Sustainability assessment of dwellings – a comparison of methodologies

Building sustainability assessment tools (BSATs) aim to promote and rank the sustainability of building stock. This paper makes a deep comparative analysis on how dwellings are evaluated by five BSAT and one performance-based design tool. The comparison is based on: (i) the purpose of assessment; (ii) sustainability dimensions considered; (iii) indicators addressed; (iv) life cycle phases considered by the indicators; (v) type of indicators; (vi) measurements; (vii) aggregation processes; and (vii) life cycle phases during which the assessment was carried out. The evaluation showed that the scope of BSAT varies significantly as well as the life cycle phases addressed in the assessment. Financial issues are often excluded from the assessment. None of the schemes is totally quantitative or qualitative in their measurement system; all have different types of indicators and different ways to assess them. This research provides researchers and stakeholders with important inside knowledge on the tools that allow the development and construction of more sustainable buildings.     

Molds and Resists Studies for Nanoimprint Lithography of Electrodes in Low-Voltage Polymer Thin-Film Transistors

A low-cost patterning of electrodes was investigated looking forward to replacing conventional photolithography for the processing of low-operating voltage polymeric thin-film transistors. Hard silicon, etched by sulfur hexafluoride and oxygen gas mixture, and flexible polydimethylsiloxane imprinting molds were studied through atomic force microscopy (AFM) and field emission gun scanning electron microscopy. The higher the concentration of oxygen in reactive ion etching, the lower the etch rate, sidewall angle, and surface roughness. A concentration around 30 % at 100 mTorr, 65 W and 70 sccm was demonstrated as adequate for submicrometric channels, presenting a reduced etch rate of 176 nm/min. Imprinting with positive photoresist AZ1518 was compared to negative SU-8 2002 by optical microscopy and AFM. Conformal results were obtained only with the last resist by hot embossing at 120 °C and 1 kgf/cm² for 2 min, followed by a 10 min post-baking at 100 °C. The patterning procedure was applied to define gold source and drain electrodes on oxide-covered substrates to produce bottom-gate bottom-contact transistors. Poly(3-hexylthiophene) (P3HT) devices were processed on high-κ titanium oxynitride (TiO _x N _y ) deposited by radiofrequency magnetron sputtering over indium tin oxide-covered glass to achieve low-voltage operation. Hole mobility on micrometric imprinted channels may approach amorphous silicon (～0.01 cm²/V s) and, since these devices operated at less than 5 V, they are not only suitable for electronic applications but also as sensors in aqueous media.     

Relationship between solar radiation and surface distribution of vegetation in Fildes Peninsula and Ardley Island,Maritime Antarctica

The aim of this work is to produce a simplified vegetation map of ice-free areas of the Fildes Peninsula (FP) and Ardley Island (AI) thought object-oriented classification using a QuickBird satellite image and to evaluate the influence of the global solar radiation (GSR) over the vegetation distribution. The vegetation data were generated from multiresolution segmentation using the panchromatic and infrared layers, and for the classification we calculated the normalized vegetative difference index (NVDI) and the green NVDI. Two classes were created – Lichen and Moss Cushion SubFormation and Moss Subformation – with 48 vegetation samples collected on surveys during the austral summers of 2008 and 2009. We used a kappa index to evaluate the classification efficiency using 100 sampled points obtained in austral summer of 2013. The GSR was estimated, and in order to evaluate the effect of meteorological phenomena and cloudless, we measured the GSR using a net radiometer model CNR4 installed in FP between 2014 and 2016. The estimate of GSR was done for seasons of 2015, in order to estimate the light compensation point and the saturation point for the plant communities in FP and AI. The kappa index was 0.73 and the global accuracy was 0.78, showing consistency between the classification and ground truth. The area was covered by vegetation in FP was 16.7% and in AI is 59.1%. The vegetation cover is distributed differently at FP and AI, and our results suggest GSR plays an important role in vegetation distribution and these tendencies could be related to greater GSR demand by mosses when compared to lichens.     

Experimental study of drop impacts and spreading on epicarps: Effect of fluid properties

The fluid mechanic of liquid drop impacts on solid food plays an important role in food engineering, e.g. when a spray technology is used to apply a coating. In the present work, drop impact behavior on banana and purple cabbage epicarps using high speed camera was studied. Drop velocity was controlled by modifying the height from which drop was ejected. Weber number varied from 100 to 800, whereas Reynolds number ranged from 1000 to 12,500. Liquid drop viscosity and surface tension effects on drop impact behavior were evaluated and temporal evolution of both spreading and flattening factors are presented. Results show that viscosity and epicarp surface properties had great influence on impact dynamics. For low viscosity liquid drops (water and Tween 20-water), the maximum spread factor, ξ_max, scaled with We^0.25±0.02, whereas for viscous fluid (water-glycerol mixture) it scaled with We^0.16±0.02. Finally, a new model was proposed to better fit the experimental data than the Roisman’s and Scheller’s models.     

