Method for correcting molecular weight from gel-permeation chromatography. I. Skewing and concentration corrections

The purpose of this paper is to present a metod to calculate real molecular weight averages of polymer samples from GPC chromatograms where the instrumental spreading functions are skewed and the concentration effect exists. In this method, it is assumed that (1) the skewed chromatograms of monodisperse polymer samples can be represented as resultant of halves of two different Gaussians, (2) the resolution factors are regarded as constant in the case of low sample loading, and (3) the peak elution volume is independent of the presence of other components in the case of low sample loading. Adequate monodisperse polystyrenes and the mixtures (binary, seven and ten components) were examined for this purpose; and the molecular weight averages calculated by this method were compared with the ones obtained by Rosen and Provder's method. From the results in our study, it is found that this method can be available for correcting molecular weight from GPC chromatograms except for very narrow high molecular weight samples.     

Effect of platelet-activating factor on lipoprotein lipase and blood lipids

We investigated the effect of platelet-activating factor (PAF) and of the PAF specific antagonist CV-6209 on plasma lipid metabolism, and particularly on post-heparin plasma lipolytic activity in male Wistar rats. Lipoprotein lipase (LPL) activity was enhanced by intravenous injection of PAF before intravenous injection of heparin when the PAF dose was low (0.2 μg/kg). PAF activated hepatic triacylglycerol lipase (HTGL) activity dose-dependently. Plasma triacylglycerols (TG) significantly decreased with the activation of LPL and/or HTGL. Plasma total cholesterol (TC) and phospholipid (PL) levels decreased at a low dose of PAF (0.2 μg/kg), but increased when higher doses were used. The PAF antagonist CV-6209 partially reversed the PAF induced effects on HTGL, TC and PL. Based on a paper presented at the Third International Conference on Platelet-Activating Factor and Structurally Related Alkyl Ether Lipids, Tokyo, Japan, May 1989.     

OXIDATION OF SULFUR DIOXIDE IN DIFFERENT TYPES OF THREE PHASE REACTORS

Five different types of three-phase reactors are compared with each other by using oxidation of sulfur dioxide on activated carbon. The kinetic measurements were carried out by changing concentrations of sulfur dioxide from 0.04 to 0.17% (volume) and those of oxygen from 2 to 21%. The reaction rate was 0.2 order with respect to sulfur dioxide and 0.5 order with respect to oxygen. The catalytic effectiveness factor and intraparticle diffusivity were evaluated by changing particle sizes of activated carbon from 0.03 to 1.6 mm. Resistances of gas-liquid, liquid-solid mass transfer and intraparticle diffusion were estimated for individual reactors. The optimum reactor was dependent on operating conditions such as gas flow rates, rotating speeds and particle sizes.     

Ethylene carbonate-based organic electrolytes for electric double layer capacitors

A new electrolytic solution based on a mixed solvent of ethylene carbonate (EC) with sulfolane (SL) or -butyrolactone (-BL) has been examined as an electric double layer capacitor. Fundamental properties, such as electrolytic conductivity, viscosity, and thermal stability, were measured for solutions containing quaternary alkylammonium salts as the supporting electrolyte. Maximum conductivities were obtained for the solutions with mixed solvent of 20–40 mol % EC in the EC+-BL system: 1.2–1.3×10^–2S cm^–1 for EC+-BL dissolving 0.5 M Et₄ NBF₄ (Et=C₂H₅). The electrochemical and the thermal stabilities of the solution were dependent on the electrolytic salt as well as the solvent composition. A stable discharge capacitance and a high coulombic efficiency were obtained in a model capacitor using carbon fibre electrodes and the organic electrolyte of EC+-BL/Et₄NBF₄ (or EC+-BL/Et₄NPF₆).     

Application of the Solvothermal Process in the Synthesis of High-performance Ag/γ-Al_2O_3 Catalysts

1 INTRODUCTION Since Cu-ZSM-5 was reported as an effective catalyst for the selective catalytic reduction (SCR) of NO by hydrocarbons in the presence of excess oxygen, the SCR of NOx has received much attention as a kind of potential technology for cleaning NOx in various oxygen-rich exhausts of diesel engine, lean burning gasoline engine and gas engine. Although a number of catalysts have been tested, to date, it still seems to be difficult to find a catalyst that is completely suit…     

Morphology study of oriented SmBCO film deposited by MOCVD

c-axis-oriented SmBa_2Cu_3O_7(SmBCO) films have been deposited on(100)- LaA1O_3(LAO)substrate by metal organic chemical vapor deposition(MOCVD) technique.The effects of deposition temperature(T_(dep)) and total pressure(P_(tot)) on the orientation and microstructure of SmBCO films were investigated.The orientation of SmBCO films transformed from α-axis to c-axis with increasing of T_(dep) from 900 to 1 100℃.At T_(dep)=1 050℃,SmBCO films had c-axis orientation and tetragon surface.At P_(tot)~(dep)=400-800 Pa and T_(dep)=1 050 ℃,totally c-axis-oriented SmBCO films were obtained.The R_(dep) of SmBCO films increased firstly and then decreased with increasing P_(tot).The surface of SmBCO films exhibited tetragon morphology at 1 050 ℃ and400 Pa.Maximum thickness of SmBCO film deposited was 1.2μm at P_(tot)= 600 Pa,and the corresponding R_(dep)was 7.2 μm·h~(-1).     

