Entwicklung einer kontinuierlichen Mikrowellen‐Vakuumtrocknungsanlage mit hexagonalem Verfahrensraum

A continuous microwave vacuum drying processor with a hexagonal cross‐section of the cavity was constructed. Due to the geometry of the cavity and the continuous movement of the product, homogeneous microwave power absorption of the product can be favored. By the expansion and simultaneous dehydration of non‐expanded, starch‐based extrudates, the applicability of the constructed processor could be shown.     

Experimental Phase Diagram Determination and Thermodynamic Assessment of the CeO2‐Gd2O3‐CoO System

New phase diagram data and a thermodynamic assessment of the CeO‐Gd₂O₃‐CoO system using the CALPHAD approach are presented. This information is needed to understand the surprisingly low sintering temperature (950°C–1050°C) of CeO₂‐based materials doped with small amounts of transition metal oxide (e.g., CoO). Experimental phase equilibria between 1100°C and 1300°C are reported based on the analysis of annealed and molten samples. No isolated compound exists in the ternary. At 1300°C the Co solubility in the ternary compounds Ce_1?x?yGd_xCo_yO_2?x/2?y (fluorite) is 2.7 mol% and is less than 1 mol% in the Gd_2?xCe_xO_3+x/2 (bixbyite). The Ce solubility in the perovskite GdCoO_3?δ was found to be 1 mol%. The lowest temperature eutectic melt in the ternary has a composition of 57.2 mol% Co and 41.1 mol% Gd melting at an onset temperature of 1303 ± 5°C, which is close to the binary eutectic in the Gd₂O₃‐CoO system at 60 ± 2 mol% Co and 1348 ± 1°C.     

Relevance of the acid–base approach in prediction of adhesion properties in two‐component injection moulding

We demonstrate the use of innovative wetting method in prediction of the adhesion properties of biobased polymers for two‐component injection moulding, taking into account the acid–base surface properties of joined materials. The measurements were carried out in accordance with modified Berger method by calculation of the difference in shortened acidity parameter ΔD_short between hard and soft component. Correlation factors up to 0.99 were observed between ΔD_short and peel force. In comparison to results obtained by conventional wetting methods, high potential for the selection of components with high interface adhesion and for prediction of the functionality by the acid–base approach was demonstrated. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43048.     

A new method of measuring and presenting the membrane fouling potential

The silt density index (SDI) and modified fouling index (MFI) characterisation methods are well known for the evaluation of membrane fouling potential of dispersed particulate matter (suspended solids, colloids) in a feed. The SDI and MFI methods, however, reduce the overall and very complex fouling phenomena into a one number value, on which the interpretation of the fouling potential of the feed is based. Considering such a one number characteristic, a significant amount of information from the fouling measurement (data) is lost. In this paper a concept is introduced in order to preserve such information and supplement the existing indexes. The proposed method measures, processes and presents data in a specific format. To illustrate the concept, some results are shown from measurements on three types of feed. Future systematic research will also include the measurement on some model feeds with, for example, well characterised dispersions for comparison purposes. However, based on the contents of this paper, a discussion on the method could be initiated.     

Is the particle deposition in a cell exposure facility comparable to the lungs? A computer model approach

Abstract

Cell exposure experiments at the air-liquid interface (ALI) are used increasingly as indicators for health effects and for the impact of aerosols on the lung. Thereby the aerosol particles are kept airborne and can deposit on a cell surface area similar to the human respiratory tract (RT). However, geometry and air flow rates of an ALI system deviate considerably from the RT. As the tissue-delivered particle dose to the lungs (TD) can hardly be measured, computer models of particle deposition are used here to mimic both the particle deposition at ALI and in the RT. An ALI exposure setup (VitroCell GmbH) for an airflow rate of 100 cm³ min^?1 is selected, where the particle deposition model has been verified experimentally. For the RT we use the hygroscopic lung deposition model of Ferron et al. (2013 Ferron, G. A., S. Upadhyay, R. Zimmermann, and E. Karg. 2013. Model of the deposition of aerosol particles in the respiratory tract of the rat. II. Hygroscopic particle deposition. J. Aerosol Med. Pulm. Drug Deliv. 26 (2):101–19. doi:10.1089/jamp.2011.0965.[Crossref], [PubMed], [Web of Science ®] , [Google Scholar]). Model runs are performed for the particle deposition and for the deposited particles per surface area in both the ALI and the RT. The results show that the ALI-deposited mass is 1-2 orders of magnitude higher than in the alveolar region, because the surface area of the lung region is substantially larger. A particle size range from 40 to 450 nm is identified, where the ratio of both the deposition in a lung region and the deposition at the ALI varies by a factor less than two. Mean values for this ratio are 31 and 101 for the tracheo-bronchial and the alveolar region, respectively. The same size range is found for the ratio of the deposited particles per surface area in a lung region and at the ALI. For this range the mean surface deposition at the ALI is 23- and 1575-times larger than in the tracheo-bronchial and the alveolar lung region, respectively. The effect is partly compensated by different flow rate and cell size.

