fly ash geopolymer shows lower thermal conductivity of 0.58 W/mK compared to bottom ash geopolymer 0.85 W/mK. 相似文献
The thermomechanical behavior of micro/nano-alumina (Al2O3) ceramics reinforced with 1-5 wt.% of acid-treated oil fly ash (OFA) was investigated. Composites were sintered using spark plasma sintering (SPS) technique at a temperature of 1400°C by applying a constant uniaxial pressure of 50 MPa. It was evaluated that the fracture toughness of micro- and nanosized composites improved in contrast with the monolithic alumina. Highest fracture toughness value of 4.85 MPam1/2 was measured for the nanosized composite reinforced with 5 wt.% OFA. The thermal conductivity of the composites (nano-/microsized) decreased with the increase in temperature. However, the addition of OFA (1-5 wt.%) in nanosized alumina enhanced the thermal conductivity at an evaluated temperature. Furthermore, a minimum thermal expansion value of 6.17 ppm*K−1 was measured for nanosized Al2O3/5 wt.% OFA composite. Microstructural characterization of Al2O3-OFA composites was done by x-ray diffraction and Raman spectroscopy. Oil fly ash particles were seen to be well dispersed within the alumina matrix. Moreover, the comparative analysis of the nano-/microsized Al2O3/OFA composites shows that the mechanical and thermal properties were improved in nanosized alumina composites. 相似文献
In this article, the catalytic conversion of methanol to gasoline range hydrocarbons has been studied over CuO/ NH4‐ZSM‐5(3,5,7,9%) catalysts prepared via sono‐chemistry methods. In order to improve, copper oxide can be used as a booster on NH4‐ZSM‐5 this catalyst property. Accordingly, the conversion process of Methanol to Gasoline (MTG) was conducted under a pressure of 1 atm and temperature of 400°C by a fixed‐bed reactor on copper oxide catalysts which were prepared based on synthetic NH4‐ZSM‐5. The synthetic catalyst was investigated by such analyses as BET, XRD, FT‐IR, and SEM. Formation of copper oxide phase and proper distribution of copper oxide were proven on the basic level of using XRD analysis. BET analysis showed the reduction in catalyst level and SEM images depicted the proper distribution of particles. The present investigation is to study the effect of CuO loading on NH4‐ZSM‐5 support for conversion of methanol to gasoline range hydrocarbons. A series of CuO/ NH4‐ZSM‐5 catalysts were prepared, characterized, and experimented for their performance on methanol conversion and hydrocarbon yield. 相似文献
In this article, a powder‐bed class of additive manufacturing (AM) is incorporated into the manufacturing of graphene nanocomposite 3D structures. For AM of graphene‐based 3D structures, graphene oxide (GO)/hydroxyapatite (Hap) nanocomposite (GHN) was synthesized at different GO to Hap percentage (wt.%), including 0.2% and 0.4% to develop a printable powder. The synthesized powder was utilized in a powder‐bed AM system to fabricate 3D porous structures of GHN powder. It was shown that at layer thickness of 125 μm and core binder saturation level of 400%, the compressive mechanical strength of the samples with higher content of graphene was improved significantly. 相似文献
This paper updates a method for generating small, accurate kinetic models for applications in computational fluid dynamics programs. This particular method first uses a time-integrated flux-based algorithm to generate the smallest possible skeletal model based on the detailed kinetic model. Then, it uses a multi-stage optimization process in which multiple runs of a genetic algorithm are used to optimize the rate constant parameters of the retained reactions. This optimization technique provides the user with the flexibility needed to balance the fidelity of the model with their time constraints. The updated method was applied to the reduction of a methane-air model under conditions meant to approximate the end of a compression stroke of an internal combustion engine. When compared to previous techniques, the results showed that this method could produce a more accurate model in considerably less time. The best model obtained in this study resulted in relative errors ranging from 0.22 to 1.14% on all six optimization targets. This reduced model was also able to adequately predict optimization targets for certain operating conditions, which were not included in the optimization process.
Diffusion joining of commercially pure titanium was successfully prepared via transient liquid phase bonding in vacuum environment. The process was carried out using AMS 4772 silver-based filler alloy at 900–1000°C for various holding time under the vacuum of 6?×?10?7?Torr. Optical and scanning electron microscopy equipped with an EDS analyzer was conducted for microstructural evaluations. Mechanical properties were also investigated by shear test, fractographic assessment and X-ray diffraction analyses. The tendency to achieve isothermally solidified joint increased by increasing bonding time. No sign of athermal solidification was detected of sample bonded at 1000°C for 90?min. Consequently, the bonding condition of a high quality joint was obtained. Elemental analyses revealed that filler alloy’s elements (Ag, Cu) distributed more uniformly in fully isothermal solidified bond, whereas the aggregation of these elements is considerable in athermally solidified bond. Shear test results represented that the highest shear strength attributed to the sample bonded in isothermal solidified condition (bonded at 1000°C for 90?min). 相似文献