Characterization of a water-based paint for corrosion protection

Corrosion of steel rebars in reinforced concrete is one of the major problems in the construction industry. Carbonation reactions of concrete with carbon dioxide and, mainly, the chloride salts action are the main causes responsible for concrete degradation. Protective coatings help to improve the durability of concrete structures by acting as a physical barrier against the corrosion agents. Waterborne paints are usually used for concrete protection rather than solvent-based paints since they are less pollutant. The aim of this work is to investigate the influence of the pore size and porosity on the permeability of the paints films toward sodium chloride. Three characterization methods from membrane science were implemented to characterize paint coatings. The time-lag method was used to determine the permeability toward the sodium chloride and toward helium and argon, these for approximately 100% relative humidity. From the seven waterborne paints formulated, only one was found to be suitable for surface protection of reinforced concrete, since its permeability toward NaCl was smaller than 10⁻¹⁴ m² s⁻¹, the threshold value required by National Laboratory of Civil Engineering (LNEC) in Portugal. For the formulated paints, it was observed that the average pore size correlates well with the permeability toward sodium chloride. This is an important result since obtaining the permeability toward sodium chloride of corrosion protective paints is very time consuming, while the average pore size can be obtained in a much shorter time.     

Stability of microencapsulated lactic acid bacteria under acidic and bile juice conditions

The probiotic strains Lactobacillus brevis CCMA1284 and Lactobacillus plantarum CCMA0359 were microencapsulated by spray drying using different matrices – whey powder (W), whey powder with inulin (WI) and whey powder with maltodextrin (WM). Viability of the microencapsulated strains in acid and bile juices and during 90 days of storage (seven and 25 °C) was evaluated. The two strains exhibited high encapsulation efficiency (> 86%) by spray drying. The different matrices maintained L. plantarum viability above six log CFU g⁻¹ at 7 °C for 90 days, whereas similar results for L. brevis were observed only for W. The use of inulin as matrix of encapsulation did not enhance bacterial viability in the evaluated conditions. In general, the use of W and WM as matrices was effective for L. plantarum viability. However, only W was effective for L. brevis in the evaluated conditions. The spray drying technique was successfully adopted for the encapsulation of L. plantarum CCMA0359 and L. brevis CCMA1284 strains.     

Microencapsulation of cashew apple (Anacardium occidentale,L.) juice using a new chitosan–commercial bovine whey protein isolate system in spray drying

The aim of this work was to obtain a new stable food product from cashew apple juice encapsulated by spray-drying technique using chitosan–whey protein isolate systems. The materials were evaluated according to their physicochemical stability during storage at different conditions and characterized with respect to their particle size distribution and structure. Encapsulated commercial and natural juices showed homogenous and unimodal particle size distribution with diameters ranging from 0.2 to 5.0 μm and from 0.2 to 40.0 μm, respectively. Both juices demonstrated higher physicochemical stability for vitamin C and color measurements than their respective non-encapsulated juices. X-ray diffractograms evidenced that the powder juices after the 140th day of storage were still in amorphous state. These results indicate that the new product was effective in protecting sensitive compounds present in the food matrix and it was also able to remain stable throughout the study period.     

Tokens vs. Signals: On Conformance between Formal Models of Dataflow and Hardware

Designing hardware often involves several types of modeling and analysis, e.g., in order to check system correctness, to derive performance properties such as throughput, to optimize resource usages (e.g., buffer sizes), and to synthesize parts of a circuit (e.g., control logic). Working directly with low-level hardware models such as finite-state machines (FSMs) to answer such questions is often infeasible, e.g., due to state explosion. Instead, designers often use dataflow models such as SDF and CSDF, which are more abstract than FSMs, and less expensive to use since they come with more efficient analysis algorithms. However, dataflow models are only abstractions of the real hardware, and often omit critical information. This raises the question, when can one say that a certain dataflow model faithfully captures a given piece of hardware? The question is of more than simply academic interest. Indeed, as illustrated in this paper, dataflow-based analysis outcomes may sometimes be defensive (e.g., buffers that are too big) or even incorrect (e.g., buffers that are too small). To answer the question of faithfully capturing hardware using dataflow models, we develop a formal conformance relation between the heterogeneous formalisms of (1) finite-state machines with synchronous semantics, typically used to model synchronous hardware, and (2) asynchronous processes communicating via queues, used as a formal model for dataflow. The conformance relation preserves performance properties such as worst-case throughput and latency.