Processing,microstructure, and mechanical properties of hot-pressed ZrB2 ceramics with a complex Zr/Si/O-based additive

Densification behavior, microstructure, and mechanical properties of zirconium diboride (ZrB₂) ceramics modified with a complex Zr/Si/O-based additive were studied. ZrB₂ ceramics with 5–20 vol.% additions of Zr/Si/O-based additive were densified to >95% relative density at temperatures as low as 1400°C by hot-pressing. Improved densification behavior of ZrB₂ was observed with increasing additive content. The most effective additive amount for densification was 20 vol.%, hot-pressed at 1400°C (∼98% relative density). Microstructural analysis revealed up to 7 vol.% of residual second phases in the final ceramics. Improved densification behavior was attributed to ductility of the silicide phase, liquid phase formation at the hot-pressing temperatures, silicon wetting of ZrB₂ particles, and reactions of surface oxides. Room temperature strength ranged from 390 to 750 MPa and elastic modulus ranged from 440 to 490 GPa. Vickers hardness ranged from 15 to 16 GPa, and indentation fracture toughness was between 4.0 and 4.3 MPa·m^1/2. The most effective additive amount was 7.5 vol.%, which resulted in high relative density after hot-pressing at 1600°C and the best combination of mechanical properties.     

Collaborative test of determination of iodine value in fish oils. 1. Reaction time and carbon tetrachloride or cyclohexane as solvents

Twenty-two laboratories participated in a collaborative test to determine the iodine value (IV) of eight samples of fish oil (four with IV<150, four with IV>150) with either carbon tetrachloride (AOCS Official Method Cd 1–25) or cyclohexane (AOCS Recommended Practice Cd 1b-87) as solvent and either 1 or 2 h of reaction time. Laboratories received coded duplicate samples (hidden duplicates) and carried out duplicate determinations on each oil by each solvent-time combination (open duplicates). Replacing carbon tetrachloride with cyclohexane resulted in a lower IV (P<0.001). The decrease averaged 1.6 IV units for low-IV oils and 3.8 IV units for high-IV oils; this difference in response of 2.2 IV units between low- and high-IV oils was significant (P<0.001). Increasing the reaction time had a relatively small effect (0.34±0.18). There was no interaction of reaction time with solvent or oil type. Cyclohexane caused emulsions, which made it difficult to titrate residual iodine and thus increased the variability of the determination. The repeatability standard deviations (s _r ), based on hidden duplicates, for 1-h reaction time with carbon tetrachloride and cyclohexane were 2.17 and 3.35, respectively. The corresponding reproducibility standard deviations were 2.73 and 4.53.     

Enhanced Visible-Light Photocatalytic Degradation of Humic Acid by Palladium-Modified Nitrogen-Doped Titanium Oxide

Palladium-modified nitrogen-doped titanium oxide (TiON/PdO) nanoparticles were synthesized by a sol–gel process, for visible-light-induced photocatalysis using humic acid (HA) as a target. Our work shows that palladium modification has strong effects on the optical and photocatalytic properties of nitrogen-doped titanium oxide (TiON) photocatalysts. TiON/PdO nanoparticles demonstrated an enhanced photocatalytic activity over TiON within a narrow range of palladium concentration. Beyond this range, the adverse effect of palladium modification was observed in the visible-light-induced degradation of HA. The effects of palladium modification are discussed in terms of its role in controlling electron–hole recombination.     

Microstructure and morphology of amine-cured epoxy coatings before and after outdoor exposures—An AFM study

