Study of Hydrodynamics,Mixing and Gas‐Liquid Mass Transfer in a Split‐Rectangular Airlift Reactor

Global hydrodynamic characteristics, liquid mixing and gas‐liquid mass transfer for a 63 L split‐rectangular airlift reactor were studied. Correlations for gas holdup and overall liquid circulation velocity were derived for the air‐water system as a function of the specific power input; these were compared to data and correlations for reactor volumes between 4.7 L and 4600 L. A partial recirculation of small bubbles in the riser was observed when U_gr > 0.03 m/s, which was attributed to the use of a single‐orifice nozzle as the gas phase distributor. The dimensionless mixing time and the overall axial dispersion coefficient were nearly constant for the range of gas flow rates studied. However, values of K_L/d_B were greater than those reported in previous studies and this is caused by the partial recirculation of the gas phase in the riser. While scale effects remain slight, the use of a gas distributor favouring this partial recirculation seems adequate for mass transfer in split‐rectangular airlift reactors.     

Modification of leather properties by grafting. I. Effect of monomer chain on the physico‐mechanical properties of grafted leather

Although leather has a number of desirable properties such as thermal stability and fire retardancey, in addition to high toughness, it has a few drawbacks such as weight, high water absorption, poor soil and rot resistance, and nonuniformity. If these defects are overcome, leather's usefulness would be further enhanced and its competitive position with respect to synthetics would increase. This study reports the physical and mechanical properties of buffalo leather after chemical graft copolymerization with ethyl acrylate, butyl acrylate, and 2‐ethyl hexyl acrylate using benzoyl peroxide as an initiator. The optimum conditions for grafting (e.g., monomer and initiator concentrations, temperature and time of grafting, and solvent leather ratio) were extensively investigated. The study achieved outstanding properties for buffalo leather in reduction of water uptake after grafting, especially on using 2‐ethyl hexyl acrylate and butyl acrylate monomers. FT‐IR and solid ¹³C‐NMR for leather before and after grafting confirmed the grafting process.© 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1478–1483, 2003     

Functional properties of a protein product from Caryodendron orinocense (Barinas nut)

The functional properties of Caryodendron orinocense protein product were investigated and compared with those of soybean (Glycina maxima). The product protein content was 24.47 g/100 g (Nx6.25). Solubility increased at both sides of the isoelectric point (pH 4.0) and with increased NaCl concentration up to 0.5M. Compared with soybean flour (50% protein), the protein product exhibited higher water and oil absorption, but lower emulsifying activity, emulsion stability, foaming capacity, and foam stability, the last one increase at higher pH. Emulsifying activity, foaming capacity, and foam stability were ionic strength dependent. C. orinocense protein product increased its emulsifying activity steadily from 0.05M to 0.75M NaCl, while it remained almost constant for soybean flour. Foaming capacity increased drastically at pH 10. The minimum time and concentration to form a gel was 20% in 4 min and 10% in 8 min for the Caryodendron protein product and soybean flour, respectively. The bulk density was 0.5056+/-0.0041 g/mL.     

Grafting poly(t‐butyl acrylate) to poly(allylamine) by inverse microemulsion radical polymerization: From comb‐polymer to amphiphilic shell crosslinked polymer nanocapsule

An interfacial grafting radical polymerization method for amphiphilic comb copolymer and shell crosslinked polymer nanocapsules was reported. Macropolyradicals on a water soluble long chain polyamine were generated with hydrogen peroxide in the water phase and subsequent grafting radical polymerization of a vinylic monomer at the water/oil interface proceeded at 65°C. In the presence of a crosslinker, the resulting graft copolymer formed a defined core‐shell structure with hydrophilic aqueous core functionalized by the polyamine and a hydrophobic crosslinked polymer shell. The structure of the core‐shell material was characterized by NMR, FTIR, DSC, TGA, SEM, TEM, and the mechanism of the graft polymerization is proposed. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 1905–1911, 2007     

Lignin‐based polycondensation resins for wood adhesives

Lignin‐based wood adhesives are obtained that satisfy the requirements of relevant international standards for the manufacture of exterior‐grade wood particleboard. Formulations based on low molecular mass lignin and presenting an increase in the relative proportion of reactive points yield better results than the higher molecular mass lignin used in the past. These lignins allow a higher proportion of hydroxymethylation during preparation of methylolated lignins. These lignin‐based adhesives also yield acceptable results at particleboard pressing times that are sufficiently low to be of industrial significance. Lignin‐based wood adhesives, in which a nonvolatile nontoxic aldehyde (glyoxal) is substituted for formaldehyde in their preparation, are prepared and tested for application to wood panels such as particleboard. The adhesives yield good internal bond strength results for the panels, which are good enough to comfortably pass relevant international standard specifications for exterior‐grade panels. The adhesives also show sufficient reactivity to yield panels in press times comparable to that of formaldehyde‐based commercial adhesives. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1690–1699, 2007     