Fine TiC dispersed Al2O3 composites fabricated via in situ reaction synthesis and conventional process

To further improve the mechanical performance and reduce the percolation threshold by controlling microstructures, Al₂O₃-TiC composites containing 0-20 vol% TiC were fabricated via in situ reaction synthesis. Graphite (ATC) and carbon nanotubes (ATCT) were used as carbon sources. The composites were also fabricated via a conventional process using a TiC starting powder (AT). X-ray diffraction analysis and scanning electron microscopy observation results indicated successful fabrication of the composites with various microstructures. TiC particles in ATCT were completely dispersed at grain boundaries, whereas in ATC and AT, these particles were either intragranular or intergranular dispersed. The composites could be listed as follows, ATCT > ATC > AT, that is, in descending order of the reinforcing flexural strength and fracture toughness. The nanoindentation measurement indicated the optimum hardening effect of ATCT. The ATCT composite also exhibited the highest fracture toughness, which was 49% higher than that of the monolithic Al₂O₃. Crack deflection was considered as the main toughening mechanism while crack bridging behavior also occurred in ATCT. For a given TiC content, ATCT exhibited the lowest electrical resistivity, owing mainly to the complete grain-boundary dispersion of the relatively large TiC particles. The similarity of the Al₂O₃ grain size and TiC particle size of ATCT contributed to the lowest percolation threshold achieved (11.2%), which (to date) is the lowest value that has been reported for the Al₂O₃-TiC system.     

Relation between crystal structure and lattice oxygen content of sintered reaction-bonded silicon nitride

When reaction-bonded silicon nitride containing MgO/Y₂O₃ additives is sintered at three different temperatures to form sintered reaction-bonded silicon nitride (SRBSN), the thermal conductivity increases with sintering temperature. The β-Si₃N₄ (silicon nitride) crystals of SRBSN ceramics were synthesized and characterized to investigate the relation between the crystal structure and the lattice oxygen content. The hot-gas extraction measurement result and the crystal structure obtained using Rietveld analysis suggested that the unit cell size of the β-Si₃N₄ crystal increases with the decrease in the lattice oxygen content. This result is reasonable considering that the lattice oxygen with the smaller covalent radius substitutes nitrogen with the larger one in the β-Si₃N₄ crystals. The lattice oxygen content decreased with increasing sintering temperature which also correlated with increase in thermal conductivity. Moreover, it is noteworthy from the viewpoint that it may be possible to apply the lattice constant analysis for the nondestructive and simple measurement of the lattice oxygen content that deteriorates the thermal conductivity of the β-Si₃N₄ ceramics.     

Applying MHD technology to the continuous casting of steel slab

The application of magnetohydrodynamics (MHD) in the continuous casting process started with the electromagnetic stirring of the stand pool with a traveling magnetic field. It has now advanced to the electromagnetic stirring of molten steel in the mold and the control of molten steel flow by an in-mold direct current magnetic field brake. These applied MHD techniques are designed to further improve the continuous casting process capability. They improve the surface quality of cast steel by homogenizing the meniscus temperature, stabilizing initial solidification, and cleaning the surface layer. They also improve the internal quality of cast steel by preventing inclusions from penetrating deep into the pool and promoting the flotation of argon bubbles. Applied MHD technology is still advancing in scope and methods in addition to the improvement of conventional continuously cast slab qualities. The continuous casting of bimetallic slab by suppressing mixing in the pool is one example of this progress.     

Development of a robot assisted carotid blood flow measurement system

The ultrasound diagnosis of the carotid artery is one of the most common non-invasive methods to detect early stage heart and cerebrovascular diseases. However, the precision and repetitiveness of the probe positioning depend exclusively on the operator's skills and dexterity. For this purpose, we propose the development of a robot assisted system to enhance the accuracy and repetitiveness of the probe positioning to measure the wave intensity (WI) index. In this paper, the Waseda-Tokyo Women's Medical-Aloka Blood Flow Measurement Robot System No. 2 Refined (WTA-2R) is presented. The WTA-2R consists of a conventional ultrasound diagnosis system, a 6-DOFs parallel link slave manipulator, a 6-DOFs serial link passive arm, and a master device. Experiments were carried out to verify its effectiveness in terms of accuracy and required time to perform the task. From the experimental results, the positioning accuracy and reduction of required time were confirmed.