High Hardness and Ductile Mosaic SiC/SiO2 Composite by Spark Plasma Sintering

SiC powder was coated with SiO₂ layer by chemical vapor deposition, and the SiC(core)/SiO₂(shell) composite powder was consolidated to a SiC/SiO₂ composite with a mosaic microstructure by spark plasma sintering (SPS) at 1923 K for 1.8 ks. The SiC(core)/SiO₂(shell) powder with a 80–100 nm thick SiO₂ layer resulted in a SiC/SiO₂ composite with a relative density of 97% and hardness and fracture toughness of 17.1 GPa and 8.4 MPa m^1/2, respectively.     

Textile‐surface interfacial asymmetric polymerization

This research demonstrated that polymerization of aniline on cellulose produces chiroptically active composites. Polymerization of aniline in the presence of cotton fibers consisting of chiral cellulose are performed to prepare a polyaniline (PANI)/cotton composite. The polymerization is conducted at the cotton interface. The resultant PANI/cotton composite shows chiroptical activity elucidated with diffuse reflectance circular dichroism. In this reaction, textile‐surface interfacial asymmetric polymerization is performed with imprinting of chiral structure from the cotton as a natural chiroptically active polymer to the PANI. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41118.     

Numerical analysis of a dual refluxed PSA process during simultaneous removal and concentration of carbon dioxide dilute gas from air

The simultaneous removal and concentration of carbon dioxide present in ambient air were carried out by a dual refluxed Pressure Swing Adsorption (PSA) process with intermediate feed inlet position. The feed inlet position divides each column into rectifying and stripping sections from which enriched and lean gases can be simultaneously produced. A simple isothermal model with negligible axial dispersion and pressure drops through the PSA beds was developed to investigate the effects of various combinations of the operating variables and to analyze semi-quantitatively the effects of the main characteristic parameters such as the dimensionless feed inlet position (Z_R/L_T) and the stripping-reflux ratio (R_r). A good agreement between the model prediction and the experimental results was obtained. Moreover, an optimum feed inlet position was found and it corresponded to a position where the carbon dioxide mole ratio in the feed flux and that in the upstream flux leaving the stripping section were equal. The carbon dioxide mole ratio in the enriched product (Y_E) as well as that in the lean product (Y_L) were strongly dependent on the ratio of feed/enriched product flow rates (Q_F/Q_E) and the ratio of feed/lean product flow rates (Q_F/Q_L). Although the pressure ratio (P_a/P_d) was crucially important for the separation performance, a smaller value of R_r was sufficient to reach a performance which is unattainable in conventional PSA processes.     

Immobilization of alkaline phosphatase on magnetic particles by site-specific and covalent cross-linking catalyzed by microbial transglutaminase

Bacterial alkaline phosphatase (BAP) was site-specifically and covalently immobilized on magnetic particles (MPs) using the enzymatic reaction of microbial transglutaminase (MTG). Immobilization efficiency was affected by the chemical surface treatment of MPs and immobilized BAP exhibited more than 90% of the initial activity after 10 rounds of recycling.     

Detection of Leuconostoc strains at a meat processing plant using polymerase chain reaction

To simplify the labor-intensive conventional routine testing of samples to detect Leuconostoc at a meat processing plant, we developed polymerase chain reaction (PCR) primers specific for Leuconostoc from 16S rRNA gene sequences. These primers did not detect other common lactic acid bacteria such as Lactobacillus plantarum, Lact. sake, Lact. fermentum, Lact. acidophilus and Weissella viridescens. PCR with this primer detected all Leuconostoc species tested (Leu. mesenteroides subsp. mesenteroides, Leu. pseudomesenteroides, Leu. carnosum, Leu. lactic, Leu. citreum, Leu. amelibiosum, Leu. gelidum), except for Leu. fallax, and no other lactic acid bacteria on agarose gel electrophoresis. The method could identify areas contaminated with Leuconostoc in a large-scale industrial meat processing plant. Of 69 samples analyzed, 34 were positive for Leuconostoc according to the conventional culture method (isolation of LAB producing dextran) and PCR, whereas 29 were negative according to both. Six samples were culture-negative but positive by PCR. No false negative results were generated by PCR. The method is rapid and simple, is useful for routinely monitoring areas contaminated with Leuconostoc in meat processing plants, and could help to prevent the spoilage of meat products.     