In vitro effects of urease inhibitors on rate of urea hydrolysis in soils

We studied the effect of urease inhibitors on the urea hydrolysis in some Sundanese soils belonging to the orders of Vertisol and Entisol. The hydrolysis showed a lag period of about 3 days and its rate (Y) per unit time (t) could be described by a two constants exponential equation of the general form Y = K₁t^K ₂. Statistical analysis showed that the intercept K₁ (rate of urea hydrolysis) was significantly affected by soil type rather than treatment. It seems that K₁ is associated with the soils' initial urease activity as it closely correlates with the Michaelis constant (km).The gradient, K₂, being significantly affected by soil type as well as treatment is probably associated with the induced urease activity with time and it, therefore, varied with variations in soils and treatments. Of the so-called urease inhibitors used in this study Ca(OH)₂, p-benzoquinone (PBQ) and orthophosphoric acid (OP) only PBQ reduced urea hydrolysis while the other chemicals have effects possibly related to modifying the soil pH. Inhibitor treated soils had substantial amounts of unacounted for N which was believed to be present, presumably, in the form of carbamate.Contribution from the Department of Biochemistry and Soil Science, Faculty of Agriculture, Shambat, Sudan.     

Electrochemical Behaviour of Al, Al—In and Al–Ga–In Alloys in Chloride Solutions Containing Zinc Ions

The electrochemical behaviour of Al, Al—In and Al–Ga–In alloys in 0.6 m NaCl solutions with and without Zn²⁺ was investigated. The study was performed by means of open circuit potential, potentiodynamic polarization, potentiostatic current-time and electrochemical impedance spectroscopy measurements as well as by SEM-EDAX examination. It was found that the Al—In alloy exhibits the highest negative open circuit potential in 0.6 m NaCl and the corrosion resistance of the tested electrodes decreases in the following order: Al > Al–Ga–In > Al—In. The greater activity of the Al—In alloy was interpreted on the basis of the autocatalytic attack by indium. The potentiostatic current–time measurements in Zn²⁺ containing electrolyte at potentials above the pitting potential revealed that Zn²⁺ has an insignificant influence on the Al electrode, while it enhances the corrosion of the Al–Ga–In alloy and improves the attack morphology of the Al—In alloy. Furthermore, the impedance spectra recorded under open circuit conditions showed a decrease in the polarization resistance of Al—In and Al–Ga–In alloys in presence of Zn²⁺ indicating the activating effect of Zn²⁺ ions.     

Evaluation of Polyester Resin as a New Compatibilizer for SBR/PVC Blends

A polyester (PE) based on the glycolyzed products of PET was prepared and added in different concentrations to a series of SBR/PVC blends. The addition of the polyester showed that all properties of SBR/PVC blends were improved by incorporation of PE. Highest mechanical strength values were obtained at a polyester concentration of 7.5 phr. Thermal analysis as well as dynamic mechanical properties of SBR/PVC blends after the addition of 7.5 and 10 phr polyester indicated one single glass transition temperature. The dielectric losses (?") were analyzed in the frequency domains in the two terms of Fröhlich related to the Maxwell Wagner effect and the orientation of the aggregates caused by the movement of the main chain. The permittivity (?') values were found to increase by increasing the polyester content. This increase was followed by a decrease in the ?" up to a 7.5 phr polyester content after which no pronounced change was noticed.     

On the ‘curiosity’ of electrical self‐heating,static charge and electromagnetic shielding effectiveness from carbon black/aluminium flakes reinforced epoxy‐resin composites

This paper shows the wide application range (such as electrical self‐heating and electromagnetic shielding effectiveness) of composites consisting of conductive carbon black/aluminum flakes (CBA) filler and epoxy insulative matrix. The effect of CBA content on the network structure of epoxy matrix was investigated in detail. Static electrical conductivity increases linearly with the increase of filler concentration at the interface in epoxy composites. The large decrease of the conductivity as a function of the temperature is analyzed in terms of the negative temperature coefficient of conductivity (NTCC) effect. The influence of viscosity, surface energy and barrier highest energy on the NTCC behaviour in the composite is also considered. Based on these results, a new interpretation is proposed to explain the NTCC phenomena by computing the swelling force among conductive phases. The correlations of conductivity during the temperature cycling and activation energy were analyzed. The effects of dynamic ageing at various temperatures on the resistivity are reported. Current–voltage–temperature characteristics for epoxy with different contents of CBA were examined in detail. A model based on the law of energy conservation is proposed to calculate the specific heat and amount of heat dissipation. The static charge of the epoxy–CBA composites was estimated. The correlation between electromagnetic wave‐shielding effectiveness (EMS), conductivity and frequency of epoxy composites with different filler contents is also discussed. Furthermore, the effect of annealing on EMS of epoxy composites was examined. © 2002 Society of Chemical Industry     

Exploration of mesoporous structure of tunisian raw and acid-leached phosphate ore particles

Rock phosphate fractions were examined for their porous structure by nitrogen adsorption. The pore size distribution and the shape of pores does not seem to depend on the particle size. The specific surface area values present two regions, one above and one below that of the particles with 125 μrn diameter. Particles of a given size were leached with dilute phosphoric acid (1.5 mass% P₂O₅) at 25°C. It was observed that there is a widening of the initial pores during leaching. The particles collected at the initial period of the reaction are pitted and those collected at the final period are disintegrated.