Copyright © 2020 American Association for Aerosol Research     

Structural properties of nanocomposites based on resole-type phenol-formaldehyde oligomers and detonation nanodiamonds

Using the methods of infrared spectroscopy (IRS) and X-ray photoelectron spectroscopy (XPS), it was shown that short-term high-energy machining of detonation nanodiamonds (DND) leads to structural changes in the crystal structure and functional composition of the surface layer on particles. The possibility of spontaneous formation for stable colloidal systems with a narrow size distribution of mechanically activated DND in phenol-formaldehyde oligomers (PFO) was established. By molecular spectroscopy it was revealed that π → π* interactions of the aromatic rings of PFO are caused by orientational phenomena as a result of hydrogen bonds between an activated DND surface and functional groups of PFO. The effect of DND concentration on the curing reaction parameters ofpsgr the phenol-formaldehyde oligomer was determined by differential scanning calorimetry (DSC). The concentration effect of mechanically activated nanodiamonds on the physical and mechanical characteristics of a composite material based on phenol-formaldehyde binder and polyamide paper (Nomex) was studied. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48582.     

Adaptive Immune Responses in a Multiple Sclerosis Patient with Acute Varicella-Zoster Virus Reactivation during Treatment with Fingolimod

Fingolimod, an oral sphingosine 1-phosphate (S1P) receptor modulator, is approved for the treatment of relapsing forms of multiple sclerosis (MS). The interference with S1P signaling leads to retention particularly of chemokine receptor-7 (CCR7) expressing T cells in lymph nodes. The immunological basis of varicella zoster virus (VZV) infections during fingolimod treatment is unclear. Here, we studied the dynamics of systemic and intrathecal immune responses associated with symptomatic VZV reactivation including cessation of fingolimod and initiation of antiviral therapy. Key features in peripheral blood were an about two-fold increase of VZV-specific IgG at diagnosis of VZV reactivation as compared to the previous months, a relative enrichment of effector CD4+ T cells (36% versus mean 12% in controls), and an accelerated reconstitution of absolute lymphocytes counts including a normalized CD4+/CD8+ ratio and reappearance of CCR7+ T cells. In cerebrospinal fluid (CSF) the lymphocytic pleocytosis and CD4+/CD8+ ratios at diagnosis of reactivation and after nine days of fingolimod discontinuation remained unchanged. During this time CCR7+ T cells were not observed in CSF. Further research into fingolimod-associated VZV reactivation and immune reconstitution is mandatory to prevent morbidity and mortality associated with this potentially life-threatening condition.     

Syntheses of 1,2,4-triazolo[4,3-c]pteridines. Potential substrates for xanthine oxidase

A synthetic route for the preparation of 9-phenyl-1,2,4-triazolo[4,3-c]pteridines 8 is described. Their reactivities towards xanthine oxidase from Arthrobacter M-4 are determined and compared with the pteridine derivatives 6-phenylpteridin-4[3H]-thione 5, 6-phenyl-4-thiomethylpteridine 6, 4-hydrazino-6-phenylpteridine 7, 3-N-methyl-6-phenylpteridin-4[3H]-thione 19, 4-amino-6-phenylpteridine 22 and 1-N-methyl-6-phenylpteridin-4[1H]-one 24, in order to inspect a possible influence of pyrimidine ring substitution pattern on their interaction with the bacterial enzyme. It has been suggested that a planar structure of the pteridine moiety and the substituents could be an important factor that so far has been overlooked when considering the enzyme activity. Some literature data are also discussed in view of revision of structure assignment of the compounds 12, 14, and 17. This revised version was published online in August 2006 with corrections to the Cover Date.