Atomic force microscopy (AFM) has been used to study the morphology and microstructure of an amine-cured epoxy before and after outdoor exposure. Measurements were made from samples prepared in an essentially CO₂-free, H₂O-free glove box and from samples prepared in ambient conditions. For those prepared in a CO₂-free glove box, AFM imaging was conducted on (1) an unexposed air/coating surface, (2) an unexposed coating bulk, (3) an unexposed coating/substrate interface, and (4) a field exposed air/coating surface. For samples prepared in ambient conditions, only the unexposed air/coating surface was investigated. The same regions of the exposed samples were scanned periodically by the AFM to monitor changes in the surface morphology of the coating as UV exposure progressed. Small angle neutron scattering and Fourier transform infrared spectroscopy (FTIR) studies were performed to verify the microstructure and to follow chemical changes during outdoor exposure, respectively. The results have shown that amine blushing, which occurs only under ambient conditions, had a significant effect on the surface morphology and microstructure of the epoxy. The surface morphology of the samples prepared under CO₂-free, dry conditions was generally smooth and homogeneous. However, the interface and the bulk samples clearly revealed a two-phase structure consisting of bright nodular domains and dark interstitial regions, indicating an inhomogeneous microstructure. Such heterogeneous structure of the bulk was in good agreement with results obtained by small angle neutron scattering of unexposed samples and by AFM phase imaging of the degraded sample surface. The relationship between submicrometer physical changes and molecular chemical degradation is discussed. Presented at the 82nd Annual Meeting of the Federation of Societies for Coatings Technology, October 27–29, 2004, in Chicago, IL.     

Effects of octadecanoid metabolites and inhibitors on induced nicotine accumulation inNicotiana sylvestris

We examined the effects of inhibitors of the octadecanoid pathway (n-propyl gallate, acetosalicylic acid, salicylhydroxamic acid, methyl salicylate, and antipyrine) on wound- and jasmonate-induced nicotine accumulation and compared the nicotine-inducing ability of exogeneous additions of linolenic acid (18:3) and its methyl ester, linoleic acid (18:2), abscisic acid, traumatic acid, and methyl dihydrojasmonate to the nicotine-inducing ability of exogenous additions of methyl jasmonate (MJ). The first four of these inhibitors significantly reduced wound-induced nicotine accumulation when applied in a lanolin paste to wounded tissues immediately after wounding at concentrations of 89–90µg/plant. When methyl salicylate and propyl gallate were mixed individually with MJ, neither inhibited MJ-induced nicotine synthesis, which suggests that the inhibitors block jasmonate synthesis or release from stored pools and not its effects. Linolenic acid or its methyl ester applied to undamaged plants or damaged plants (to either damaged or undamaged leaves) or to the roots of hydroponically growing plants did not induce nicotine accumulation or increase nicotine accumulation above levels found in damaged plants. Similarly, traumatic acid, linoleic acid, and abscisic acid did not induce nicotine accumulations. Methyl dihydrojasmonate, which is biosynthetically derived from linoleic acid, had 12–56% of the nicotine-inducing acitivity of MJ when added to the roots of hydroponically grown plants. The signal transduction pathway mediating wound-induced nicotine production therefore shares many features of the pathway eliciting wound-induced proteinase inhibitor production but differs in not being regulated at the lipase step in jasmonic acid production and not being responsive to abscisic acid.     

Defensive role ofAllium sulfur compounds for leek mothAcrolepiopsis assectella Z. (Lepidoptera) against generalist predators

It has been shown previously that sulfur volatiles produced byAllium plants affect the behavior of their specialist phytophages and of their specialist entomophages. The action of these compounds in protecting the leek mothAcrolepiopsis assectella against generalist entomophages was studied in comparison to the proposed original defensive role of these compounds against generalist herbivorous insects. Two ants species,Formica selysi andF. fusca, were used as generalist predators. Six behavioral criteria of the predatory behavior of the ants were studied in presence of the last-instar caterpillars (C₅). C₅ reared on artificial diets with or without leek components were tested, as well as C₅ soaked in frass of leek-reared caterpillars or disulfide solutions. In addition, the response of the ants to pure chemicals found in leek was studied using honey solutions with or without sulfur compounds. The sulfur allelochemicals ofAllium plants have a negative action on predatory ants. Interestingly, the nonvolatile precursors of sulfur volatiles ofAllium plants seem to have a protective role for their phytophagous insects against generalist entomophages.     