Determination of Ethyl Carbamate in Sake Using Headspace Solid Phase Microextraction

An analytical method for the determination of ethyl carbamate in alcoholic beverages has been developed and optimized. A combination of headspace solid phase microextraction (HS‐SPME), as the extraction technique, and GC/MS, as the determination technique, was utilized. Analytical grade ethyl carbamate dissolved in ethanol solution was analyzed to determine the optimum analytical conditions. Ethyl carbamate‐d₅ was added as an internal standard. The following HS‐SPME conditions were investigated: type of stationary phase of the fibre, ethanol content, sample volume and extraction time. The optimized procedure showed that the detection limit, relative standard deviation, and recovery were 6.7 μg/L, 0.4–2.0%, and 103.6–107.6%, respectively. The precision of this new method was equivalent to previous analyses. Finally, the developed method was applied to the analysis of ethyl carbamate in sake.     

Mass transfer and holdup in gas-liquid cocurrent flow packed beds containing water-repellent particles

Water-repellent particles were prepared by spraying polytetrafluoroethylene (PTFE) on activated carbon. Gas-liquid volumetric mass transfer coefficient and holdup were determined in gas-liquid cocurrent upflow and downflow packed beds from the measurements of gas desorption and volume, respectively. As the PTFE loading increased, the gas-liquid volumetric mass transfer coefficients in both upflow and downflow modes were enhanced. Gas holdup in the upflow mode increased with the PTFE loading, while the dynamic liquid holdup in the downflow mode decreased. The enhancement of the mass transfer rate from gas to liquid can be explained by the effect of water-repellency on the surface of activated carbon.     

Chemical‐Free Approach for Z‐Isomerization of Lycopene in Tomato Powder: Hot Air and Superheated Steam Heating above the Melting Point of Lycopene

Z‐isomers of lycopene exhibit higher bioavailability and antioxidant capacity than those of the all‐E‐isomer. Therefore, it is important to develop an efficient and environmentally friendly procedure for Z‐isomerization. The current methods for Z‐isomerization of (all‐E)‐lycopene use toxic chemicals such as organic solvents and catalysts. This study is aimed to develop a chemical‐free method for Z‐isomerization of (all‐E)‐lycopene in tomato powder by hot air and superheated steam heating. The Z‐isomerization reaction is promoted by heating above the melting point of lycopene. When heated with superheated steam, the thermal decomposition of lycopene is suppressed compared to that when heated with hot air. When tomato powder is heated at 240 °C for 5 min by superheated steam, the total Z‐isomer content and remaining lycopene are 69.0% and 90.7%, respectively, while with hot air heating, the total Z‐isomer content and remaining lycopene are 69.9% and 68.0%, respectively. These results indicate that the thermal Z‐isomerization of lycopene occurs in the molten state and heating in a low oxygen atmosphere suppresses the thermal decomposition of lycopene. Practical Applications: Tomato powder rich in lycopene Z‐isomers is an important ingredient for the food and animal feed industries. Since Z‐isomers of lycopene are more soluble in solvents including ethanol which is a low‐toxicity and environmentally friendly solvent, the efficiency of lycopene extraction with ethanol can be improved by using the Z‐isomer‐rich tomato powder as a raw material. The obtained Z‐isomer‐rich extract has a high added value because the Z‐isomers have higher bioavailability and antioxidant capacity than those of the all‐E‐isomer. In addition, since lycopene Z‐isomers exhibit higher accumulation efficiency and better color improvement in hen egg yolks than those of the all‐E‐isomer, Z‐isomer‐rich tomato powder is an effective animal feed.     

High Intensity Operation at Naoshima Smelter

This paper describes the successful test operation of a 50 t/h concentrate feed rate (or on the anode copper basis 9000 tlm) with the Mitsubishi Process. Particular emphasis is given to the analyses of the furnace capacity by the measurement of flow pattern and oxygen potential. Smelting rate on the unit hearth area of the smelting furnace is now one-ton of concentrate/m²·h. The results of the analyses show the further potential of the furnace capacity of the process.     

Synergistic effect of Pt or Pd and perovskite oxide for water gas shift reaction

The water gas shift (WGS) reaction over Pt and Pd catalysts supported on various perovskite oxides has been investigated at 573 K without catalyst pretreatment. The Pt and Pd catalysts on LaCoO₃ support showed high catalytic activity. Interaction between Pt or Pd and the support is considered to promote the WGS reaction: Pt/LaCoO₃ had high initial activity but deactivated immediately; Pd/LaCoO₃ was less active than Pt/LaCoO₃, but had superior stability. Catalysts were characterized using XRD, STEM, XPS, and H₂-temperature programmed reduction (TPR). Results of this study showed that reduction of the support decreased the CO conversion on Pt/LaCoO₃. On the other hand, Pd/LaCoO₃ showed stable activity for the WGS reaction. Therefore, Pd was added to Pt/LaCoO₃ for stabilizing the catalyst activity, and 0.5 wt.% Pd/1 wt.% Pt/LaCoO₃ catalyst showed higher activity and stability.