Large-scale in vivo synthesis of the carbohydrate moieties of gangliosides GM1 and GM2 by metabolically engineered Escherichia coli

Two metabolically engineered Escherichia coli strains have been constructed to produce the carbohydrate moieties of gangliosides GM2 (GalNAcbeta-4(NeuAcalpha-3)Galbeta-4Glc; Gal = galactose, Glc = glucose, Ac = acetyl) and GM1 (Galbeta-3GalNAcbeta-4(NeuAcalpha-3)Galbeta-4Glc. The GM2 oligosaccharide-producing strain TA02 was devoid of both beta-galactosidase and sialic acid aldolase activities and overexpressed the genes for CMP-NeuAc synthase (CMP = cytidine monophosphate), alpha-2,3-sialyltransferase, UDP-GlcNAc (UDP = uridine diphosphate) C4 epimerase, and beta-1,4-GalNAc transferase. When this strain was cultivated on glycerol, exogenously added lactose and sialic acid were shown to be actively internalized into the cytoplasm and converted into GM2 oligosaccharide. The in vivo synthesis of GM1 oligosaccharide was achieved by taking a similar approach but using strain TA05, which additionally overexpressed the gene for beta-1,3-galactosyltransferase. In high-cell-density cultures, the production yields for the GM2 and GM1 oligosaccharides were 1.25 g L(-1) and 0.89 g L(-1), respectively.     

An investigation of training strategies to improve alarm reactions

Researchers have suggested that operator training may improve operator reactions; however, researchers have not documented this for alarm reactions. The goal of this research was to train participants to react to alarms using sensor activity patterns. In Experiment 1, 80 undergraduates monitored a simulated security screen while completing a primary word search task. They received spatial, temporal, single sensor, or no training to respond to alarms of differing reliability levels. Analyses revealed more appropriate and quicker reactions when participants were trained and when the alarms were reliable. In Experiment 2, 56 participants practiced time estimation by simple repetition, performance feedback, or performance feedback and temporal subdivision. They then reacted to alarms based on elapsed time between sensor activity and alarm onset. Surprisingly, results indicated that participants did not benefit differentially from temporal interval training, focusing instead on advertised system reliability. Researchers should replicate these findings with realistic tasks and real-world complex task operators.     

The effect of pre-warming on performance during simulated firefighting exercise

This study examined the effect of active pre-warming on speed and quality of performance during simulated firefighting exercise. Twelve male firefighters performed two trials in counterbalanced order. They were either pre-warmed by 20-min cycling at 1.5 Watt kg⁻¹ body mass (WARM) or remained thermoneutral (CON) prior to a simulated firefighting activity. After the pre-warming, gastrointestinal temperature (P < 0.001), skin temperature (P = 0.002), and heart rate (P < 0.001) were higher in WARM than in CON. During the firefighting activity, rating of perceived exertion, thermal sensation and discomfort were higher for WARM than for CON. Finish time of the firefighting activity was similar, but the last task of the activity was completed slower in WARM than in CON (P = 0.04). In WARM, self-reported performance quality was lower than in CON (P = 0.04). It is concluded that pre-warming reduces the speed during the last part of simulated firefighting activity and reduces self-reported quality of performance.     

Target following with motion prediction for unmanned surface vehicle operating in cluttered environments

The capability of following a moving target in an environment with obstacles is required as a basic and necessary function for realizing an autonomous unmanned surface vehicle (USV). Many target following scenarios involve a follower and target vehicles that may have different maneuvering capabilities. Moreover, the follower vehicle may not have prior information about the intended motion of the target boat. This paper presents a trajectory planning and tracking approach for following a differentially constrained target vehicle operating in an obstacle field. The developed approach includes a novel algorithm for computing a desired pose and surge speed in the vicinity of the target boat, jointly defined as a motion goal, and tightly integrates it with trajectory planning and tracking components of the entire system. The trajectory planner generates a dynamically feasible, collision-free trajectory to allow the USV to safely reach the computed motion goal. Trajectory planning needs to be sufficiently fast and yet produce dynamically feasible and short trajectories due to the moving target. This required speeding up the planning by searching for trajectories through a hybrid, pose-position state space using a multi-resolution control action set. The search in the velocity space is decoupled from the search for a trajectory in the pose space. Therefore, the underlying trajectory tracking controller computes desired surge speed for each segment of the trajectory and ensures that the USV maintains it. We have carried out simulation as well as experimental studies to demonstrate the effectiveness of the developed approach.